Novel Fe-0.3Cr-0.4Mo-1.5Mn–3Ni-0.6C tool steel with superior properties under quasi-static and dynamic loading
Source abstract
Abstract
Abstract In the present work, the correlation between microstructure and mechanical behaviour under quasi-static and dynamic loading of a novel designed high strength Fe-0.3Cr-0.4Mo-1.5Mn–3Ni-0.6C tool steel is presented. The alloy was manufactured under elevated cooling rates promoting a fine microstructure composed of martensite and retained austenite already in the as-cast state as detected via electron backscattered diffraction and X-ray diffraction. Due to this phase combination, a high compressive strength of about 3700 MPa combined with a total compressive strain of 24% can be observed as well as a pronounced work hardening. This behaviour was mainly traced back to deformation-induced martensite formation (transformation induced plasticity (TRIP) effect). Tests under dynamic loading conditions at a strain rate of 102 s−1, which are also of high importance for later tool applications, display no significant change regarding the compressive strength and total deformation. Furthermore, an increased compressive yield strength and a pronounced work hardening could be detected under dynamic conditions, which was also attributed to the TRIP effect as for the quasi-static tests. Thereby, a decreasing rate of martensite formation with increasing deformation could be observed for both states. Furthermore, adiabatic shear bands (ASB) were detected in compression samples under dynamic loading via scanning electron microscopy and the failure behaviour was discussed with a focus on adiabatic shearing (also including transmission electron microscopy investigations). Concluding, the newly developed cast Fe-0.3Cr-0.4Mo-1.5Mn–3Ni-0.6C steel shows no significant strain rate sensitivity, which is an outstanding property of cast tool steels.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Enhancing impact fracture toughness and tensile properties of microalloyed cast steel by hot forging and post-forging heat treatment processes10.1016/j.matdes.2012.11.051 ↗
2. Influence of Ni content on impact-abrasion wear resistance of medium-carbon low alloy cast steel10.1088/2053-1591/ab3cef ↗
3. Materials for automotive lightweighting10.1146/annurev-matsci-070218-010134 ↗
4. Effect of boron on cast tungsten-molybdenum high-speed steels
5. Modifying cast tungsten-molybdenum high-speed steels with niobium, zirconium, and titanium10.1007/s11041-005-0031-5 ↗
6. Influence of cutting conditions of cast-metal cutting tools on their wear and durability. Part 2. Durability test results10.3103/S106836660802013X ↗
7. Development of high-speed steels for cast metal-cutting tools10.4028/www.scientific.net/SSP.113.559 ↗
8. Comparison of the microstructure of M2 steel fabricated by continuous casting and with a sand mould10.3390/met9050560 ↗
9. Tool steels for cold working dies10.1007/s11041-006-0076-0 ↗
10. 2.9 heat treatment of tool steels
11. Bryson · 2005
12. Thermomechanical processing of advanced high strength steels10.1016/j.pmatsci.2018.01.006 ↗
13. Keeler · 2015
14. Effects of niobium and heat treatment on microstructure and mechanical properties of low carbon cast steels10.1016/j.matdes.2016.05.057 ↗
15. Superior mechanical properties of FeCrMoVC10.1063/1.2751577 ↗
16. Effect of short-term tempering on microstructure and mechanical properties of high-strength FeCrMoVC10.1016/j.actamat.2012.04.041 ↗
17. Microstructural and mechanical characterization of an ultra-high-strength Fe86.7Cr4.4Mo0.6.V1.1W2.5C4.7 alloy10.1007/s10853-011-5794-z ↗
18. Prediction and experimental validation of micro-milling cutting forces of AISI H13 steel at hardness between 35 and 60 HRC10.1007/s00170-011-3864-7 ↗
19. High strain rate behaviour, transformation-induced plasticity and fracture toughness characterization of cast and additionally tempered Fe85Cr4Mo8V2C1 alloy manufactured using a rapid solidification technique10.1007/s10853-012-6637-2 ↗
20. Transformation-induced plasticity in rapidly solidified Fe88.9Cr4.3V2.2C4.610.1002/srin.201000233 ↗
21. The influence of martensitic transformation on mechanical properties of cast high alloyed CrMnNi-steel under various strain rates and temperatures
22. Influence of reverted austenite on static and dynamic mechanical properties of a PH 13-8 Mo maraging steel10.1016/j.msea.2009.11.046 ↗
23. Study of the effect of grain size on the dynamic mechanical properties of micro-alloyed steels10.1016/j.msea.2008.09.069 ↗
24. Forecast of adiabatic shear band formation in two commercial ultra-high-strength armor steels by split hopkinson pressure bar10.1007/s11661-020-05814-0 ↗
25. Strain-rate-dependent deformation behaviour of high carbon steel in compression: mechanical and structural characterisation10.1007/s10853-018-03301-x ↗
26. A model for the heating due to plastic work10.1016/0093-6413(91)90023-P ↗
27. Large strain mechanical behavior of 1018 cold-rolled steel over a wide range of strain rates10.1007/s11661-003-0188-8 ↗
28. Shear localization in dynamic deformation: microstructural evolution10.1007/s11661-007-9431-z ↗
29. Initiation and growth of microfractures along adiabatic shear bands in Ti-6Al-4V10.1179/mst.1985.1.7.526 ↗
30. Adiabatic shear bands in a Ti-6Al-4V titanium alloy10.1016/S0022-5096(98)00044-1 ↗
31. Shear band formation in 4340 steel: a TEM study10.1016/0167-6636(94)90052-3 ↗
32. A basic approach for strain rate dependent energy conversion including heat transfer effects: an experimental and numerical study10.1016/j.jmatprotec.2006.07.040 ↗
33. Effect of high strain rate on plastic deformation of a low alloy steel subjected to ballistic impact
34. Effect of tempering temperature, plate thickness and presence of holes on ballistic impact behavior and ASB formation of a high strength steel10.1016/j.ijimpeng.2011.12.004 ↗
35. Understanding of adiabatic shear band evolution during high-strainrate deformation in high-strength armor steel10.1016/j.jallcom.2020.155540 ↗
36. High strain-rate fracture and failure of a high strength low alloy steel10.1016/j.msea.2009.07.026 ↗
37. Effect of cooling rate on the microstructure and properties of FeCrVC10.1016/j.jallcom.2015.02.004 ↗
38. A profile refinement method for nuclear and magnetic structures10.1107/S0021889869006558 ↗
39. WinPLOTR: a Windows tool for powder diffraction pattern analysis10.4028/www.scientific.net/MSF.378-381.118 ↗
40. Partial molar volumes from high-temperature lattice parameters of iron-carbon austenite10.1179/msc.1970.4.1.219 ↗
41. Über die Temperaturabhängigkeit der Gitterparameter von Eisen, Kobalt und Nickel im Bereich hoher Temperaturen
42. Spieß · 2005
43. Measurement of residual thermal stress in WC–Co by neutron diffraction10.1016/j.ijrmhm.2008.11.015 ↗
44. The lattice spacings of solid solutions of titanium, vanadium, chromium, manganese, cobalt and nickel in α-iron10.1080/14786441208521140 ↗
45. Atomic radii in crystals10.1063/1.1725697 ↗
46. Lattice parameters of cementite in Fe-C-X (X=Cr, Mn, Mo, and Ni) alloys trans
47. Constitutive modelling of the rate dependent flow stress of cast high-alloyed metastable austenitic TRIP/TWIP steel10.1016/j.msea.2013.11.041 ↗
48. Role of retained austenite on adiabatic shear band formation during high strain rate loading in high-strength bainitic steels10.1016/j.msea.2020.139118 ↗
49. Strain-rate-Dependent deformation behavior and mechanical properties of a multi-phase medium-manganese steel10.3390/met9030344 ↗
50. Ballistic impact behaviour of a tempered bainitic steel against 7.62 mm armour piercing projectile10.14429/dsj.61.411 ↗
51. A comparison of adiabatic shear bands in wrought and additively manufactured 316L stainless steel using nanoindentation and electron backscatter diffraction10.1007/s10853-019-03994-8 ↗
52. Adiabatic shear band development and following failure in 316L fabricated by an additive manufacturing process10.1016/j.msea.2021.141003 ↗
53. Suppression of adiabatic shear band formation by martensitic transformation of retained austenite during split Hopkinson pressure bar test for a high-strength bainitic steel10.1016/j.msea.2021.141127 ↗
54. Formation mechanisms of nanostructures in stainless steel during high-strain-rate severe plastic deformation10.1016/j.msea.2005.08.022 ↗
55. Microstructural evolution in adiabatic shear localization in stainless steel10.1016/S1359-6454(02)00526-8 ↗
56. Model for microstructure evolution in adiabatic shear bands10.1007/s11661-998-0172-4 ↗
57. A review of dynamic recrystallization phenomena in metallic materials10.1016/j.matdes.2016.09.012 ↗
58. Characterization of coarse and ultrafine-grained austenitic stainless steel subjected to dynamic impact load: XRD, SEM, TEM and EBSD analyses10.1016/j.mtla.2018.09.016 ↗
59. The effects of ultra-fine-grained structure and cryogenic temperature on adiabatic shear localization in titanium10.1016/j.actamat.2019.09.011 ↗
60. Dynamic recrystallization in the shear bands of Fe-Cr-Ni monocrystal: electron backscatter diffraction characterization10.1016/j.scriptamat.2007.12.006 ↗
61. On the transition from adiabatic shear banding to fracture10.1016/j.mechmat.2006.03.001 ↗
62. Adiabatic shear banding and cracking phenomena occurring during cold-forging simulation tests of plain carbon steel wire rods by using a split hopkinson's pressure bar10.1007/s12540-015-5252-6 ↗