Development of a high temperature flow stress model for AerMet 100 covering several orders of magnitude of strain rate
Source abstract
Abstract
Abstract Constant strain rate, constant velocity and Hopkinson Pressure Bar compression tests were carried out on AerMet 100 martensitic steel between 1130 °C and 1250 °C spanning strain rates from 0.01 s−1 to 4000 s−1. The results were used to generate a predictive flow stress model over the entire range of test conditions. The effect of initial austenite grain size on flow stress was found to follow the Hall–Petch relationship. This dependency was then removed through innovative heat treatments. The morphology of the flow stress curves were also dependent on mechanisms of microstructural evolution which were controlled by the test method, strain rate and temperature. Friction and adiabatic heating also had a major contribution. A novel method was proposed in order to define the flow stress, which was then used to determine the work hardening exponent of the Zener–Hollomon equation. It was found that a deviation from the linear trend was observed in Hopkinson Pressure Bar tests and reasons were given. An artificial neural network approach was used to determine a more accurate predictive flow stress model which included the effects of test method, temperature, stain rate and initial austenite grain size. The method showed that it was possible to predict the flow stress between 50 and 2000 s−1 where mechanical testing’s results were absent.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Metallurgy and Material Forming · Microstructure and Mechanical Properties of Steels
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Transmission electron microscopy examination of hardening and toughening phenomena in Aermet 10010.1007/BF02666329 ↗
2. Phase transformations across high strength dissimilar steel inertia friction weld10.1016/j.jmatprotec.2007.10.074 ↗
3. Handbook of Workability and Process Design
4. Review of experimental techniques for high rate deformation and shock studies10.1016/j.ijimpeng.2004.03.005 ↗
5. Effect of strain rate upon plastic flow of steel10.1063/1.1707363 ↗
6. Constitutive analysis in hot working10.1016/S0921-5093(01)01117-0 ↗
7. ASM Handbook Vol.8 Mechanical Testing and Evaluation
8. Development of an experimental facilty for single and multistage constant strain rate compression
9. The effect of tallow concentration on the cold rolling of steel strips10.1016/S0924-0136(03)00461-8 ↗
10. Predicting the critical stress for initiation of dynamic recrystallization10.2355/isijinternational.46.1679 ↗
11. Modelling of dynamic recrystallisation kinetics in austenitic stainless and hypereutectoid steels10.1179/026708306X81478 ↗
12. Initiation of dynamic recrystallization in constant strain rate hot deformation10.2355/isijinternational.43.684 ↗
13. Critical strain for dynamic recrystallization in variable strain rate hot deformation10.2355/isijinternational.43.684 ↗
14. A one-parmenter approach to determining the critical conditions for the initiation of dynamic recrystallization10.1016/1359-6454(95)00146-7 ↗
15. Axisymmetric compression test and hot working properties of alloys10.1179/026708301101510843 ↗
16. ASM Handbook, Volume 08-Mechanical Testing and Evaluation in High Strain Rate Tension and Compression Tests
17. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working10.1016/j.matdes.2010.11.048 ↗
18. Picton · 1994
19. A comparative study on Arrhenius-type constitutive model and artificial neural network model to predict high-temperature deformation behaviour in Aermet100 steel10.1016/j.msea.2011.03.017 ↗
20. Modeling of high temperature rheological behavior of AZ61 Mg-alloy using inverse method and ANN10.1016/j.matdes.2008.03.027 ↗
21. Application of consitutive and neural network models for prediction of high temperature flow behaviour of Al/Mg based nanocomposite10.1016/S1003-6326(13)62656-4 ↗
22. Material characterisation using high-temperature Split Hopkinson pressure bar10.1016/j.jmatprotec.2012.11.008 ↗
23. Technical Datasheet AerMet ® 100 Alloy, 2006
24. Detailed diffraction and electron microscopy study of inertia-friction-welded dissimilar high-strength steels10.1007/s11661-011-0737-5 ↗
25. Carpenter, Technical Datasheet AerMet 100 Alloy.
26. C. Bennett, Inertia Friction Welding of High Strength Aerospace Alloys, Nottingham.
27. High strain rate effects on the strain of alloy steels10.1016/S0924-0136(99)00248-4 ↗
28. Hall–Petch relation and boundary strengthening10.1016/j.scriptamat.2004.06.002 ↗
29. Effect of heat treatment on prior grain size and mechanical property of a maraging stainless steel
30. Effect of microstructure refinement on the strength and toughness of low alloy martensitic steel
31. Metallographic techniques for the determination of the austenite grain size in medium-carbon microalloyed steels10.1016/S1044-5803(01)00142-5 ↗
32. Bramfitt · 2002
33. Petzow · 1978
34. A new method for evaluation of friction in bulk metal forming10.1016/j.jmatprotec.2004.03.029 ↗
35. The adiabatic correction factor for deformation heating during the uniaxial compression test10.1361/105994901770344593 ↗
36. Recrystallization of metals during hot deformation10.1098/rsta.1978.0010 ↗
37. Correcting the stress–strain curve in hot compression process to high strain level10.1007/s11661-009-9783-7 ↗
38. Hall · 2009 · 11
39. Weka [Online]. Available: 〈〈http://www.cs.waikato.ac.nz/ml/index.html〉〉.
40. Neural networks for critical high temperature component life prediction10.1179/026708310X12683157551531 ↗
41. Galushkin · 2007
42. Callister · 2007
43. Formability of TWIP (twinning induced plasticity) automotive sheets10.1016/j.ijplas.2010.03.006 ↗