Fabrication of a thin open-cell Ni foam sheet with a high specific strength and moderate porosity using severe plastic deformation via differential speed rolling
Source abstract
Abstract
Abstract Differential speed rolling was applied to an open-cell Ni foam. As the roll speed ratio increased, the cell walls were deformed into more curved shape with smaller curvatures. As the roll speed ratio increased, grain refinement in the cell walls (via continuous dynamic recrystallization) was promoted and dislocation density was increased. Porosity decreased after rolling, but it decreased less at a higher roll speed ratio. The porosity decreased from 90% to 25% after conventional rolling, while it decreased to 36% after differential speed rolling with a roll speed ratio of 3. The results herein demonstrate that differential speed rolling with a high roll speed ratio can produce a thin open-cell Ni foam sheet with a high specific strength, high hardness and moderate porosity. The mechanism of the roll speed ratio effect on the cell shape and porosity is discussed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Cellular and Composite Structures · Microstructure and mechanical properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Evaluation of metal foam based thermoelectric generators for automobile waste heat recovery10.1016/j.ijheatmasstransfer.2018.02.029 ↗
2. Overview of porous media/metal foam application in fuel cells and solar power systems10.1016/j.rser.2018.07.032 ↗
3. Size-resolved engine exhaust aerosol characteristics in a metal foam particulate filter for GDI light-duty vehicle10.1016/j.jaerosci.2012.11.002 ↗
4. Damping and sound absorption properties of particle reinforced Al matrix composite foams10.1016/S0266-3538(02)00215-4 ↗
5. Plastic deformation mechanisms in axially compressed metal tubes used as impact energy absorbers10.1016/0020-7403(93)90054-X ↗
6. A review of metal foam and metal matrix composites for heat exchangers and heat sinks10.1080/01457632.2012.659613 ↗
7. Manufacture, characterization and application of cellular metals and metal foams10.1016/S0079-6425(00)00002-5 ↗
8. Deformation processes of porous metlas and metallic foams (review)10.1016/j.mspro.2014.07.614 ↗
9. Strengthening of lotus-type porous copper by ECAE process10.1016/j.jmatprotec.2012.04.024 ↗
10. H. Tsuruoka, H. Utsunomiya, T. Sakai, S. Suzuki, T. Ide, H. Nakajima, Forming of profiled strip from porous metal by rolling. in: Proceedings of the 7th International Conference Porous Metals and Metallic Foams, 2011, pp. 581–585.
11. Accelerated formation of an ultrafine-grained microstructure in closed-cell aluminum foam after extrusion and differential speed rolling10.2320/matertrans.L-M2016838 ↗
12. Compressive behavior of a rolled open-cell aluminum foam10.1016/j.msea.2018.01.015 ↗
13. Three dimensional forming of compressed open-cell metallic foams at elevated temperatures10.1016/j.msea.2015.01.071 ↗
14. Analysis of the elastic properties of open-cell foams with tetrakaidecahedral cells10.1016/S0022-5096(96)00090-7 ↗
15. A general tetrakaidecahedron model for open-celled foams10.1016/j.ijsolstr.2007.10.028 ↗
16. Fabrication of ultrafine-grained Mg-3Al-1Zn magnesium alloy sheets using a continuous high-ratio differential speed rolling technique10.1016/j.msea.2013.11.066 ↗
17. Tensile properties of open-cell nickel foams10.1016/j.matdes.2009.10.018 ↗
18. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
19. Elastic recovery of conical indentations10.1088/0370-1328/78/2/302 ↗
20. Poisson's ratio for metals and alloys10.1179/095066061790425893 ↗
21. Correlation between dislocation density and nanomechanical response during nanoindentation10.1016/j.actamat.2011.11.034 ↗
22. Measurement of mechanical properties by ultra-low load indentation10.1016/S0921-5093(98)00724-2 ↗
23. Young's modulus of electroplated Ni thin film for MEMS applications10.1016/j.matlet.2004.02.044 ↗
24. Crandall · 1979
25. Analysis of thermos-mechanical process occurred in magnesium alloy AZ31 sheet during differential speed rolling10.1016/j.msea.2007.07.089 ↗