Effect of thermomechanical processing on compressive mechanical properties of Ti–15Mo additively manufactured by laser metal deposition
Source abstract
Abstract
A bidirectional powder deposition strategy was employed to additively manufacture Ti–15Mo wt% using laser metal deposition. The as-built alloy was subsequently subjected to post-fabrication uniaxial thermomechanical processing at strain rates of 0.00055s−1, 0.0011s−1, 1s−1, and 4s−1, with strains of 20 % and 40 %. Experiments were conducted at room and elevated temperatures. Phase identification, elemental and microstructural characterisation were conducted using x-ray diffraction, energy dispersive spectroscopy and scanning electron microscopy. The three distinct zones, namely the fusion, remelted and heat affected zones, identified in each deposited layer of the as-built microstructure were retained after thermomechanical processing. After processing, electron backscatter diffraction was used to analyse deformation mechanisms. Deformation accommodation in β matrix was predominantly by a combination of slip and α′′ martensite which formed as a primary product at columnar and sub-columnar grain boundaries. However, the operation of {332}〈113〉 and {112}〈111〉 β-twinning was also determined, howbeit with a very small surface fraction. This implies a small surface fraction of secondary α′′ martensite forming within β-twins in the deformed microstructure. Compressive mechanical properties showed a strong dependence on strain rate as higher flow stress and compressive strength were obtained at higher strain rates. Grain structure homogenisation was not achieved after thermomechanical processing as there were α dominated regions as well as martensite/twin dominated regions which implies that an-isotropic tensile properties would emerge after tensile deformation on multiple pre-TMCPed samples. However, columnar β-grains were refined by a combination of precipitated α and deformation induced β-twins and martensite.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Titanium Alloys Microstructure and Properties · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (74)
Show source-provided references
1. Thermomechanical processing of beta titanium alloys—an overview10.1016/S0921-5093(97)00783-1 ↗
2. Structural characterization of Ti-15Mo alloy used as biomaterial by Rietveld method10.1063/1.4707920 ↗
3. Characterization of ti-15Mo beta titanium alloy for orthopaedic
4. Mechanical properties of biomedical titanium alloys10.1016/S0921-5093(97)00806-X ↗
5. Properties and applications of titanium alloys: a brief review
6. Beta titanium alloys: the lowest elastic modulus for biomedical applications: a review
7. Titanium alloys for biomedical applications10.1007/978-3-662-46836-4_8 ↗
8. Biocompatibility of β-stabilizing elements of titanium alloys
9. Mechanical biocompatibilities of titanium alloys for biomedical applications10.1016/j.jmbbm.2007.07.001 ↗
10. Laser additive manufacturing-direct energy deposition of Ti-15Mo biomedical alloy: artificial neural network based modeling of track dilution10.1007/s40516-020-00117-z ↗
11. A comparison of tensile properties and corrosion behavior of cast Ti–7.5 Mo with cp Ti, Ti–15Mo and Ti–6Al–4V alloys10.1016/j.jallcom.2007.10.054 ↗
12. Strengthening and toughening of titanium alloys10.2355/isijinternational.31.785 ↗
13. A comparative study of the mechanical properties of high-strength β-titanium alloys10.1016/j.jallcom.2007.03.070 ↗
14. Wohlers · 2016
15. Laser metal deposition as repair technology for stainless steel and titanium alloys10.1016/j.phpro.2012.10.051 ↗
16. Fatigue properties of a titanium alloy (Ti–6Al–4V) fabricated via electron beam melting (EBM): effects of internal defects and residual stress10.1016/j.ijfatigue.2016.04.022 ↗
17. Layer geometry control for the fabrication of lattice structures by wire and arc additive manufacturing
18. Effects of electroshock treatment on microstructure evolution and texture distribution of near-β titanium alloy manufactured by directed energy deposition10.1016/j.matchar.2020.110137 ↗
19. Tailoring grain morphology in Ti-6Al-3Mo through heterogeneous nucleation in directed energy deposition10.1016/j.jmst.2021.01.056 ↗
20. A review of laser engineered net shaping (LENS) build and process parameters of metallic parts10.1108/RPJ-04-2018-0088 ↗
21. Enhanced corrosion and wear resistance properties of carbon fiber reinforced Ni-based composite coating by laser cladding10.1016/j.surfcoat.2017.11.051 ↗
22. Phase separation and enhanced wear resistance of Cu88Fe12 immiscible coating prepared by laser cladding10.1016/j.jmrt.2018.12.018 ↗
23. Microstructures and mechanical behavior of beta-type Ti-25V-15Cr-0.2Si titanium alloy coating by laser cladding10.1016/j.msea.2020.140063 ↗
24. Additive manufacturing of metallic lattice structures: unconstrained design, accurate fabrication, fascinated performances, and challenges10.1016/j.mser.2021.100648 ↗
25. Critical review of the state of the art in multi-material fabrication via directed energy deposition10.1016/j.cossms.2021.100924 ↗
26. Review: the impact of metal additive manufacturing on the aerospace industry10.3390/met9121286 ↗
27. Laser additive manufacture of titanium alloys
28. Microstructure and mechanical properties of a novel β titanium metallic composite by selective laser melting10.1016/j.actamat.2014.01.018 ↗
29. Improvement in fatigue characteristics of newly developed beta type titanium alloy for biomedical applications by thermo-mechanical treatments10.1016/j.msec.2004.12.007 ↗
30. Influence of thermomechanical processing and heat treatment on microstructure, tensile properties and fracture toughness of Ti-1100-0.1 B alloy10.1016/j.jallcom.2013.11.014 ↗
31. Relationships among thermomechanical treatments, microstructure, and tensile properties of a near beta-titanium alloy: β-CEZ: Part II. Relationships between thermomechanical treatments and tensile properties10.1557/JMR.1996.0012 ↗
32. Stress-induced martensitic transformation in a β-solution treated Ti–10V–2Fe–3Al alloy during compressive deformation10.1016/j.msea.2020.140404 ↗
33. Strain rate dependence of deformation-induced transformation and twinning in a metastable titanium alloy10.1016/j.actamat.2015.11.026 ↗
34. Formation of deformation-induced products in a metastable-β titanium alloy during high temperature compression10.3390/met8020100 ↗
35. The influence of β phase stability on deformation mode and compressive mechanical properties of Ti–10V–3Fe–3Al alloy10.1016/j.actamat.2014.10.043 ↗
36. Effect of strain rate on stress-induced martensitic formation and the compressive properties of Ti–V–(Cr,Fe)–Al alloys10.1016/j.msea.2013.03.002 ↗
37. Tuning the stress induced martensitic formation in titanium alloys by alloy design10.1007/s10853-012-6263-z ↗
38. Effect of strain on microstructural development during uniaxial compression of metastable beta Ti–10V–2Fe–3Al alloy
39. A new method for evaluation of friction in bulk metal forming10.1016/j.jmatprotec.2004.03.029 ↗
40. Constitutive modelling of thermomechanical abnormalities due to dynamic strain aging in commercially pure titanium10.1016/j.jmrt.2023.06.273 ↗
41. Effect of dislocation density evolution on the thermomechanical response of metals with different crystal structures at low and high strain rates and temperatures
42. Thermomechanical constitutive behaviour of a near α titanium alloy over a wide range of strain rates: experiments and modelling10.1016/j.ijmecsci.2020.105970 ↗
43. An overview of the thermomechanical processing of α/β titanium alloys: current status and future research opportunities10.1007/s11661-020-05625-3 ↗
44. Microstructural characterisation and mechanical evaluation of Ti-15Mo manufactured by laser metal deposition10.1016/j.jallcom.2023.169553 ↗
45. Song · 2021
46. 2022
47. Friction coefficient in hot compression of cylindrical sample10.2320/matertrans.M2010056 ↗
48. On the nonuniform deformation of the cylinder compression test10.1115/1.482786 ↗
49. Inverse finite element modeling of the barreling effect on experimental stress-strain curve for high temperature steel compression test10.1016/j.jmatprotec.2017.01.012 ↗
50. Constitutive model of the alloy 2117-T4 at low strain rates and temperatures10.1016/j.jmatprotec.2005.05.056 ↗
51. Effects of thermomechanical processing and heat treatment on the tensile and creep properties of boron-modified near alpha titanium alloy Ti-110010.1007/s11661-012-1394-z ↗
52. On the transformation pathways in TRIP/TWIP Ti–12Mo alloy10.1016/j.msea.2021.141672 ↗
53. Effect of oxygen content on the mechanical properties and plastic deformation mechanisms in the TWIP/TRIP Ti–12Mo alloy
54. On the design of new β-metastable titanium alloys with improved work hardening rate thanks to simultaneous TRIP and TWIP effects10.1016/j.scriptamat.2012.01.049 ↗
55. Design of a novel Mn-based 1GPa duplex stainless TRIP steel with 60% ductility by a reduction of austenite stability10.1016/j.actamat.2011.04.011 ↗
56. Formation and reversion of stress induced martensite in Ti-10V-2Fe-3Al10.1016/0001-6160(82)90137-7 ↗
57. The influence of thermomechanical processing on microstructural evolution of Ti600 titanium alloy10.1016/j.msea.2011.08.007 ↗
58. Observation of simultaneous operation of deformation twins in both α and β phases in metastable β titanium alloy10.1016/j.jallcom.2022.164794 ↗
59. Deformation behaviour of beta titanium alloy Ti–10V–4.5 Fe–1.5 Al in hot upset forging10.1016/S0921-5093(01)01982-7 ↗
60. Constitutive model for a new kind of metastable β titanium alloy during hot deformation10.1016/S1003-6326(11)61225-9 ↗
61. Effect of hot compressive deformation on the martensite transformation of Ti–10V–2Fe–3Al titanium alloy10.1016/j.msea.2011.10.028 ↗
62. Characterization of hot deformation behavior of a new near beta titanium alloy: Ti-733310.1016/j.matdes.2013.02.044 ↗
63. The onset of twinning in metals: a constitutive description10.1016/S1359-6454(01)00300-7 ↗
64. Deformation mechanisms of Ti–6Al–4V alloy with a martensitic microstructure subjected to oligocyclic fatigue10.1016/S1359-6454(00)00152-X ↗
65. Twinning system selection in a metastable β-titanium alloy by Schmid factor analysis10.1016/j.scriptamat.2011.02.033 ↗
66. ω phase acts as a switch between dislocation channeling and joint twinning- and transformation-induced plasticity in a metastable β titanium alloy10.1016/j.actamat.2018.03.053 ↗
67. Thermo-mechanical processing of high strength β-titanium alloys and effects on microstructure and properties10.1016/S0924-0136(01)00788-9 ↗
68. ω-Assisted nucleation and growth of α precipitates in the Ti–5Al–5Mo–5V–3Cr–0.5Fe β titanium alloy10.1016/j.actamat.2009.01.007 ↗
69. The room temperature tensile deformation behavior of thermomechanically processed β-metastable Ti-Nb-Ta-Zr bio-alloy: the role of deformation-induced martensite10.1016/j.msea.2018.09.038 ↗
70. Modeling constitutive relationship of Ti40 alloy using artificial neural network10.1016/j.matdes.2010.10.004 ↗
71. Suwas · 2014
72. Nucleation and preferential growth mechanism of recrystallization texture in high purity binary magnesium-rare earth alloys10.1016/j.actamat.2017.07.038 ↗
73. Texture evolution and the recrystallization behavior in a near β titanium alloy Ti-7333 during the hot-rolling process10.1016/j.matchar.2019.109999 ↗
74. Boeckels · 2012