Secondary phase induced cracking initiation of high-speed railway gearbox
Source abstract
Abstract
Abstract High-speed trains have gained a significant influence over the way people live and travel. However, the gearboxes used in high-speed railway vehicles inevitably experience cracking during normal operation, resulting in leakage of the lubrication oil, reduction of the service life, and serious safety hazards. This study investigated the role of secondary-phase particles in crack initiation and propagation in a high-speed railway cast Al gearbox during operation by combining the conventional post-mortem sectional examination and the advanced synchrotron X-ray computed tomography based on in-situ tensile tests. Shrinkage/gas pores increase the stress and act as stress concentrators, and the presence of secondary-phase particles, such as eutectic Si, Fe-rich intermetallic phase, and Mg2Si particles, causes inhomogeneously distributed micro-stress/strain. The soft α-Al matrix accommodates a higher strain, while hard secondary-phase particles accommodate a higher stress. The average volume fraction of eutectic Si is 15.96% at dendritic cell boundaries, which was increased to approximately 24.43% by the presence of blocky secondary-phase particles (Fe-rich intermetallic phase and Mg2Si). The corresponding bulk strain required to fracture the secondary-phase particles at dendritic cell boundaries decreased to 2.93% from 3.42% due to this increase in secondary-phase particle volume fraction. A 16% volume fraction of secondary-phase particles at dendritic cell boundaries is the turning point below which their tendency to fracture during tensile tests decreases significantly.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metallurgy and Material Forming
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (49)
Show source-provided references
1. Fatigue failure analysis of high speed train gearbox housings10.1016/j.engfailanal.2016.12.008 ↗
2. Fatigue crack mechanism study on high-speed EMU gearbox10.3901/JME.2017.02.099 ↗
3. On the fatigue performance of laser hybrid welded high Zn 7000 alloys for next generation railway components10.1016/j.ijfatigue.2016.05.017 ↗
4. Role of secondary phase particles in fatigue behavior of high-speed railway gearbox material10.1016/j.ijfatigue.2019.105336 ↗
5. Porosity and the fatigue behavior of hypoeutectic and hypereutectic aluminum–silicon casting alloys10.1016/j.ijfatigue.2007.08.012 ↗
6. A small-crack growth law and its related phenomena10.1016/0013-7944(92)90297-R ↗
7. A review of modelling small-crack behavior and fatigue-life predictions for aluminum alloys10.1111/j.1460-2695.1994.tb00242.x ↗
8. Statistical distributions for the size of fatigue-initiating defects in Al–7%Si–0.3%Mg alloy castings: a comparative study10.1016/j.msea.2008.06.023 ↗
9. On the size distribution of fracture-initiating defects in Al- and Mg-alloy castings10.1016/j.msea.2007.04.088 ↗
10. Effects of microstructural heterogeneity on fatigue properties of cast aluminum alloys10.1007/s11771-020-4323-0 ↗
11. The deformation and fracture behaviour of an Al-Si-Mg casting alloy10.1016/0921-5093(94)09775-5 ↗
12. Damage by the cracking of silicon particles in an Al-7Si-0.4Mg casting alloy10.1016/1359-6454(95)00172-8 ↗
13. Wang · T. Am. Foundrymen's Soc. · 1998 · 106 · 131
14. The effect of Mg on the microstructure and mechanical behavior of Al-Si-Mg casting alloys10.1007/s11661-999-0301-8 ↗
15. The influence of microstructure on the Bauschinger effect in an Al-Si-Mg casting alloy10.1016/1359-6454(95)00171-6 ↗
16. Fatigue behavior of A356/357 aluminum cast alloys. Part II – effect of microstructural constituents10.1016/S1471-5317(00)00009-2 ↗
17. Damage by eutectic particle cracking in aluminum casting alloys A356/35710.1007/s11661-003-0190-1 ↗
18. An experimental evaluation of fatigue crack growth10.1016/j.engfailanal.2004.04.002 ↗
19. The structural integrity of cast aluminium automotive components subjected to fatigue loads10.4028/www.scientific.net/MSF.331-337.1401 ↗
20. Three dimensional (3D) microstructure-based modeling of interfacial decohesion in particle reinforced metal matrix composites10.1016/j.msea.2012.05.108 ↗
21. 2016
22. Quantitative X-ray tomography10.1179/1743280413Y.0000000023 ↗
23. The imaging of failure in structural materials by synchrotron radiation X-ray microtomography10.1016/j.engfracmech.2017.07.027 ↗
24. X-ray micro-tomography an attractive characterisation technique in materials science10.1016/S0168-583X(02)01689-0 ↗
25. Effect of SiC volume fraction and particle size on the fatigue resistance of a 2080 Al/SiCp composite10.1007/s11661-998-0325-5 ↗
26. Quantifying the effect of porosity on the evolution of deformation and damage in Sn-based solder joints by X-ray microtomography and microstructure-based finite element modeling10.1016/j.actamat.2012.03.048 ↗
27. Improving the tensile ductility of metal matrix composites by laminated structure: a coupled X-ray tomography and digital image correlation study10.1016/j.scriptamat.2017.03.030 ↗
28. Wu · Weld. J. · 2013 · 92 · 64
29. Corner fatigue cracking behavior of hybrid laser AA7020 welds by synchrotron X-ray computed microtomography10.1016/j.msea.2015.11.011 ↗
30. Effect of microstructural features on the failure behavior of hybrid laser welded AA702010.1111/ffe.12838 ↗
31. The complex microstructures in an as-cast Al–Mg–Si alloy10.1016/S0167-577X(99)00141-X ↗
32. Correlation between mechanical properties and amount of dendritic α-Al phase in as-cast near-eutectic Al–11.6% Si alloys modified with strontium10.1016/S0921-5093(01)01949-9 ↗
33. Cyclic plasticity at pores and inclusions in cast Al–Si alloys10.1016/S0013-7944(02)00097-8 ↗
34. Dieter · 1986
35. Fatigue behavior of A356-T6 aluminum cast alloys. Part I. Effect of casting defects10.1016/S1471-5317(00)00008-0 ↗
36. Fatigue crack growth and fracture paths in sand cast B319 and A356 aluminum alloys10.1016/S0921-5093(02)00196-X ↗
37. The fracture mode in Al–Si–Mg casting alloys10.1016/S0921-5093(97)00476-0 ↗
38. Effects of pore position in depth on stress/strain concentration and fatigue crack initiation10.1007/s11661-011-0947-x ↗
39. Microstructural processes of plastic instabilities in strengthened metals10.1016/0079-6425(91)90002-B ↗
40. Intergranular and interphase microstresses10.1016/S1359-0286(00)00019-X ↗
41. Plastic relaxation of the transformation strain energy of a misfitting spherical precipitate: ideal plastic behavior10.1007/BF02655099 ↗
42. The law of mixtures applied to the plastic deformation of two- phase alloys of coarse microstructures10.1007/BF02645206 ↗
43. Stress and strain partition in elastic and plastic deformation of two phase alloys10.1007/BF01184992 ↗
44. Stress-strain partitioning analysis of constituent phases in dual phase steel based on the modified law of mixture10.1016/S1674-4799(09)60070-4 ↗
45. Cavity formation from inclusions in ductile fracture10.1007/BF02672306 ↗
46. Effect of thermal aging on the intergranular stress corrosion cracking susceptibility of type 310S stainless steel10.5006/2544 ↗
47. Stress corrosion cracking susceptibility of thermally-aged Type 310S stainless steels in supercritical water10.1016/j.corsci.2018.01.023 ↗
48. Modeling the effect of particle clustering on the mechanical behavior of SiC particle reinforced Al matrix composites10.1007/s10853-006-0100-1 ↗
49. Distributions of pore size and fatigue weak link strength in an A713 sand cast aluminum alloy10.1016/j.msea.2010.03.104 ↗