Depth-resolved mechanical behaviour of shot peened 7050-T7451 aluminium surfaces using in-situ synchrotron X-ray diffraction
Source abstract
Abstract
We have assessed the elasto-plastic (sub)surface behaviour of 7050-T7451 aluminium alloy treated by shot peening using S110 steel shots of 300 μm in diameter and two different intensities, namely Almen intensity (A) of 3.4 (low-intensity) and 10.9 (high-intensity). Shot peening (SP) is a cold work process applied in the aerospace industry to enhance the fatigue tolerance of structural components after machining. The local mechanical response within the SP-induced layer was depth profiled at room temperature by performing an X-ray micro-diffraction experiment in transmission geometry at a synchrotron source, during tensile loading of the specimen to rupture. The presence of a SP-induced layer in the specimen is evidenced by compressive longitudinal lattice strains (∼-540 με for low-intensity and ∼-4200 με for high-intensity at 0.1 mm from the surface for the 311 reflection), parallel with respect to the applied load, i.e. perpendicular to the direction of impact of the steel shots, and also by higher values of the Full-Width-at-Half-Maximum (FWHM) of the diffraction peaks than those measured in the bulk material, due to the local plastic deformation induced by shot peening. High-intensity shot peening produced a higher surface roughness (Sa ∼13 μm), and also two times thicker deformed surface layer (∼0.4 mm), than low-intensity shot peening (Sa ∼2 μm and ∼0.2 mm thick deformed layer). For both shot peening conditions, the local yield stress of the surface layer and bulk material were similar, however the severely affected layers exhibit a non-linear elastic behaviour when applying loads lower than the yield stress of the material. Beyond yielding, the presence of SP-induced layers is mainly evidenced by the relatively higher value of the FWHM near-surface compared to the bulk (∼20 % higher for low-intensity and ∼40 % for high-intensity), due to the initial plastic deformation accumulated during shot peening and additional plasticity during loading of the specimen.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Surface Treatment and Residual Stress · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Aluminum alloys in aircraft in the periods of 1970–2000 and 2001–201510.1023/A:1010453702596 ↗
2. Effect of cutting speed on the surface integrity of face milled 7050-T7451 aluminium workpieces10.1016/j.procir.2018.05.034 ↗
3. Distortion caused by residual stresses in machining aeronautical aluminum alloy parts: recent advances10.1007/s00170-016-9066-6 ↗
4. Surface integrity and fatigue analysis of shot-peening for 7055 aluminum alloy under different high-speed milling conditions10.1177/1687814016674628 ↗
5. The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T610.1016/j.msea.2009.03.020 ↗
6. Effects of wet shot peening on microstructures and mechanical properties of a 2060-T8 aluminum-lithium alloy10.1016/j.msea.2021.142436 ↗
7. Improvement of fatigue property in 7050–T7451 aluminum alloy by laser peening and shot peening10.1016/j.msea.2011.01.077 ↗
8. Shot peening
9. Numerical analysis of shot peening parameters for fatigue life improvement10.1063/1.5066858 ↗
10. The effect of residual stresses induced by shot‐peening on fatigue crack propagation in two high strength aluminium alloys10.1111/j.1460-2695.1987.tb00205.x ↗
11. Reverse bending fatigue of shot peened 7075-T651 aluminium alloy: the role of residual stress relaxation10.1016/j.ijfatigue.2008.11.017 ↗
12. Surface integrity of shot peened aluminium alloy 7075-T65110.5545/sv-jme.2010.142 ↗
13. Surface integrity and fatigue behavior in shot-peening for high-speed milled 7055 aluminum alloy10.1177/0954405415573704 ↗
14. The effects of laser peening and shot peening on high cycle fatigue in 7050-T7451 aluminum alloy10.1016/j.msea.2009.08.045 ↗
15. High-and very high-cycle plain fatigue resistance of shot peened high-strength aluminum alloys: the role of surface morphology10.1016/j.ijfatigue.2014.07.002 ↗
16. Becker · 2017
17. Experimental investigation and fatigue life prediction for 7475-T7351 aluminum alloy with and without shot peening-induced residual stresses10.1016/j.actamat.2011.03.013 ↗
18. Mechanical surface treatments on titanium, aluminum and magnesium alloys10.1016/S0921-5093(98)01168-X ↗
19. Analytical fatigue life prediction of shot peened AA 7050-T745110.1016/j.ijfatigue.2018.07.007 ↗
20. Two experimental methods to determining stress–strain behavior of work-hardened surface layers of metallic components10.1016/j.jmatprotec.2010.08.019 ↗
21. Evaluation of stress-strain behavior of surface treated steels by X-ray diffraction
22. Surface mechanical properties of S30432 austenitic steel after shot peening10.1016/j.apsusc.2012.05.122 ↗
23. Characterization on surface mechanical properties of Ti–6Al–4V after shot peening10.1016/j.jallcom.2016.01.119 ↗
24. Determination of surface mechanical property and residual stress stability for shot-peened SAF2507 duplex stainless steel by in situ X-ray diffraction stress analysis10.1016/j.jmrt.2020.05.028 ↗
25. A synchrotron X-ray diffraction study of in situ biaxial deformation10.1016/j.actamat.2015.02.009 ↗
26. Comparative micromechanics assessment of high-carbon martensite/bainite bearing steel microstructures using in-situ synchrotron X-ray diffraction10.1016/j.mtla.2020.100948 ↗
27. Surface morphology and microcrack formation for 7050-T7451 aluminum alloy in high speed milling10.1007/s00170-014-6605-x ↗
28. Effects of heterogeneity and coarse secondary phases on mechanical properties of 7050-T7451 aluminum alloy friction stir welding joint10.1016/j.msea.2019.138223 ↗
29. Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
30. 2023 · J2277
31. Complete elliptical ring geometry provides energy and instrument calibration for synchrotron-based two-dimensional X-ray diffraction10.1107/S0021889813022437 ↗
32. Processing two-dimensional X-ray diffraction and small-angle scattering data in DAWN 210.1107/S1600576717004708 ↗
33. Y. On the standards and practices for miniaturized tensile test–A review10.1016/j.fusengdes.2020.112006 ↗
34. The effects of laser peening and shot peening on mechanical properties in friction stir welded 7075-T7351 aluminum10.1007/s11665-007-9163-7 ↗
35. Al7050-T7451 turning simulation based on the modified power-law material model10.1007/s00170-009-2328-9 ↗
36. Modeling of flow behavior for 7050-T7451 aluminum alloy considering microstructural evolution over a wide range of strain rates10.1016/j.mechmat.2016.01.006 ↗
37. Analytical fatigue life prediction of shot peened Inconel 71810.1016/j.ijfatigue.2018.04.011 ↗
38. Schulze · 2006
39. Stability of machining induced residual stresses in Inconel 718 under quasi-static loading at room temperature10.1016/j.msea.2014.09.118 ↗
40. On the modelling of residual stresses due to surface peening using eigenstrain distributions10.1243/030932405X30984 ↗
41. Exact reconstruction formulas for plastic strain distribution in the surface-treated plate and their applications10.1007/s00707-020-02625-7 ↗