journal article·2019-02

Plastic Instability in Co-Cr-Ni-Mo alloy wires drawn with different drawing practices

Sai Srikanth GVK, M.J. Tan, Zhenyun Liu

Publisher page

Abstract

Abstract Plastic instability of Co-35Ni-20Cr-10Mo alloy was studied by inflicting the material to the different drawing process, namely Full Die Drawing (FDD) and Half Die Drawing (HDD). The wires were subjected to different plastic deformations, by varying the amount of cold work (CW) reduction, and the strain hardening exponent (γ) and strain rate sensitivity (m) were determined from the logarithmic plots of the true stress and strain curves. The experimental results indicated that wires drawn with FDD practice, when compared with the HDD drawn wires, had a lower instability until 75% CW, after which it increased significantly when drawn to 95% CW. The lower instability in the FDD wires at 75% CW, was attributed to the smaller grain size, higher dislocation density and lower twin spacing which contributed to higher γ and m. Plastic strain localization because of shear band formation was noticed in the FDD 95% CW wires, which contributed to lowered ductility and increased instability in the wire due to reduced γ and m. This phenomenon was not observed in HDD wires. Therefore, the results illustrate that the drawing technique employed to process the material has a significant impact on the plastic instability of the material, with the FDD practice recommended for lower CW deformations and HDD for higher CW deformations.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Microstructure and Mechanical Properties of Steels · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (71)

Show source-provided references
2. Koch · 2006
3. Plastic strain localization in metals: origins and consequences10.1016/j.pmatsci.2013.06.001 ↗
4. What governs ductility of ultrafine-gra metals? A microstructure based approach to necking instability10.1016/j.actamat.2017.08.069 ↗
5. Plastic instability: criteria and computational approaches10.1007/BF03020127 ↗
6. Plastic instability in rate-dependent materials10.1016/0022-5096(67)90008-7 ↗
7. Plastic instability during tensile deformation of temper-annealed non-heat-treatable aluminium alloy sheets10.1016/S0924-0136(98)00017-X ↗
8. A. Considère, Mémoire sur l′emploi du fer et de l′acier dans les constructions, vol. (IX) of Annales des Ponts et Chaussées - Mémoires et documents, Dunod, 1885.
9. Theory of the tensile test10.1016/0001-6160(67)90211-8 ↗
10. Plastic instability and growth of grooves and patches in plates or tubes10.1016/0020-7403(72)90087-2 ↗
11. Tensile instability and necking in materials with strain hardening and strain-rate hardening10.1016/0001-6160(77)90072-4 ↗
12. Influence of strain-rate sensitivity on necking under uniaxial tension10.1016/0001-6160(77)90168-7 ↗
13. Plastic instability in uniaxial tension tests10.1016/0001-6160(81)90124-3 ↗
14. A generalized criterion of plastic instabilities and its application to creep damage and superplastic flow10.1016/0956-7151(95)00091-9 ↗
15. Plastic instabilities and uniaxial tensile ductilities10.1016/0001-6160(80)90144-3 ↗
16. Instability of plastic flow in tension10.1016/0036-9748(78)90241-7 ↗
17. Instability of plastic flow in the directions of pure shear: ii10.1007/BF02672294 ↗
18. Physics and phenomenology of strain hardening: the FCC case10.1016/S0079-6425(02)00003-8 ↗
19. A constitutive description of the deformation of copper based on the use of the mechanical threshold stress as an internal state variable10.1016/0001-6160(88)90030-2 ↗
20. Ductility of ultrafine grained copper10.1063/1.1426697 ↗
21. Instabilities and ductility of nanocrystalline and ultrafine-grained metals10.1016/S1359-6462(03)00396-8 ↗
22. Three strategies to achieve uniform tensile deformation in a nanostructured metal10.1016/j.actamat.2003.12.022 ↗
23. Study on the deformation homogeneity and electrical conductivity in Co-Cr-Ni-Mo wires drawn with different drawing practices10.1007/s11665-018-3755-2 ↗
24. Influence of drawing practices on the mechanical, texture and work hardening characteristics of Co-Cr-Ni-Mo wires10.1016/j.msea.2017.12.063 ↗
25. Analysis of strain rate sensitivity and strain rate hardening in Co–Cr–Ni–Mo wires drawn with different drawing practices10.1007/s12540-019-00239-w ↗
26. S. Gaylord, Cobalt-nickel base alloys containing chromium and molybdenum, Google Patents, 1967.
27. ASTM F562-13, Standard Specification for Wrought 35Cobalt-35Nickel-20Chromium-10Molybdenum Alloy for Surgical Implant Applications (UNS R30035), ASTM International, West Conshohocken, PA, 2013, 2013.
28. ASTM A931-18 Standard Test Method for Tension Testing of Wire Ropes and Strand, ASTM International, West Conshohocken, PA, 〈https://doi-org.ezlibproxy1.ntu.edu.sg/10.1520/A0931-18〉, 2018.
29. Focused ion beams techniques for nanomaterials characterization10.1002/jemt.20324 ↗
30. A review of focused ion beam milling techniques for TEM specimen preparation10.1016/S0968-4328(99)00005-0 ↗
31. The application of focused ion beam microscopy in the material sciences10.1016/j.matchar.2008.11.014 ↗
32. Recent advances in FIB–TEM specimen preparation techniques10.1016/j.matchar.2005.12.007 ↗
33. Applications of the FIB lift‐out technique for TEM specimen preparation10.1002/(SICI)1097-0029(19980515)41:4<285::AID-JEMT1>3.0.CO;2-Q ↗
34. FIB lift-out specimen preparation techniques
35. In situ lift-out dedicated techniques using FIB–SEM system for TEM specimen preparation10.1016/j.micron.2012.05.006 ↗
36. A FIB micro-sampling technique and a site specific TEM specimen preparation method
37. Improved focused ion beam target preparation of (S) TEM specimen—A method for obtaining ultrathin lamellae10.1017/S1431927611012499 ↗
38. Plastic instability and strain rate sensitivity of ultrafine-grained iron10.1016/j.jallcom.2009.08.004 ↗
39. Strain rate sensitivity of ultrafine-grained aluminium processed by severe plastic deformation10.1016/j.scriptamat.2005.03.043 ↗
40. Nanocrystalline materials: controlling plastic instability10.1038/nmat797 ↗
41. Strain hardening, strain rate sensitivity, and ductility of nanostructured metals10.1016/j.msea.2003.10.214 ↗
42. Influence of grain size and stacking-fault energy on deformation twinning in fcc metals10.1007/s11661-999-0272-9 ↗
43. High-strain-rate deformation: mechanical behavior and deformation substructures induced10.1146/annurev-matsci-070511-155034 ↗
44. High strain rate properties of metals and alloys10.1179/174328008X277795 ↗
45. Strain rate sensitivity and evolution of dislocations and twins in a twinning-induced plasticity steel10.1016/j.actamat.2015.01.013 ↗
46. Grain size dependence of the plastic deformation kinetics in Cu10.1016/S0921-5093(02)00238-1 ↗
47. Nanocrystalline electrodeposited Ni: microstructure and tensile properties10.1016/S1359-6454(02)00198-2 ↗
48. Effect of nanocrystalline and ultrafine grain sizes on the strain rate sensitivity and activation volume: fcc versus bcc metals10.1016/j.msea.2004.03.064 ↗
49. Dieter · 1986
50. Flow stress analysis of TWIP steel via the XRD measurement of dislocation density10.1016/j.msea.2010.01.033 ↗
51. Strain hardening rate sensitivity and strain rate sensitivity in TWIP steels10.1016/j.msea.2015.01.080 ↗
52. Dislocation mechanics aspects of plastic instability and shear banding10.1016/0167-6636(94)90069-8 ↗
53. Orientation-dependent hardness and strain rate sensitivity in nanotwin copper10.1063/1.4731242 ↗
54. Plastic instability in an omega forming Ti-15% Mo alloy10.1016/1359-6454(96)00012-2 ↗
55. Strain rate sensitivity of face-centered-cubic nanocrystalline materials based on dislocation deformation10.1063/1.2186981 ↗
56. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗
57. Microstructural processes of plastic instabilities in strengthened metals10.1016/0079-6425(91)90002-B ↗
58. Plastic instabilities and dislocation densities during plastic deformation in Al–Mg alloys10.1016/j.msea.2006.09.019 ↗
59. On dislocation storage and the mechanical response of fine scale microstructures10.1016/0956-7151(94)90030-2 ↗
60. Evaluation of the role of deformation twinning in work hardening behavior of face-centered-cubic polycrystals10.1007/s11661-007-9356-6 ↗
61. Strain-rate sensitivity, activation volume and mobile dislocations exhaustion rate in nanocrystalline Cu–11.1 at% Al alloy with low stacking fault energy10.1016/j.msea.2014.05.093 ↗
62. Competing regimes of rate dependent plastic flow in ultrafine grained metals10.1016/j.msea.2012.09.072 ↗
63. Evolution and microstructure of shear bands in nanostructured Fe10.1063/1.1501158 ↗
64. The strength of nanocrystalline metals with and without flaws10.1016/S0921-5093(97)00185-8 ↗
65. Effects of nanocrystalline and ultrafine grain sizes on constitutive behavior and shear bands in iron10.1016/S1359-6454(03)00169-1 ↗
66. Work hardening and inherent plastic instability of nanocrystalline metals10.1002/pssr.201004095 ↗
67. Plastic deformation and fracture of ultrafine-grained Al–Mg alloys with a bimodal grain size distribution10.1016/j.actamat.2005.11.044 ↗
68. On the grain size softening in nanocrystalline materials10.1016/S1359-6462(00)00320-1 ↗
69. A model for the deformation of nanocrystalline materials10.1080/01418639708241122 ↗
70. Mechanical properties of nanostructured materials10.1016/S0921-5093(00)01437-4 ↗
71. Revisiting the Considère criterion from the viewpoint of dislocation theory fundamentals10.1016/j.scriptamat.2013.12.009 ↗