Microstructure and high-temperature mechanical properties of RAFM steel processed by friction stir processing combined with tempering heat treatment
Source abstract
Abstract
Abstract In this study, the microstructure and high-temperature mechanical properties of a 9Cr-1.5W reduced activation ferritic/martensitic (RAFM) steel processed by friction stir processing (FSP) combined with a tempering treatment were investigated. During the FSP, lath martensite microstructures containing needle-like M3C and nano-sized MX precipitates were formed in the steel owing to the severe plastic deformation and high cooling rate. The steel subjected to FSP and the tempering treatment at 700 °C for 60 min (FSP-T60) had a fine-grained microstructure consisting of ferrite and martensite, and a large number of M23C6 precipitates formed at the grain boundaries and within the grains. The FSP-T60 steel showed an increase of ∼100 MPa in the tensile strength at 600 °C and a high elongation of 26% as compared to the steel prepared via traditional hot rolling, normalizing, and tempering. The FSP-T60 steel also exhibited improved creep resistance with a creep rupture time of 4523 h at 600 °C/210 MPa. The increase in the strength and ductility of the steel can be attributed to its refined grain structure and the high density and dispersion of the M23C6 precipitates. Meanwhile, the homogeneous distribution and refinement of M23C6 carbides could reduce the growth rate of the Laves phase during creep, thus extending the formation time of the creep cavities and cracks and further increasing the creep rupture time of the steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (50)
Show source-provided references
1. Improvement of reduced activation 9%Cr steels by ausforming10.1016/j.nme.2015.12.001 ↗
2. Effect of boron on microstructure and creep strength of advanced ferritic power plant steels10.1016/j.proeng.2011.04.018 ↗
3. Coarsening of precipitates in an advanced creep resistant 9% chromium steel—quantitative microscopy and simulations10.1016/S0921-5093(01)01874-3 ↗
4. Evolution of dislocation density, size of subgrains and MX-type precipitates in a P91 steel during creep and during thermal ageing at 600°C for more than 100,000h10.1016/j.msea.2010.03.010 ↗
5. Development of India-specific RAFM steel through optimization of tungsten and tantalum contents for better combination of impact, tensile, low cycle fatigue and creep properties10.1016/j.jnucmat.2013.03.073 ↗
6. Strengthening a fine-grained low activation martensitic steel by nanosized carbides10.1016/j.msea.2019.138471 ↗
7. Microstructure and tensile properties of a 14Cr ODS ferritic steel10.1016/j.msea.2016.10.118 ↗
8. Modeling of structural hardening in oxide dispersion-strengthened (ODS) ferritic alloys10.1007/s10853-015-9566-z ↗
9. Effect of MX type particles on creep strength of ferritic steel10.1016/S0022-3115(03)00281-2 ↗
10. Development of new nano-particle-strengthened martensitic steels10.1016/j.scriptamat.2005.04.019 ↗
11. Effect of thermo-mechanical treatment on tensile properties of reduced activation ferritic-martensitic steel10.1016/j.msea.2018.03.080 ↗
12. Microstructure modification and mechanical property improvement of reduced activation ferritic/martensitic steel by severe plastic deformation10.1016/j.msea.2017.11.095 ↗
13. Microstructural and mechanical characteristics of EUROFER’97 processed by equal channel angular pressing10.1016/j.jnucmat.2010.12.046 ↗
14. On the contribution of carbides and micrograin boundaries to the creep strength of tempered martensite ferritic steels10.1016/j.actamat.2006.08.046 ↗
15. On the effect of equal-channel angular pressing on creep of tempered martensite ferritic steels10.1016/j.msea.2007.02.154 ↗
16. Ductilization of aluminium alloy 6056 by friction stir processing10.1016/j.actamat.2017.01.047 ↗
17. Microstructure evolution and superelastic behavior in Ti-35Nb-2Ta-3Zr alloy processed by friction stir processing10.1016/j.actamat.2017.03.079 ↗
18. A framework for shear driven dissolution of thermally stable particles during friction stir welding and processing10.1016/j.msea.2016.10.015 ↗
19. Friction stir processing of spark plasma sintered aluminum matrix composites with bimodal micro- and nano-sized reinforcing Al2O3 particles10.1016/j.jmapro.2018.03.013 ↗
20. Enhanced mechanical properties of as-cast Mg-Al-Ca magnesium alloys by friction stir processing10.1016/j.matlet.2021.129880 ↗
21. Friction stir processing of dual phase steel: microstructural evolution and mechanical properties10.1016/j.matchar.2019.109787 ↗
22. Effect of microstructures to tensile and impact properties of stir zone on 9%Cr reduced activation ferritic/martensitic steel friction stir welds10.1016/j.msea.2018.05.043 ↗
23. Constitutive analysis to predict high-temperature flow stress in modified 9Cr-1Mo (P91) steel10.1016/j.matdes.2009.08.012 ↗
24. Simple constitutive equations for steel at high temperature10.1007/BF02675567 ↗
25. Progress in development of China Low Activation Martensitic steel for fusion application10.1016/j.jnucmat.2007.03.153 ↗
26. Tempering behavior of 4.5Cr-2W-0.25V steel10.1016/S1006-706X(10)60184-7 ↗
27. Investigation on the precipitation behavior of M3C phase in T91 ferritic steels10.1016/j.nucengdes.2011.04.039 ↗
28. Development of new generation reduced activation ferritic-martensitic steels for advanced fusion reactors10.1016/j.jnucmat.2016.05.037 ↗
29. Effect of thermal ageing on microstructure, tensile and impact properties of reduced activated ferritic-martensitic steel10.1016/j.msea.2017.01.030 ↗
30. Effect of silicon on the microstructure and mechanical properties of reduced activation ferritic/martensitic steel10.1016/j.jnucmat.2015.01.004 ↗
31. Effect of tungsten on tensile properties and flow behaviour of RAFM steel10.1016/j.jnucmat.2012.10.040 ↗
32. Influence of strain rate and temperature on tensile properties and flow behaviour of a reduced activation ferritic–martensitic steel10.1016/j.jnucmat.2012.02.020 ↗
33. Oxide dispersion-strengthened steels: a comparison of some commercial and experimental alloys10.1016/j.jnucmat.2005.01.017 ↗
34. Influence of Laves phase on creep strength of modified 9Cr-1Mo steel10.1016/j.msea.2017.08.111 ↗
35. An investigation of microstructural evolution in electron beam welded RAFM steel and 316LN SS dissimilar joint under creep loading conditions10.1016/j.msea.2018.11.046 ↗
36. Improving strength and ductility of low activation martensitic (LAM) steel by alloying with titanium and tempering10.1016/j.msea.2020.140152 ↗
37. Effect of tempering temperature on the stress rupture properties of Grade 92 steel10.1016/j.msea.2015.05.062 ↗
38. Evolution of creep behavior of CLAM steel after thermal aging at 550 °C10.1016/j.jnucmat.2018.07.002 ↗
39. Improvement of high-temperature mechanical properties of low-carbon RAFM steel by MX precipitates10.1007/s40195-018-0703-y ↗
40. Influence of Ti addition on the microstructure and mechanical properties of a 5% Cr–Mo–V steel10.1016/j.jallcom.2014.12.040 ↗
41. The evolution of mechanical property change in irradiated austenitic stainless steels10.1016/0022-3115(93)90129-M ↗
42. Improvement of high-temperature mechanical properties of low-carbon RAFM steel by MX precipitates10.1007/s40195-018-0703-y ↗
43. Coarsening of Laves phase and creep behaviour of a Re-containing 10% Cr-3% Co-3% W steel10.1016/j.msea.2021.141137 ↗
44. On the microstructural origin of premature failure of creep strength enhanced martensitic steels10.1016/j.jmst.2021.03.001 ↗
45. The kinetics of precipitation from supersaturated solid solutions10.1016/0022-3697(61)90054-3 ↗
46. Effect of Nb precipitate coarsening on the high temperature strength in Nb containing ferritic stainless steels10.1016/j.msea.2005.01.030 ↗
47. Effect of precipitate evolution on creep damage of reduced activation ferritic/martensitic steel friction stir welded joint10.1016/j.jallcom.2019.151738 ↗
48. Effect of M3C on the precipitation behavior of M23C6 phase during early stage of tempering in T91 ferritic steel10.1002/srin.201100153 ↗
49. Mechanism of diffusion promotion of carbon atoms during carburization of 20Cr2Ni4A alloy steel after lanthana-bearing supersonic fine particle bombarding pretreatment10.1016/j.surfcoat.2021.127702 ↗
50. Grain refinement progress of pure titanium during laser shock forming (LSF) and mechanical property characterizations with nanoindentation10.1016/j.msea.2012.11.087 ↗