journal article·2020-07

On the rate-dependency of mechanical properties and failure mechanisms of a (γ + α2) - TiAl/Ti3Al-Al2O3 cermet

Haoyang Li, Pouyan Motamedi, James David Hogan

Publisher page

Abstract

This study investigated the rate-dependent mechanical properties and failure of a self-propagating high-temperature synthesized TiAl/Ti3Al-Al2O3 cermet using mechanical testing and advanced microscopy. Quasi-static and dynamic uniaxial compression tests coupled with high-speed imaging and digital image correlation were used to determine the rate-dependency of stress-strain behavior, compressive strength, and failure strain. The stress-strain curves in the dynamic experiments exhibited a series of alternating stress relaxation and strain hardening cycles, where a ~ 1.2 times increase in compressive strength from 2780 ± 60 MPa to 3133 ± 265 MPa, and a ~ 1.6 times increase in failure strain from 0.0166 ± 0.0017 to 0.0264 ± 0.0032 were determined with an increase in strain rates from ~ 10−4 s−1 to ~ 103 s−1. It was also found that the cermet exhibits macroscopic surface texturing by examining the high-speed imaging of deformation during testing. Crystalline texturing with profound microstructural evolution in the titanium aluminide phase was found under dynamic loading using microscopy, and this was correlated with the macroscopic surface texturing observed using high-speed imaging and the cyclical stress relaxation and strain hardening behavior in the stress-strain curves. Altogether, this study presents a thorough understanding of the rate-dependency of the TiAl/Ti3Al-Al2O3 cermet with regard to mechanical properties and failure mechanisms and provides insights for modeling and improvement.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced materials and composites · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (100+)

Show source-provided references
1. Effect of confinement on the static and dynamic indentation response of model ceramic and cermet materials10.1016/j.ijimpeng.2016.12.007 ↗
2. Quasistatic and dynamic compression of aluminum-oxide particle reinforced pure aluminum10.1016/S0921-5093(02)00035-7 ↗
3. Comparison of the plastic deformation and failure of A359/SiC and 6061-T6/Al2O3 metal matrix composites under dynamic tension10.1016/j.msea.2004.01.008 ↗
4. Wilkins · 1969
5. Response of aluminium-infiltrated boron carbide cermets to shock wave loading10.1007/BF00376280 ↗
6. Schwarzkopf · 1953
8. Mari · 2014
9. Viscoplastic deformations and compressive damage in an A359/SiCp metal–matrix composite10.1016/S1359-6454(99)00430-9 ↗
10. Impact resistance of TiC-based cermets10.1016/j.ijimpeng.2013.06.008 ↗
11. Rate and microstructure influence on the fracture behavior of cemented carbides WC-Co and WC-Ni10.1007/s10704-017-0237-8 ↗
12. Analyses of metallurgical behavior of Al–SiCp composites after ballistic impacts10.1016/j.compstruct.2003.08.005 ↗
13. Processing of ceramic–metal composites10.1179/1743676111Y.0000000073 ↗
14. Taya · 2016
15. Johnson · 1954
16. Evaluation of tensile, compressive, torsional, transverse, and impact tests and correlation of results for brittle cermets10.6028/jres.061.019 ↗
17. Dynamic mechanical and fracture properties of an infiltrated TiC-1080 steel cermet10.1016/j.ijsolstr.2004.06.027 ↗
18. Dynamic behavior of a boron carbide aluminum cermet: experiments and observations10.1016/0167-6636(90)90014-7 ↗
19. Crouch · 2019
20. Environmental behaviour of intermetallic materials
21. Fabrication and properties of γ-TiAl sheet materials: a review10.1007/s11837-017-2551-z ↗
22. An overview of monolithic titanium aluminides based on Ti3Al and TiAl10.1016/S0254-0584(01)00328-5 ↗
23. Microstructure and deformation of two-phase γ-titanium aluminides10.1016/S0927-796X(97)00018-1 ↗
24. 2016
25. Rosenberg · 2012
26. Weeks · 2005
27. Self-propagating high-temperature synthesis of advanced materials and coatings10.1080/09506608.2016.1243291 ↗
28. Sintering behaviour and microstructures of Ti (Al, O)/Al2O3, Ti3Al (O)/Al2O3 and TiAl (O)/Al2O3 in situ composites10.1016/j.msea.2006.01.030 ↗
29. Microstructure and mechanical properties of in-situ synthesized Al2O3/TiAl composites10.1016/S1000-9361(08)60174-0 ↗
30. Alumina–aluminide alloys (3A) technology: II, modeling of TixAly–Al2O3 composites formation10.1111/j.1151-2916.2000.tb01438.x ↗
31. Production of TiAl (Ti3Al)/Al2O3 nanocomposite10.4028/www.scientific.net/JNanoR.3.7 ↗
32. Synthesis and characterization of TiAl/α-Al2O3 nanocomposite by mechanical alloying10.1016/j.jallcom.2008.12.047 ↗
33. Properties and electronic structures of titanium aluminides–alumina composites from in-situ SHS process10.1016/j.msea.2010.11.039 ↗
34. Effect of Al2O3 particles on mechanical properties of directionally solidified intermetallic Ti–46Al–2W–0.5 Si alloy10.1016/S0921-5093(03)00445-3 ↗
35. Reaction sintering of alumina-aluminide alloys (3A)10.1557/JMR.1996.0364 ↗
36. Reaction synthesis of TiAl-Al2O3 composite10.4028/b-5pk7SH ↗
37. Alumina–Ti aluminide interpenetrating composites: microstructure and mechanical properties10.1016/S0167-577X(03)00090-9 ↗
38. Characterization and mechanical testing on novel (γ+ α2)–TiAl/Ti3Al/Al2O3 cermet10.1016/j.msea.2019.02.039 ↗
39. Damage evolution of hot-pressed boron carbide under confined dynamic compression10.1016/j.ijimpeng.2016.09.008 ↗
40. In situ synchrotron x‐Ray diffraction analysis of phase transformation in epitaxial metastable hcp nickel thin films, prepared via plasma‐enhanced atomic layer deposition10.1002/admi.201800957 ↗
41. Motamedi · ACS Appl. Mater. Interfaces · 2017 · 9 · 2472210.1021/acsami.7b05571 ↗
42. Kolsky · 1963
43. Testing of high‐strength ceramics with the split Hopkinson pressure bar10.1111/j.1151-2916.1993.tb03820.x ↗
44. Static and dynamic compression strength of hot-pressed boron carbide using a dumbbell-shaped specimen10.1007/s10853-017-1210-7 ↗
45. Compressive behavior of high particle content B4C/Al composite at elevated temperature10.1016/S1003-6326(13)62803-4 ↗
46. The compressive properties of 2024Al matrix composites reinforced with high content SiC particles at various strain rates10.1016/j.msea.2007.12.021 ↗
47. The compressive failure of aluminum nitride considered as a model advanced ceramic10.1016/j.jmps.2011.02.003 ↗
48. Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review10.1088/0957-0233/20/6/062001 ↗
49. Schreier · 2009 · vol. 1
50. A review of surface deformation and strain measurement using two-dimensional digital image correlation10.1515/mms-2016-0028 ↗
51. The effect of out-of-plane motion on 2D and 3D digital image correlation measurements10.1016/j.optlaseng.2008.05.005 ↗
52. A practical approach to optimizing the preparation of speckle patterns for digital-image correlation10.1088/0957-0233/25/10/107001 ↗
53. Strain determination of polymeric materials using digital image correlation10.1016/j.polymertesting.2010.01.005 ↗
54. Bias error reduction of digital image correlation using Gaussian pre-filtering10.1016/j.optlaseng.2013.04.009 ↗
55. Static and dynamic mechanical damage mechanisms in TiC-1080 steel cermets10.1016/j.scriptamat.2004.03.021 ↗
56. Texture evolution, phase transformation mechanism and nanohardness of selective laser melted Ti-45Al-2Cr-5Nb alloy during multi-step heat treatment process10.1016/j.intermet.2017.01.016 ↗
57. Investigation of aluminum-based nanocomposites with ultra-high strength10.1016/j.msea.2009.07.067 ↗
58. High temperature deformation behaviour and microstructure of cast in-situ TiAl matrix composite reinforced with carbide particles10.1016/j.jallcom.2019.05.136 ↗
59. Boron carbide: structure, properties, and stability under stress10.1111/j.1551-2916.2011.04865.x ↗
60. Structural transformations in the deuterium-containing intermetallic compound (Ti3Al) D1.2 induced by high-pressure torsion10.1134/S0031918X0906009X ↗
61. Strain-rate dependence of the compressive strength of WC–Co hard metals10.1016/j.msea.2014.06.020 ↗
62. Strain rate-dependent compressive deformation and failure behavior of porous SiC/Ti-based metallic glass composite10.1016/j.msea.2014.04.097 ↗
63. Dynamic deformation behavior of a high reinforcement content TiB2/Al composite at high strain rates10.1016/j.msea.2007.10.037 ↗
64. Dynamic response of ceramic-metal composites: the TiC-Steel system10.1063/1.1530719 ↗
65. The damage mechanics of brittle solids in compression10.1007/BF00878002 ↗
66. The influence of mechanical and microstructural properties on the rate-dependent fracture strength of ceramics in uniaxial compression10.1016/j.ijimpeng.2015.02.007 ↗
67. Response of aluminum nitride (including a phase change) to large strains, high strain rates, and high pressures10.1063/1.1589177 ↗
68. Effect of strain rate on the compressive mechanical behavior of a continuous alumina fiber reinforced ZE41A magnesium alloy based composite10.1016/j.msea.2006.03.028 ↗
69. High strain rate deformation and resultant damage mechanisms in ultrafine-grained aluminum matrix composites10.1016/j.msea.2010.05.092 ↗
70. Maloy · 1995
71. Plastic-flow behavior and microstructural development in a cast alpha-two titanium aluminide10.1007/BF02660872 ↗
72. Flow behavior and processing maps of Ti-44.5 Al-3.8 Nb-1.0 Mo-0.3 Si-0.1 B alloy10.1016/j.jallcom.2016.12.214 ↗
73. Dynamic compressive response of intact and damaged AD995 alumina10.1111/j.1744-7402.2004.tb00177.x ↗
74. The role of dynamic material properties in the performance of ceramic armor10.1111/j.1744-7402.2004.tb00171.x ↗
75. Order of influences on the ballistic resistance of armor ceramics and single crystals10.1016/j.msea.2013.12.101 ↗
76. High rate response and dynamic failure of structural ceramics10.1111/j.1744-7402.2004.tb00176.x ↗
77. High strain rate compression testing of ceramics and ceramic composites
78. Dynamic fracture of ceramics in armor applications10.1111/j.1551-2916.2007.01515.x ↗
79. Quasi-static and high-rate mechanical behavior of aluminum-based MMC reinforced with boron carbide of various length scales10.1016/j.msea.2015.10.064 ↗
80. High strain rate response of A356/Al2O3 aluminum alloy MMCs using ls-dyna10.1016/j.proeng.2017.02.457 ↗
81. Dynamic mechanical response of a 1060 Al/Al2O3 composite10.1007/BF01117611 ↗
82. SEM and TEM characterization of the microstructure of post-compressed TiB2/2024Al composite10.1016/j.micron.2011.10.001 ↗
83. Mechanisms responsible for strain‐rate‐dependent compressive strength in ceramic materials10.1111/j.1151-2916.1981.tb09570.x ↗
84. A scaling law for the dynamic strength of brittle solids10.1016/j.actamat.2013.02.045 ↗
85. Fragmentation of brittle materials at high rates of loading10.1007/BF01124844 ↗
86. Micromechanical modeling of reinforcement fracture in particle-reinforced metal-matrix composites10.1007/BF02648860 ↗
87. Alokesh Pramanik, and Mohammad Nazrul Islam. "Failure mechanisms of nanoparticle reinforced metal matrix composite
88. A continuum model for void nucleation by inclusion debonding10.1115/1.3173064 ↗
89. Microstructural and mechanical properties of dual Ti3AlC2–Ti2AlC reinforced TiAl composites fabricated by reaction hot pressing10.1016/j.ceramint.2014.02.092 ↗
90. Effects of interfacial debonding on the rate-dependent response of metal matrix composites10.1016/j.actamat.2005.07.004 ↗
91. Needleman · 1990 · 21
92. Effects of SiC particulate size on dynamic compressive properties in 7075-T6 Al-SiCp composites10.1016/j.msea.2018.09.082 ↗
93. Investigation on dynamic properties and failure mechanisms of Ti–47Al–2Cr–2Nb alloy under uniaxial dynamic compression at a temperature range of 288 K–773 K10.1016/j.jallcom.2015.07.107 ↗
94. Hot deformation behavior and dynamic recrystallization of a β-solidifying TiAl alloy10.1016/j.msea.2015.11.097 ↗
95. Mechanical properties and microstructure in a fine grained Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy deformed at a high strain rate10.1016/j.msea.2018.08.100 ↗
96. Dynamic recrystallization and texture evolution of Ti-22Al-25Nb alloy during plane-strain compression10.1016/j.jallcom.2018.03.372 ↗
97. Crack opening due to deformation twin shear at grain boundaries in near-γ TiAl10.1016/j.intermet.2006.03.005 ↗
98. Deformation of lamellar TiAl alloys by longitudinal twinning10.1016/j.scriptamat.2016.03.004 ↗
99. An electron microscope study of mechanical twinning and fracture in TiAl alloys10.1080/14786430412331315662 ↗
100. Complex investigation of deformation twinning in γ-TiAl by TEM and neutron diffraction10.1016/j.jmps.2016.05.004 ↗