Laser Beam Direct Energy Deposition of graded austenitic-to-martensitic steel junctions compared to dissimilar Electron Beam welding
Source abstract
Abstract
This article presents the Direct Metal Deposition (DMD) process as a method to build a graded austenitic-to-martensitic steel. Builds are obtained by varying the ratio of the two powders upon DMD processing. Samples with gradual transitions were successfully obtained thanks to the use of a high dilution rate from a layer to another. Long austenitic grains are observed on 316L side when martensitic grains are observed on Fe-9Cr-1Mo side. In the transition zone, the microstructure is mainly martensitic. Characterizations were performed after building and after a tempering heat treatment at 630°C during 8h and compared to dissimilar Electron Beam welds. Before heat treatment, DMD graded area has high hardness values (around 430 HV) due to fresh martensite formed during building. Tempering heat treatment allows reducing hardness in this area to 300 HV. EDS measurements indicate that the chemical gradient between 316L and Fe-9Cr-1Mo obtained by DMD is smoother than the chemical change obtained in Electron Beam (EB) welds. Microstructures in DMD are quite different from those obtained by EB welding. Hardness measurements in DMD samples and in welds exhibit similar behaviours: the weld metal and the Fe-9Cr-1Mo heat affected zone are relatively hard after welding because of fresh martensite, such as the DMD transition zone. These areas are all softened by the tempering heat treatment.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. Some studies on P91 steel and their weldments10.1016/j.jallcom.2018.01.120 ↗
2. Microstructure and mechanical properties of weld fusion zones in modified 9Cr-1Mo steel10.1361/105994901770345033 ↗
3. Study on the fiber laser/TIG weldability of AISI 304 and AISI 410 dissimilar weld10.1016/j.jmapro.2018.08.005 ↗
4. Weldability of dissimilar joint between PNC-FMS and Type 316 steel under electron beam welding
5. Design , fabrication , and characterization of graded transition joints
6. Effect of interlayers and scanning strategies on through-thickness residual stress distributions in additive manufactured ferritic-austenitic steel structure10.1016/j.msea.2018.12.078 ↗
7. Additive manufacturing of functionally graded transition joints between ferritic and austenitic alloys10.1016/j.jallcom.2018.08.197 ↗
8. Additive manufacturing of functionally graded metallic materials using laser metal deposition
9. Residual stresses induced by electron beam welding in a 6061 aluminium alloy10.1016/j.jmatprotec.2016.04.013 ↗
10. A perspective review on experimental investigation and numerical modeling of electron beam welding process10.1016/j.matpr.2017.12.055 ↗
11. Electron beam welding – techniques and trends – Review10.1016/j.vacuum.2016.05.004 ↗
12. Mechanical properties of similar and dissimilar weldments of RAFMS and AISI 316L (N) SS prepared by electron beam welding process10.1016/j.fusengdes.2014.04.063 ↗
13. Improving impact toughness of heavy section reduced activation ferritic martensitic CLF-1 steel joints with electron beam welding10.1016/j.jnucmat.2020.152031 ↗
14. Enhancing the tensile properties of EBM as-built thin parts: effect of HIP and chemical etching10.1016/j.matchar.2018.01.035 ↗
15. Modelling of delta ferrite to austenite phase transformation kinetics in martensitic steels: application to rapid cooling in additive manufacturing10.1016/j.mtla.2021.101157 ↗
16. Heat-treatment effects on a bimetallic additively-manufactured structure (BAMS) of the low-carbon steel and austenitic-stainless steel
17. A comparison on metallurgical behaviors of 316L stainless steel by selective laser melting and laser cladding deposition10.1016/j.msea.2016.12.112 ↗
18. Microstructure and mechanical characteristics of multi-layered materials composed of 316L stainless steel and ferritic steel produced by direct energy deposition10.1016/j.jallcom.2018.09.390 ↗
19. Applying electron backscattering diffraction to macroscopic residual stress characterisation in a dissimilar weld10.1016/j.jmatprotec.2016.11.003 ↗
20. Microstructural evolution of dissimilar welded joints between reduced-activation ferritic-martensitic steel and 316L stainless steel during the post weld heat treatment10.1016/j.msea.2018.03.035 ↗
21. Some studies on P91 steel and their weldments10.1016/j.jallcom.2018.01.120 ↗
22. Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition10.1016/j.jmatprotec.2016.09.005 ↗
23. Additive manufacturing of functionally graded transition joints between ferritic and austenitic alloys10.1016/j.jallcom.2018.08.197 ↗