journal article·2022-05Open access

Mechanical properties of pulsed electric current sintered CrFeNiMn equiatomic alloy

Joonas Lehtonen, Pauli Lehto, Yanling Ge, Aapo Juselius, Simo-Pekka Hannula

Abstract

An equiatomic CrFeNiMn alloy was consolidated using pulsed electric current sintering (PECS) from gas atomized (GA) powder. A range of sintering temperatures was applied to determine its impact on the received microstructure and material properties. It was found that the phase structure of the disc shape sintered samples varied greatly depending on the sintering temperature. According to X-ray diffraction (XRD) the surface of the samples contained a noticeable amount of BCC phase while in the middle of the sample cross sections no BCC phase was found. Ball milling of the gas atomized powder prior to sintering for 25 h increased the density and hardness of the sintered sample from 98.3% to 99% and from 200 HV to 300 HV, respectively. At the same time, the ultimate tensile strength increased from 700 MPa to 1000 MPa and the elongation at fracture decreased from 40% to 25%. The enhanced hardness and tensile strength were attributed to the grain refinement caused by milling the powder prior to sintering. Milling of the powder resulted in a reduction in grain size of the sintered material from 5.7 μm to 1.9 μm when sintered at 1100 °C for 5 min. The grain refinement was also found to affect the deformation mechanisms. While the deformation of the samples prepared directly from GA powder was accommodated by the cell-forming process and deformation twinning, milling refined the initial microstructure to such an extent that deformation twinning was suppressed. In summary, a single phase equiatomic CrFeNiMn alloy can be achieved by pulsed electric current sintering of gas atomized powder. Sintering at temperatures above 1100 °C results in a single-phase FCC structure excluding the surface of the samples. Milling of the starting powder increases the density and strength and decreases the grain size of the sintered material. Decrease in grain size also suppresses deformation twinning and promotes dislocation cell formation. As the CrFeNiMn alloy system does not contain cobalt as an alloying element it shows great promise to be used in nuclear applications. The CrFeNiMn alloy showed good phase stability during tensile testing by not undergoing phase transformation contrary to metastable austenitic stainless steel where martensite transformations take place.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites · High Entropy Alloys Studies · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (55)

Show source-provided references
1. Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
2. Microstructural development in equiatomic multicomponent alloys10.1016/j.msea.2003.10.257 ↗
3. Oxide dispersion strengthened CoCrFeNiMn high-entropy alloy10.1016/j.msea.2017.02.068 ↗
4. Alloying behavior and novel properties of CoCrFeNiMn high-entropy alloy fabricated by mechanical alloying and spark plasma sintering10.1016/j.intermet.2014.08.008 ↗
5. Preparation of superfine-grained high entropy alloy by spark plasma sintering gas atomized powder10.1016/j.intermet.2015.08.012 ↗
6. Consolidation/synthesis of materials by electric current activated/assisted sintering10.1016/j.mser.2008.09.003 ↗
7. Mechanical alloying and milling
8. The cleavage strength of polycrystals
9. The deformation and ageing of mild steel: III discussion of results10.1088/0370-1301/64/9/303 ↗
10. Precipitation hardening in metals10.1179/026708399773002782 ↗
11. Degarmo · 2003 · 67
12. Stacking fault energies in austenitic stainless steels10.1016/j.actamat.2016.03.042 ↗
13. Evolution of dislocation patterns in fcc metals10.1088/1757-899X/3/1/012004 ↗
14. Burke · J. Met. · 1950 · 2 · 1324
15. Transition of twinning behavior in CoCrFeMnNi high entropy alloy with grain refinement10.1016/j.msea.2017.12.022 ↗
16. Microstructure and strengthening mechanisms in an FCC structured single-phase nanocrystalline Co 25 Ni 25 Fe 25 Al 7.5 Cu 17.5 high-entropy alloy10.1016/j.actamat.2016.01.050 ↗
17. The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy10.1016/j.actamat.2013.06.018 ↗
18. Observations of lattice curvature near the interface of a deformed aluminium bicrystal
19. A model of grain fragmentation based on lattice curvature10.1016/j.actamat.2009.11.020 ↗
20. An investigation of surface nanocrystallization mechanism in Fe induced by surface mechanical attrition treatment10.1016/S1359-6454(02)00310-5 ↗
21. Valiev
22. Irradiation resistance mechanism of the CoCrFeMnNi equiatomic high-entropy alloy10.1038/s41598-020-79775-0 ↗
23. Microstructures and mechanical properties of compositionally complex Co-free FeNiMnCr 18 FCC solid solution alloy10.1016/j.msea.2015.05.097 ↗
24. Microstructural stability and mechanical behavior of FeNiMnCr high entropy alloy under ion irradiation10.1016/j.actamat.2016.05.007 ↗
25. Neutron irradiation response of a Co-free high entropy alloy10.1016/j.jnucmat.2019.151838 ↗
26. A fracture-resistant high-entropy alloy for cryogenic applications10.1126/science.1254581 ↗
27. Corrosion and thermal stability of CrMnFeNi high entropy alloy in molten FLiBe salt10.1038/s41598-019-55653-2 ↗
28. Tensile properties of the Cr–Fe–Ni–Mn non-equiatomic multicomponent alloys with different Cr contents10.1016/j.matdes.2015.08.007 ↗
29. Recovery, recrystallization, grain growth and phase stability of a family of FCC-structured multi-component equiatomic solid solution alloys10.1016/j.intermet.2013.10.024 ↗
30. Effect of Co on the phase stability of CrMnFeCoxNi high entropy alloys following long-duration exposures at intermediate temperatures10.1016/j.intermet.2019.106582 ↗
31. Phase structures of gas atomized equiatomic CrFeNiMn high entropy alloy powder10.1016/j.jallcom.2020.154142 ↗
32. Cold gas spraying of a high-entropy CrFeNiMn equiatomic alloy10.3390/coatings10010053 ↗
33. Adaptive domain misorientation approach for the EBSD measurement of deformation induced dislocation sub-structures
34. Boundary identification in EBSD data with a generalization of fast multiscale clustering10.1016/j.ultramic.2013.04.009 ↗
35. Texture analysis with MTEX- Free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
36. IPF coloring of crystal orientation data
37. Characterisation of local grain size variation of welded structural steel10.1007/s40194-016-0318-8 ↗
38. Influence of grain size distribution on the Hall–Petch relationship of welded structural steel10.1016/j.msea.2013.10.094 ↗
39. Lehto
40. Lehto
41. Lehto
42. Lehto
43. Texture analysis with MTEX- Free and open source software toolbox10.4028/www.scientific.net/SSP.160.63 ↗
44. Raghavan · Metall. Mater. Trans. · 1994 · 25A · 267510.1007/BF02649220 ↗
45. Effect of ball milling parameters on the refinement of tungsten powder10.3390/met8040281 ↗
46. Fang · 2010
47. Nucleation and growth of twin interfaces in FCC metals and alloys
48. Strengthening and deformation mechanism of a Fe20Co20Cr20Mn20Ni20 high entropy alloy with high nitrogen content
49. Understanding martensite and twin formation in austenitic steels: a model describing TRIP and TWIP effects10.1016/j.actamat.2017.02.004 ↗
50. The influence of alloying, temperature, and related effects on the stacking fault energy
51. Viewpoint on the formation and evolution of annealing twins during thermomechanical processing of FCC metals and alloys10.1007/s11661-020-05772-7 ↗
52. Selective laser melting of an equiatomic CoCrFeMnNi high-entropy alloy: processability, non-equilibrium microstructure and mechanical property10.1016/j.jallcom.2018.02.298 ↗
53. Correlation of yield strength and tensile strength with hardness for steels10.1007/s11665-008-9225-5 ↗
54. Ab initio assisted design of quinary dual-phase high-entropy alloys with transformation-induced plasticity10.1016/j.actamat.2017.07.023 ↗
55. Strain rate sensitivity of a TRIP-assisted dual-phase high-entropy alloy10.3389/fmats.2018.00030 ↗