journal article·2012-01

The effect of extrusion and high-pressure torsion on the properties of Alumix-231

Ismail Ozdemir, Ceren Gode, Hakan Yilmazer, Hasan Callioglu

Publisher page

Abstract

Abstract The mechanical properties and microstructure of commercial Al–15Si–2.5Cu–0.5Mg (Alumix-231 ® ) alloy was subjected to extrusion (EXTR), hot extrusion into rods at 565 °C at an extrusion ratio of 4:1 and high-pressure torsion (HPT) processing, one of the most severe plastic deformation (SPD) techniques, with an anvil rotation speed of 0.5 rpm under a quasi-hydrostatic pressure of 5 GPa. Afterwards, the microstructures of specimens were systematically investigated using XRD, SEM, EBSD, and TEM. Also, tensile properties of Alumix-231 processed by EXTR and HPT were determined at room temperature. The HPT specimen shows refined microstructure (around average 165 nm) having more spherical and homogeneously distributed eutectic silicon second phases in Al metal matrix as compared to EXTR specimen. The hardness values are greater on the surface of the HPT specimen (239.1 Hv) as compared to that EXTR specimen (71.2 Hv) and increase with distance from the center of HPT specimen (198.3 Hv). Tensile strength and ductility of HPT specimen increased approximately 2 times than that of EXTR sample, respectively. The results indicate that the morphological changes in eutectic silicon especially after HPT play a critical role in enhancing or limiting the overall properties of the Alumix-231 material.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Aluminum Alloy Microstructure Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Zhilyaev · Prog. Mater. Sci. · 2008 · 53 · 89310.1016/j.pmatsci.2008.03.002 ↗
2. Azushima · CIRP Ann. – Manuf. Technol. · 2008 · 57 · 71610.1016/j.cirp.2008.09.005 ↗
3. Ito · Mater. Sci. Eng. A · 2009 · 503 · 3210.1016/j.msea.2008.03.055 ↗
4. Valiev · Prog. Mater. Sci. · 2000 · 45 · 10310.1016/S0079-6425(99)00007-9 ↗
5. Venkateswarlu · Rev. Adv. Mater. Sci. · 2010 · 25 · 99
6. Sakai · Mater. Sci. Eng. A · 2005 · 393 · 34410.1016/j.msea.2004.11.007 ↗
7. Xu · Acta Mater. · 2007 · 55 · 20310.1016/j.actamat.2006.07.029 ↗
8. Sabirov · Metall. Mater. Trans. A · 2005 · 36 · 286110.1007/s11661-005-0281-2 ↗
9. Ma · Mater. Sci. Eng. A · 2005 · 395 · 7010.1016/j.msea.2004.12.038 ↗
10. Ma · Acta Mater. · 2005 · 53 · 21110.1016/j.actamat.2004.09.017 ↗
11. Cepeda-Jimenez · J. Alloys Compd. · 2011 · 509 · 63610.1016/j.jallcom.2010.09.122 ↗
12. Rajinikanth · Mater. Sci. Eng. A · 2011 · 528 · 170210.1016/j.msea.2010.10.102 ↗
13. Zhilyaev · Scripta Mater. · 2007 · 57 · 76310.1016/j.scriptamat.2007.06.029 ↗
14. Lu · Mater. Sci. Eng. A · 1998 · 252 · 20310.1016/S0921-5093(98)00676-5 ↗
15. Xu · Mater. Trans. · 2010 · 51 · 210.2320/matertrans.MB200910 ↗
16. Furukawa · Acta Mater. · 1996 · 44 · 461910.1016/1359-6454(96)00105-X ↗
17. Basavakumar · Mater. Charact. · 2008 · 59 · 28310.1016/j.matchar.2007.01.011 ↗
18. Edalati · Scripta Mater. · 2010 · 63 · 17410.1016/j.scriptamat.2010.03.048 ↗
19. Xu · J. Mater. Sci. · 2008 · 43 · 728610.1007/s10853-008-2624-z ↗
20. Zhang · Mater. Sci. Eng. A · 2010 · 527 · 347210.1016/j.msea.2010.02.016 ↗
21. Edalati · Scripta Mater. · 2011 · 64 · 88010.1016/j.scriptamat.2011.01.023 ↗
22. Kucukomeroglu · Mater. Des. · 2010 · 31 · 78210.1016/j.matdes.2009.08.004 ↗