journal article·2019-05Open access

New heat treatment to improve the mechanical properties of low copper aluminum primary foundry alloy

R. Martinez, I. Guillot, D. Massinon

Abstract

Abstract The purpose of this work is to design a new heat treatment in order to improve the mechanical properties of primary 356 + 0.5 wt%Cu aluminum alloy. This heat treatment combines a multi step solution treatment with a quench and a multi step overaging treatment. It takes advantage of the evolution of the solubility limit of the matrix as a function of temperature in order to allow the appearance of successive precipitation sequences during excessive aging in several stages and leads to an increase in the volume fraction of precipitates. After T64 air quench, T6 air quench, T7 air quench and T7 water quench treatments and overaging 100 h at 150 °C, a secondary precipitation of Al2Cu particles is seen using conventional TEM, mostly after the T7 treatments. This secondary precipitation leads to an increase of the static mechanical properties. This dual-step overaging is then transposed to a dual-step aging T7 heat treatment, with aging 2h at 200 °C and 2h at 170 °C, and further compared to a classic T7 treatment with aging during 4h at 200 °C. Both heat treatments are also modeled using a KWN model. The model captures the secondary supersaturation of the proeutectic α-phase that leads to the secondary precipitation during the dual-step aging treatment. This translates to an increase of the mechanical properties by 6% and 3% for the yield strength and the ultimate tensile strength respectively. The elongation decreases by 33%.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Bauxite Residue and Utilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. An analysis method for nucleation and growth controlled reactions at constant heating rate10.1016/S0040-6031(96)03135-8 ↗
2. Influence of predeformation and ageing of an Al-Zn-Mg alloy - II. Modeling of precipitation kinetics and yield stress10.1016/S1359-6454(98)00296-1 ↗
3. Modelling of non-isothermal transformations in alloys containing a particle distribution10.1016/S1359-6454(99)00435-8 ↗
4. Modelling of the microstructure and strength evolution in Al-Mg-Si alloys during multistage thermal processing10.1016/j.actamat.2004.07.002 ↗
5. Multiscale modeling of θ’ precipitation in Al-Cu binary alloys10.1016/j.actamat.2004.03.001 ↗
6. Modeling of the influence of coarsening on viscoplastic behaviour of a 319 foundry aluminum alloy10.1016/j.msea.2012.07.096 ↗
7. Simulation of the concomitant process of nucleation-growth-coarsening of Al2Cu particles in a 319 foundry aluminum alloy10.1088/0965-0393/23/4/045012 ↗
8. Stabilizing effect of alloying elements on metastable phases in cast aluminum alloys by CALPHAD calculations
9. Ovono-Ovono · 2004
10. Reaction kinetics in processes of nucleation and growth
11. Uber die Struktur der bei der Aushärtung einer Aluminium-Kupfer-Legierung auftretenden Zustande
12. The structure of GP1 zones in Al-1,7% at. Cu10.1016/0001-6160(81)90058-4 ↗
13. Kinetics of phase change I - General theory10.1063/1.1750380 ↗
14. Kinetics of phase change II - transformation-time relations for random distribution of nuclei10.1063/1.1750631 ↗
15. Kinetics of phase change III - granulation, phase change and microstructure10.1063/1.1750872 ↗
16. Structural ageing characteristics of binary aluminium-copper alloys
17. The growth of dispersed precipitates in solution10.1016/0001-6160(56)90060-8 ↗
18. The kinetics of precipitation from supersaturated solid solutions
19. Mechanisms of formation of θ and dissolution of θ’ precipitates in an Al-4% Cu alloy10.1016/0001-6160(66)90298-7 ↗
20. An electron microscope investigation of the interfacial structure of semi-coherent precipitates10.1080/14786436808223031 ↗
21. The coarsening behaviour of θ″ and θ′ precipitates in two Al-Cu alloys10.1016/0001-6160(71)90076-9 ↗
22. The orientation and shape of θ precipitates formed in Al-Cu alloy10.1002/pssb.19670200235 ↗
23. Impurity diffusion in aluminium
24. Comments on a comparison of early and recent work on the effect of trace additions of Cd, in or Sn on nucleation and growth of θ’ in al-cu alloys10.1016/S1359-6462(02)00003-9 ↗
25. The microstructure and precipitation kinetics of a cast aluminium alloy10.1016/j.scriptamat.2006.03.065 ↗
26. Interpretation of tensile results by means of quality index and probable yield strength