journal article·2022-01

Long-term service induced mechanical properties change of hot-end welding metals in a retired CrMoV bainitic gas turbine rotor

Shao-Shi Rui, Qi-Nan Han, Xue Wang, Jia-Min Zhao, Zhipeng Cai, Dong Du, Hui-Ji Shi

Publisher page

Abstract

Abstract This research focused on evaluating the mechanical properties change of Welding Metals (WMs) at the turbine-end (hot-end, working beyond 500 °C) of a retired CrMoV bainitic gas turbine rotor serving over 14 years, by comparison to those WMs at the compressor-end (cold-end, working below 300 °C). After long-term service, the room-temperature elastic modulus and the bainitic microstructure of hot-end WMs stayed almost the same as those of cold-end WMs, but the high-temperature elastic modulus and the dislocations density of the former became higher than those of the latter. The above change, especially the change of high-temperature elastic modulus produced significant influences on the tensile, fatigue and creep behaviors of hot-end WMs, which further led to a higher tensile and creep strength but a lower ductility, as well as a better fatigue crack propagation resistance under high-temperature condition. A correlation between the high-temperature elastic modulus change and the tensile/fatigue/creep behaviors change was established for hot-end WMs based on mechanics modelling, which provided a feasible way to monitor the rotor properties change.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. Near-threshold fatigue crack growth behavior of 10% Cr martensitic steel welded joint with 9% Cr weld metal in high temperature air10.1016/j.ijfatigue.2020.105650 ↗
2. Microstructure and high temperature fracture toughness of NG-TIG welded Inconel 617B superalloy10.1016/j.jmst.2019.07.021 ↗
3. Modeling and simulation of weld residual stresses and ultrasonic impact treatment of welded joints10.1016/j.proeng.2018.02.005 ↗
4. Investigation on the resistance to fatigue crack growth for weld metals with different Ti addition in near-threshold regime10.1016/j.ijfatigue.2018.10.018 ↗
5. Fatigue crack initiation and propagation of different heat affected zones in the presence of a microdefect10.1016/j.ijfatigue.2019.105191 ↗
6. Degradation of mechanical properties of Cr-Mo-V and 2.25Cr-1Mo steel components after long-term service at elevated temperatures10.1007/BF02647496 ↗
7. Effect of long-term Service exposure on microstructure and mechanical properties of a CrMoV steam turbine rotor steel10.1007/BF02646505 ↗
8. Effect of service environment on mechanical properties of 30Cr2Ni4MoV steel for turbine low-pressure rotor
9. Microstructure investigation of Cr-Mo-V steel steam turbine rotor after long-term service
10. Changes in morphology and composition of carbides during cyclic deformation at room and elevated temperature and their effect on mechanical properties of Cr-Mo-V steel10.1016/0001-6160(85)90174-9 ↗
11. Mechanical properties of 30Cr1Mo1V HP-IP rotor steel after long-term service
12. Degradation of mechanical properties of cast Cr-Mo-V and Cr-W-V steam turbine casings after long-term service at elevated temperatures. Part I: tensile properties, brittle fracture strength and Charpy impact properties10.1016/0308-0161(94)90048-5 ↗
13. Fracture toughness behavior of ex-service 2-1/4Cr-1Mo steels from a 22-year-old fossil power plant10.1007/BF02656813 ↗
14. Fracture and fatigue properties of 30Cr1Mo1V rotor after long-term service and its microstructure evolution
15. Evaluation of fracture toughness degradation of CrMoV rotor steels based on ultrasonic nonlinearity measurements10.1007/BF03185165 ↗
16. The influences of impurity content, tensile strength, and grain size on in-service temper embrittlement of CrMoV steels10.1007/BF02666669 ↗
17. Effect of service exposure on fatigue crack propagation of Inconel 718 turbine disc material at elevated temperatures10.1016/j.matchar.2014.06.022 ↗
18. Lemaitre · 1985
19. Physically-based modeling of cyclic softening and damage behaviors for a martensitic turbine rotor material at elevated temperature10.1016/j.ijfatigue.2020.105956 ↗
20. On the elastic modulus degradation in continuum damage mechanics10.1016/S0045-7949(99)00187-X ↗
21. Monitoring low cycle fatigue damage in turbine blade using vibration characteristics10.1016/j.ymssp.2005.02.011 ↗
22. A new coupled approach of residual stiffness and strength for fatigue of fibre-reinforced composites10.1016/S0142-1123(01)00194-3 ↗
23. Elastic properties of heat resistant steels after long-term creep exposure10.3184/096034008X357276 ↗
24. Diffraction-based misorientation mapping: a continuum mechanics description10.1016/j.jmps.2019.103709 ↗
25. In-situ SEM study of short fatigue crack propagation behavior in a dissimilar metal welded joint of nuclear power plant10.1016/j.matdes.2015.08.090 ↗
26. Crystallographic analysis on small fatigue crack propagation behaviour of a nickel‐based single crystal superalloy10.1111/ffe.12465 ↗
27. High temperature in-situ SEM observation and crystal plasticity simulation on fretting fatigue of Ni-based single crystal superalloys10.1016/j.ijplas.2019.102645 ↗
28. The effect of crystal orientation on fretting fatigue crack formation in Ni-based single-crystal superalloys: in-situ SEM observation and crystal plasticity finite element simulation10.1016/j.triboint.2018.01.011 ↗
29. Tada · 2000 · vol. 2 · 1
30. EBSD analysis of cyclic load effect on final misorientation distribution of post-mortem low alloy steel: a new method for fatigue crack tip driving force prediction10.1016/j.ijfatigue.2018.04.016 ↗
31. Low cycle fatigue and cyclic softening behaviour of martensitic cast steel10.1016/j.engfailanal.2013.06.019 ↗
32. Mechanics of fatigue crack propagation by crack-tip plastic blunting10.1016/0013-7944(84)90163-2 ↗
33. The relation between minimum creep rate and time to fracture10.1080/03063453.1976.11683560 ↗
34. Grain size effect on the thermally activated twin boundary migration in a zirconium alloy10.1016/j.msea.2018.03.118 ↗
35. Effect of pre-annealing deformation on thermally activated twin boundary migration in a zirconium alloy10.1016/j.jallcom.2018.01.288 ↗
36. A twin size effect on thermally activated twin boundary migration in a Mg–3Al–1Zn alloy10.1016/j.msea.2015.05.070 ↗
37. Effect of dislocation-twin boundary interaction on deformation by twin boundary migration10.1016/j.msea.2016.03.061 ↗
38. On the ostwald ripening theory10.1016/0001-6160(82)90004-9 ↗
39. Theoretical analysis of the relationship between elastic constants of metals and temperatures
40. A phenomenological explanation of the variation of elastic modulus with temperature for metallic materials
41. Young's modulus of various refractory materials as a function of temperature10.1111/j.1151-2916.1959.tb15462.x ↗
42. Grain boundary damping I: pure iron10.1088/0370-1328/78/6/353 ↗
43. Grain boundary damping II: iron interstitial alloys10.1088/0370-1328/78/6/354 ↗
44. The effects of applied stress on the intergranular phosphorus segregation in a chromium steel10.1016/0001-6160(81)90045-6 ↗
45. Issues concerning the effects of applied tensile stress on intergranular segregation in a low alloy steel10.1016/1359-6454(95)00249-9 ↗
46. Fifty-year study of the Peierls-Nabarro stress10.1016/S0921-5093(97)00184-6 ↗
47. The dislocation distribution, flow stress, and stored energy in cold-worked polycrystalline silver10.1080/14786436008238300 ↗
48. Estimation of the Hall–Petch strengthening coefficient of steels through nanoindentation10.1016/j.scriptamat.2014.05.004 ↗
49. Effect of carbon and nitrogen on the Hall-petch coefficient of ferritic iron (review on the Hall-petch relation in ferritic iron)10.4028/www.scientific.net/MSF.638-642.168 ↗
50. Dislocations and pinning points10.1007/s10948-012-1481-9 ↗
51. The nucleation of cavities by plastic deformation
52. An investigation of cyclic J integral as a driving force for fatigue crack growth
53. Prediction of fatigue crack growth rates: theory, mechanisms, and experimental results10.1179/msc.1977.11.8-9.351 ↗
54. Nix · 1979 · 1503
55. Five-power-law creep in single phase metals and alloys10.1016/S0079-6425(99)00006-7 ↗
56. Creep damage mechanics and micromechanisms10.1016/B978-1-4832-8440-8.50017-X ↗