The effect of hydrogen charging on the evolution of lattice defects and phase composition during tension in 316L stainless steel
Source abstract
Abstract
Abstract The effects of hydrogen charging on the evolution of strain-induced lattice defects and phase transformation were investigated in 316L stainless steel. The initial material was obtained by cold rolling to a thickness reduction of 20%. The surfaces of some of the initial samples were cathodically charged with hydrogen. Afterward, both the charged and uncharged samples were subjected to tension until failure. The dislocation density and twin-fault probability in the charged and uncharged specimens during tension were compared. We found that hydrogen charging reduced the degree of increase in the dislocation density and twin-fault probability during the application of tension to the same strain level. Significant martensitic phase transformation was observed in the uncharged samples tested to the strain of 10% or higher. In the hydrogen-charged samples, only a slight increase in the martensite phase fraction was detected. A correlation between the α′-martensite fraction and the dislocation density was found for the studied samples, suggesting that the lower degree of martensitic phase transformation in the charged 316L steel was caused by the smaller amount of stress developed due to the lower dislocation density. In accordance with the differences observed in the phase composition and defect densities, the hydrogen-charged material exhibited lower surface hardness.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (34)
Show source-provided references
1. Permeability, solubility and diffusivity of hydrogen isotopes in stainless steels at high gas pressures10.1016/j.ijhydene.2006.05.008 ↗
2. Lean-alloyed austenitic stainless steel with high resistance against hydrogen environment embrittlement10.1016/j.msea.2011.06.049 ↗
3. Hydrogen compatibility of austenitic stainless steel tubing and orbital tube welds10.1016/j.ijhydene.2014.03.229 ↗
4. Oxide-induced crack closure: an explanation for near-threshold corrosion fatigue crack growth behavior10.1007/BF02643688 ↗
5. hydrogen embrittlement properties of stainless and low alloy steels in high pressure gaseous hydrogen environment10.2355/isijinternational.52.234 ↗
6. Effects of hydrogen on fatigue crack growth behavior of austenitic stainless steels10.1016/j.ijhydene.2008.02.067 ↗
7. Microstructure of austenitic stainless steels of various phase stabilities after cyclic and tensile deformation10.3139/146.110604 ↗
8. Effects of alloy composition and strain hardening on tensile fracture of hydrogen-precharged type 316 stainless steels10.1016/j.ijhydene.2007.10.046 ↗
9. Effects of hydrogen diffusion on the mechanical properties of austenite 316L steel at ambient temperature10.2320/matertrans.M2010273 ↗
10. Microstructural properties controlling hydrogen environment embrittlement of cold worked 316 type austenitic stainless steels10.1016/j.msea.2015.01.054 ↗
11. Hydrogen uptake in 316L stainless steel: consequences on the tensile properties10.1016/j.corsci.2005.11.004 ↗
12. The effect of hydrogen on the yield and flow stress of an austenitic stainless steel10.1007/BF02669643 ↗
13. Effects of hydrogen concentration on slow crack growth in stainless steels10.1007/BF02647836 ↗
14. Hydrogen softening in the thin plate of microcrystalline 316L stainless steel10.1002/srin.201300082 ↗
15. L. Zhang, B. An, T. Iijima, C. San Marchi, Effect of gaseous hydrogen charging on nanohardness of austenitic stainless steels, in: Proceedings of the ASME 2016 Pressure Vessels and Piping Conference, Vancouver, BC, Canada, 2016, pp. 1–6.10.1115/PVP2016-63390 ↗
16. Hydrogen-enhanced localized plasticity-a mechanism for hydrogen-related fracture10.1016/0921-5093(94)90975-X ↗
17. Hydrogen embrittlement of Ni-Cr-Fe alloys10.1007/s11661-997-0051-4 ↗
18. Stacking fault energies of seven commercial austenitic stainless steels10.1007/BF02641927 ↗
19. Lattice defects dominating hydrogen-related failure of metals10.1016/j.actamat.2008.06.031 ↗
20. Effect of hydrogen on martensite formation in austenitic stainless steels in high-pressure torsion10.1016/j.actamat.2009.03.006 ↗
21. Effect of hydrogen on dislocation structure and strain-induced martensite transformation in 316L stainless steel10.1039/C7RA01053B ↗
22. Mechanical characterisation of microstructural evolution in 304 stainless steel subjected to high-pressure torsion with and without hydrogen pre-charging10.1016/j.msea.2016.03.018 ↗
23. Effects of alloy composition and strain hardening on tensile fracture of hydrogen-precharged type 316 stainless steels10.1016/j.ijhydene.2007.10.046 ↗
24. Correlation between strength and microstructure of ball-milled Al–Mg alloys determined by X-ray diffraction10.1016/j.msea.2004.01.089 ↗
25. The hardness and strength of metals
26. Strengthening via the formation of strain-induced martensite in stainless steels10.1016/j.msea.2003.11.084 ↗
27. Annihilation of dislocations during tensile and cyclic deformation and limits of dislocation densities10.1080/01418617908234871 ↗
28. The effect of hydrogen on vacancy generation in iron by plastic deformation10.1016/j.scriptamat.2006.08.030 ↗
29. Effects of grain size and dislocation density on the susceptibility to high-pressure hydrogen environment embrittlement of high-strength low-alloy steels10.1016/j.ijhydene.2011.10.099 ↗
30. Hydrogen effects on the character of dislocations in high-purity aluminum10.1016/S1359-6454(99)00156-1 ↗
31. Principles of self-annealing in silver processed by equal-channel angular pressing: the significance of a very low stacking fault energy10.1016/j.msea.2009.08.071 ↗
32. Gubicza · 2014
33. Strength and ductility of 316L austenitic stainless steel strengthened by nano-scale twin bundles10.1016/j.actamat.2011.11.009 ↗
34. On the effect of deformation twinning on defect densities10.1016/S0921-5093(97)00023-3 ↗