journal article·2022-01

Influence of solid cohesion on viscous properties in Norton law for aluminum alloys during partial solidification

Yoshihiro Nagata, Ryosuke Takai, Toshimitsu Okane, Muhammad Khairi Faiz, Makoto Yoshida

Publisher page

Abstract

Abstract This study investigated the influence of the solid cohesion, fsc, on the viscous properties (m-value and k-value in the Norton law) for aluminum alloys during partial solidification. In the previous study of Haaften (Mater. Sci. Eng. A, 336 (2002), 1–6), a constitutive model taking into account fsc was proposed as e ˙ = k (T) (σ/fsc (θ,T)) n (=1/m), where θ referred to the dihedral angle at the solid/liquid interface. However, even though it is well known that the m-value decreases with the decreasing temperature in the semi-solid state, the model defined the m-value as a constant to the temperature. Therefore, m = f(fsc) and k = g(fsc) during solidification were clarified in this study. The viscous properties were obtained by tensile tests during partial solidification for Al-5mass%Mg and Al-2mass%Cu alloys. As a result, it was found that the change in the m-value of 0 ≤ fsc
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgical Processes and Thermodynamics · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (39)

Show source-provided references
1. Recent advances in hot tearing during casting of aluminium alloys10.1016/j.pmatsci.2020.100741 ↗
2. Modelling of defects in aluminium cast products
3. Ductility and rheology of an Al-4.5%Cu alloy from room temperature to coherency temperature10.4028/www.scientific.net/MSF.217-222.1209 ↗
4. Tensile properties of as-cast aluminum alloys AA3104, AA6111 and CA31218 at above solidus temperatures10.1016/j.msea.2008.07.027 ↗
5. Mechanical behavior of AA6061 Aluminum in the semisolid state obtained by partial melting and partial solidification10.1007/s11661-010-0268-5 ↗
6. Development of an elasto-viscoplastic constitutive equation for an Al-Mg alloy undergoing a tensile test during partial solidification10.2320/matertrans.L-M2015815 ↗
7. Two-phase modeling of mushy zone parameters associated with hot tearing10.1007/s11661-000-0264-2 ↗
8. Quantification of temperature, stress, and strain fields during the start-up phase of direct chill casting process by using a 3D fully coupled thermal and stress model for AA5182 ingots10.1016/j.msea.2005.02.011 ↗
9. On modelling the interplay between microporosity formation and hot tearing in aluminium direct-chill casting10.1016/j.msea.2005.09.050 ↗
10. Hot tearing criteria evaluation for direct-chill casting of an Al-4.5 pct Cu alloy10.1007/s11661-005-0245-6 ↗
11. Integrated approach for prediction of hot tearing10.1007/s11661-009-9941-y ↗
12. Stress–strain predictions of semisolid Al-Mg-Mn alloys during direct chill casting: effects of microstructure and process variables10.1007/s11663-013-9902-0 ↗
13. High apparent creep activation energies in mushy zone microstructures10.1016/0956-716X(94)90223-2 ↗
14. Rheological behavior of Al-Mg-Si-Cu alloys in the mushy state obtained by partial remelting and partial solidification at high cooling rate10.1007/s11661-006-0090-2 ↗
15. Comparison of mechanical characteristics between semi-liquid state and semi-solid state in Al–Mg alloys10.2464/jilm.61.446 ↗
16. Rheological behavior of the mushy zone at small strains10.1016/S0921-5093(01)01528-3 ↗
17. Rheological behavior of Al-Cu alloys during solidification constitutive modeling, experimental identification, and numerical study10.1007/s11661-005-0244-7 ↗
18. Rheological behavior of a commercial AA5182 aluminum alloy during solidification
19. Tensile behaviour of semi-solid industrial aluminium alloys AA3104 and AA518210.1016/S0921-5093(01)01987-6 ↗
20. Dihedral angle and the equilibrium morphology of grain boundary phases10.1016/0026-0800(71)90018-8 ↗
21. Generalized theory of super-solidus cracking in welds (and castings)
22. Evaluations of ductility characteristics and cracking susceptibility of Al alloys during welding
23. Grain refinement effects on the strain rate sensitivity and grain boundary sliding in partially solidified Al–5wt%Mg alloy10.1016/j.msea.2016.05.023 ↗
24. Prediction and experimental validation of cooling rate dependence of viscoplastic properties in a partially solidified state of Al–5 mass%Mg alloy10.2320/matertrans.L-M2017823 ↗
25. Shear deformation behavior of Al–5%Mg in a semi-solid state10.1016/S1359-6454(98)00330-9 ↗
26. Controlling factor for maximum tensile stress and elongation of aluminum alloy during partial solidification10.2320/matertrans.L-M2019839 ↗
27. Deformation, strength and fracture above the solidus temperature
28. Solute redistribution during solidification with rapid solid state diffusion10.1007/BF02643477 ↗
29. Diffusion of 28Mg in aluminum10.1016/0025-5416(77)90190-2 ↗
30. A new theoretical approach based on the maxwell model to obtain rheological properties of solidifying alloys and its validation10.1007/s11661-017-3998-9 ↗
31. Measurement of viscous properties on Al-5mass%Mg alloy in semi-solid state by tensile test with high-frequency induction heating10.2464/jilm.71.112 ↗
32. Mechanism of high temperature creep of aluminum- magnesium solid solution alloys10.2320/matertrans1960.13.284 ↗
33. Basic creep modelling of aluminium10.1016/j.msea.2017.11.053 ↗
34. Tensile properties of Al–Si–Cu die-casting alloy in the partial solidification state10.2464/jilm.63.253 ↗
35. Tension Characteristics and intercrystalline fractures of Al and ADC-12 at high temperature
36. Mechanical behavior of crystalline solids at elevated temperature10.1016/0079-6425(68)90024-8 ↗
37. The transition from dislocation climb to viscous glide in creep of solid solution alloys10.1016/0001-6160(74)90088-1 ↗
38. Creep characteristics of an Al-2wt.%Cu alloy in the solid solution range
39. Effect of Cu concentration on the high-temperature creep behavior of Al-Cu solid solution alloys10.1016/0921-5093(95)09776-7 ↗