journal article·2020-11

Room- and elevated-temperature nano-scaled mechanical properties of low-density Ti-based medium entropy alloy

P.H. Lin, J.C. Huang, X.K. Zhang, H.S. Chou, W.S. Chuang, T.Y. Liu, Y.C. Liao, J.S.C. Jang

Publisher page

Abstract

Abstract The incipient plasticity and creep behavior of body-centered cubic (BCC) Ti65(AlCrNb)35 medium entropy alloy (MEA) were investigated via nanoindentation. The elastic modulus and hardness obtained from different methods were compared. The activation volume for plastic deformation was calculated to be 11 b3, indicating a larger-scaled Peierls deformation mechanism typical for BCC metals. The orientation effect on incipient plasticity was studied on (100), (110) and (111) orientations at room temperature. The orientation difference is attributed to the different Schmid factors for different planes. The activation volume and activation energy of dislocation nucleation on Ti65(AlCrNb)35 was estimated as 0.8–0.9 b3 and 0.43 eV, which suggests that the mechanism of incipient plasticity is heterogeneous dislocation nucleation assisted by pre-exist defects, with a very localized activated volume. Also, the activation volume and energy of Ti65(AlCrNb)35 are higher than those of conventional metals (Ni, Pt, Cr and Mg) and lower than those of high entropy alloys (HEAs), which suggests that the dislocation nucleation in Ti65(AlCrNb)35 is more difficult than that in metals but easier than that in HEAs. Creep responses of the (100), (110) and (111) grains at 500–600 °C were found to be all dominated by the power-law dislocation creep mechanism (stress exponent n ~ 5) with the activation energy ~130 kJ/mol. The high stress applied by the indenter tip led to the stress-induced pipe diffusion, assisting the dislocation climb and lowering the activation energy. The activation volume was measured as 3–6 b3, related to dislocation climb and atom diffusion at elevated temperatures. The creep displacements and creep rates for the (100), (110) and (111) planes are quite similar, probably resulting from (i) complex slip systems in BCC structure underneath the indenter tip, (ii) a complex strain field produced by concentrated solute atoms, and (iii) the stress-induced pipe diffusion.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · Metal and Thin Film Mechanics · Intermetallics and Advanced Alloy Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (70)

Show source-provided references
1. Nanostructured high-entropy alloys with multiple principal elements: novel alloy design concepts and outcomes10.1002/adem.200300567 ↗
2. Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys10.1016/j.actamat.2013.01.042 ↗
3. Structure and mechanical properties of a light-weight AlNbTiV high entropy alloy10.1016/j.matlet.2014.11.162 ↗
4. The high temperature tensile and creep behaviors of high entropy superalloy10.1038/s41598-017-13026-7 ↗
5. CoCrFeNiTi-based high-entropy alloy with superior tensile strength and corrosion resistance achieved by a combination of additive manufacturing using selective electron beam melting and solution treatment10.1016/j.matlet.2016.11.026 ↗
6. Microstructure, mechanical and corrosion behaviors of AlCoCuFeNi-(Cr,Ti) high entropy alloys10.1016/j.matdes.2016.12.036 ↗
7. Corrosion of high entropy alloys10.1038/s41529-017-0009-y ↗
8. Mechanism of radiation damage reduction in equiatomic multicomponent single phase alloys10.1103/PhysRevLett.116.135504 ↗
9. Microstructure and wear behavior of AlxCo1.5CrFeNi1.5Tiy high-entropy alloys10.1016/j.actamat.2011.06.041 ↗
10. A high-entropy V35Ti35Fe15Cr10Zr5 alloy with excellent high-temperature strength10.1016/j.matdes.2017.02.029 ↗
11. Design of refractory high-entropy alloys
12. Refractory high-entropy alloys10.1016/j.intermet.2010.05.014 ↗
13. Superplasticity in Ti–6Al–4V: characterisation, modelling and applications10.1016/j.actamat.2015.04.056 ↗
14. Additive manufacturing of titanium alloy for aircraft components10.1016/j.procir.2015.08.061 ↗
15. Mechanical properties and microstructure of laser welded Ti–6Al–2Sn–4Zr–2Mo (Ti6242) titanium alloy10.1016/j.msea.2016.02.068 ↗
16. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
17. Nanoindentation and nanoscratching of hard carbon coatings for magnetic disks10.1557/PROC-383-447 ↗
18. A critical appraisal of the extraction of creep parameters from nanoindentation data obtained at room temperature10.1016/j.actamat.2006.07.020 ↗
19. Creep of nanocrystalline nickel: a direct comparison between uniaxial and nanoindentation creep10.1016/j.scriptamat.2009.10.021 ↗
20. Creep of face-centered-cubic {111} and {100} grains in FeCoNiCrMn and FeCoNiCrMnAl alloys: orientation and solid solution effects10.1016/j.intermet.2018.10.006 ↗
21. Elevated-temperature creep of high-entropy alloys via nanoindentation10.1557/mrs.2019.258 ↗
22. Dislocation nucleation and defect structure during surface indentation10.1103/PhysRevB.58.11085 ↗
23. Effect of orientation and loading rate on the incipient behavior of Ti60(AlCrVNb)40 medium entropy alloy10.1016/j.msea.2020.138969 ↗
24. Activation volume and energy for dislocation nucleation in multi-principal element alloys10.3390/met9020263 ↗
25. Incipient plasticity and dislocation nucleation in body-centered cubic chromium10.1016/j.msea.2014.04.107 ↗
26. Incipient plasticity and dislocation nucleation of FeCoCrNiMn high-entropy alloy10.1016/j.actamat.2013.01.059 ↗
27. Determining the activation energy and volume for the onset of plasticity during nanoindentation10.1103/PhysRevB.73.054102 ↗
28. Quantitative insight into dislocation nucleation from high-temperature nanoindentation experiments10.1038/nmat1429 ↗
29. Dislocation nucleation during nanoindentation in a body-centered cubic TiZrHfNb high-entropy alloy10.1016/j.scriptamat.2016.11.019 ↗
30. Nanomechanical properties of Au (111),(001), and (110) surfaces10.1103/PhysRevB.57.12588 ↗
31. Deformation behavior of Ni3Al single crystals during nanoindentation10.1016/S1359-6454(03)00436-1 ↗
32. Pollock · 1985
33. The relationship between indentation and uniaxial creep in amorphous selenium10.1557/JMR.1995.2024 ↗
34. Prediction of the constitutive equation for uniaxial creep of a power-law material through instrumented microindentation testing and modeling10.2320/matertrans.M2013370 ↗
35. Measurement of power-law creep parameters by instrumented indentation methods10.1016/j.jmps.2012.09.009 ↗
36. A direct comparison of high temperature nanoindentation creep and uniaxial creep measurements for commercial purity aluminum10.1016/j.actamat.2016.03.032 ↗
37. Designing novel lightweight, high-strength and high-plasticity Tix(AlCrNb)100-x medium-entropy alloys10.1016/j.intermet.2019.106673 ↗
38. Surface roughness effects on the displacement bursts observed in nanoindentation10.1557/jmr.2004.19.1.183 ↗
39. Effect of temperature and hydrogen concentration on the lattice parameter of beta titanium10.1016/S0025-5408(01)00604-3 ↗
40. Evaluating elastic properties of a body-centered cubic NbHfZrTi high-entropy alloy – a direct comparison between experiments and ab initio calculations10.1016/j.intermet.2019.04.003 ↗
41. High-entropy alloy: challenges and prospects10.1016/j.mattod.2015.11.026 ↗
42. Plastic anisotropy of γ-TiAl revealed by axisymmetric indentation10.1016/j.actamat.2010.02.025 ↗
43. Defect generation and pileup of atoms during nanoindentation of Fe single crystals10.1103/PhysRevB.67.245405 ↗
44. Dislocation nucleation in bcc Ta single crystals studied by nanoindentation10.1103/PhysRevB.76.165422 ↗
45. Sample size and orientation effects of single crystal aluminum10.1016/j.msea.2016.03.076 ↗
46. A combined experimental-numerical approach for determining mechanical properties of aluminum subjects to nanoindentation10.1038/srep15072 ↗
47. Anisotropy in the hardness of single crystals
48. Measuring the elastic properties of anisotropic materials by means of indentation experiments10.1016/0022-5096(94)90033-7 ↗
49. On the room temperature deformation mechanisms of a TiZrHfNbTa refractory high-entropy alloy10.1016/j.msea.2015.08.024 ↗
50. Extrinsic mechanical size effects in thin ZrNi metallic glass films10.1016/j.actamat.2015.02.038 ↗
51. Johnson · 1987
52. Time-dependent characteristics of incipient plasticity in nanoindentation of a Ni3Al single crystal10.1016/S1359-6454(02)00025-3 ↗
53. A coupled atomistics and discrete dislocation plasticity simulation of nanoindentation into single crystal thin films10.1016/j.actamat.2003.09.011 ↗
54. Atomistic simulations of elastic deformation and dislocation nucleation during nanoindentation10.1016/S0022-5096(02)00119-9 ↗
55. Lattice distortion effect on incipient behavior of Ti-based multi-principal element alloys10.1016/j.jmrt.2020.05.081 ↗
56. Effect of solid solution elements on nanoindentation hardness, rate dependence, and incipient plasticity in fine grained magnesium alloys10.1016/j.actamat.2011.08.047 ↗
57. Incipient plasticity and activation volume of dislocation nucleation for TiZrNbTaMo high-entropy alloys characterized by nanoindentation10.1016/j.jmst.2018.11.014 ↗
58. Crystallographic orientation and indenter radius effects on the onset of plasticity during nanoindentation10.1557/jmr.2012.368 ↗
59. Plastic deformation of nickel under high hydrostatic pressure10.1016/j.jallcom.2004.01.039 ↗
60. Vacancy defect mobilities and binding energies obtained from annealing studies10.1016/0022-3115(78)90247-7 ↗
61. The mechanisms of indentation creep10.1016/0956-7151(91)90043-Z ↗
62. Diffusion in titanium10.2355/isijinternational.31.757 ↗
63. Prediction of high-entropy stabilized solid-solution in multi-component alloys10.1016/j.matchemphys.2011.11.021 ↗
64. The stress and temperature dependence of steady-state flow at intermediate temperatures for pure polycrystalline aluminum10.1016/0001-6160(80)90066-8 ↗
65. Transient creep of Ti–Al–Nb alloys10.1016/S0921-5093(01)01462-9 ↗
66. On measurements of self-diffusion rates along dislocations10.1002/pssb.19700420102 ↗
67. An examination of the breakdown in creep by viscous glide in solid solution alloys at high stress levels10.1016/0001-6160(82)90139-0 ↗
68. Effect of nanocrystalline and ultrafine grain sizes on the strain rate sensitivity and activation volume: fcc versus bcc metals10.1016/j.msea.2004.03.064 ↗
69. Thermal activation mechanisms and Labusch-type strengthening analysis for a family of high-entropy and equiatomic solid-solution alloys10.1016/j.actamat.2016.08.047 ↗
70. Stress-induced solute diffusion along dislocations in dilute copper alloys10.1016/0001-6160(67)90358-6 ↗