journal article·2020-11

Cyclic deformation behavior of steels with a nanolamellar microstructure and tensile strength of 1500 MPa

Jiali Zhao, Fucheng Zhang, Chen Chen, Mingming Wang, Shule Xia, Bo Lv

Publisher page

Abstract

Abstract An attempt is made to obtain a nanolamellar microstructure in common metallic engineering materials, including austenite, pearlite, bainite, and martensite steels, by alloying and tailoring process parameters. The tensile strength of all four steels is 1500 MPa. On the basis of the tensile and impact deformation behaviors, the cyclic deformation behaviors of the steels with nanolamellar microstructures are studied using the crystallographic phase as the critical factor. Results indicate that the cyclic stress amplitude of the steels with a nanolamellar microstructure depends on the yield and tensile strengths. The change in the dislocation mobility of the steels with a nanolamellar microstructure results in cyclic hardening during the initial cyclic deformation stage. The fatigue life, which is not indicated by the tensile properties, is mainly affected by the initiation and propagation of fatigue cracks. The hard, brittle cementite lamellae accelerate the initiation and propagation of fatigue cracks, thus deteriorating the fatigue properties of the steels with a nanolamellar microstructure. In contrast, film-like retained austenite effectively suppresses the initiation and propagation of fatigue cracks, extending the fatigue life.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels · Surface Treatment and Residual Stress

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (76)

Show source-provided references
1. Development of and perspective on high-performance nanostructured bainitic bearing steel10.1016/j.eng.2018.11.024 ↗
2. Influence of martensite/austenite interfaces on bainite formation in low-alloy steels below Ms10.1016/j.actamat.2020.02.003 ↗
3. High-resolution characterization of the martensite-austenite constituent in a carbide-free bainitic steel10.1016/j.matchar.2018.07.011 ↗
4. Fatigue behavior of bainitic and martensitic super clean Cr-Si high strength steels10.1016/j.ijfatigue.2013.12.007 ↗
5. Low cycle fatigue behavior of a multiphase microalloyed medium carbon steel: comparison between ferrite-pearlite and quenched and tempered microstructures10.1016/S0921-5093(02)00511-7 ↗
6. High-cycle fatigue behavior of low-C medium-Mn high strength steel with austenite-martensite submicron-sized lath-like structure10.1016/j.msea.2018.01.110 ↗
7. Research and development of heat-resistant materials for advanced USC power plants with steam temperatures of 700 ° and above10.15302/J-ENG-2015031 ↗
8. Hardening and softening mechanisms in a nanolamellar austenitic steel induced by electropulsing treatment10.1016/j.msea.2017.12.011 ↗
9. Effects of ausforming temperature on bainite transformation kinetics, microstructures and mechanical properties in ultra-fine bainitic steel10.1016/j.jmrt.2019.11.085 ↗
10. Microstructural evolution and performance change of a carburized nanostructured bainitic bearing steel during rolling contact fatigue process10.1016/j.msea.2018.04.015 ↗
11. Changes in the mechanical properties of a pearlitic steel due to large shear deformation10.1016/j.msea.2006.09.026 ↗
12. Effect of pre-deformation mode on the microstructures and mechanical properties of Hadfield steel10.1016/j.msea.2018.11.088 ↗
13. Heterogeneous nanostructure developed in heavily cold-rolled stainless steels and the specific mechanical properties10.1016/j.scriptamat.2017.02.016 ↗
14. Effect of microstructure on fatigue behavior of advanced high strength steels produced by quenching and partitioning and the role of retained austenite10.1016/j.msea.2015.06.034 ↗
15. Strain-controlled fatigue behavior of cold-drawn type 316 austenitic stainless steel at room temperature10.1016/j.matchar.2016.08.031 ↗
16. Further improvement in ductility induced by the refined hierarchical structures of pearlite10.1016/j.msea.2018.12.069 ↗
17. Effect of chemical composition and microstructure on the fatigue crack growth resistance of pearlitic steels for railroad application10.1016/j.ijfatigue.2018.10.016 ↗
18. Effect of interlamellar spacing on fracture toughness of nano-structured pearlite10.1016/j.msea.2017.08.115 ↗
19. Micro- and macro-approach to the fatigue crack growth in progressively drawn pearlitic steels at different R-ratios
20. A low-alloy high-carbon martensite steel with 2.6 GPa tensile strength and good ductility10.1016/j.actamat.2018.07.060 ↗
21. An investigation on the microstructure and mechanical properties in an ultrafine lamellar martensitic steel processed by heavy warm rolling and tempering10.1016/j.msea.2018.06.073 ↗
22. Cyclic deformation behaviors of a high strength carbide-free bainitic steel10.1016/j.matdes.2016.01.024 ↗
23. Enhancing both strength and ductility of low-alloy transformation-induced plasticity steel via hierarchical lamellar structure10.1016/j.scriptamat.2020.03.029 ↗
24. Segregation stabilizes nanocrystalline bulk steel with near theoretical strength10.1103/PhysRevLett.113.106104 ↗
25. Microstructure and mechanical properties of a CoFeNi2V0.5Nb0.75 eutectic high entropy alloy in as-cast and heat-treated conditions10.1016/j.jmst.2015.08.006 ↗
26. Exploring the fatigue strength improvement of Cu-Al alloys10.1016/j.actamat.2017.11.019 ↗
27. Fatigue crack growth behaviour in single-colony lamellar structure of Ti-6Al-4V10.1016/j.scriptamat.2019.02.029 ↗
28. On the data-driven materials innovation infrastructure10.1016/j.eng.2020.04.004 ↗
29. Low-cycle fatigue behaviors of pre-hardening Hadfield steel10.1016/j.msea.2017.03.107 ↗
30. Effects of high-temperature deformation and cooling process on the microstructure and mechanical properties of an ultrahigh-strength pearlite steel10.1016/j.matdes.2016.10.049 ↗
31. Bhadeshia · 2015
32. Inconsistent effects of austempering time within transformation stasis on monotonic and cyclic deformation behaviors of an ultrahigh silicon carbidefree nanobainite steel10.1016/j.msea.2019.01.100 ↗
33. Effect of tempering on the microstructure and mechanical properties of a medium carbon bainite steel10.1016/j.msea.2017.01.044 ↗
34. Powder metallurgical nanostructured medium carbon bainitic steel: kinetics, structure, and in situ thermal stability studies10.1016/j.msea.2012.06.043 ↗
35. Dislocation densities in some annealed and cold-worked metals from measurements on the X-ray Debye-Scherrer spectrum10.1080/14786435608238074 ↗
36. On the mechanism of formation of diffusional plate-shaped transformation products10.1016/j.actamat.2005.10.049 ↗
37. Solubility of carbon in tetragonal ferrite in equilibrium with austenite10.1016/j.scriptamat.2012.10.017 ↗
38. In-situ observation of tensile deformation and retained austenite transformation behaviors in carbide-free bainitic steel10.1016/j.msea.2019.138637 ↗
39. In-situ observation of strain partitioning and damage development in continuously cooled carbide-free bainitic steels using micro digital image correlation10.1016/j.msea.2019.04.098 ↗
40. Role of microstructure in the low cycle fatigue of multi-phase steels10.1016/j.msea.2011.11.071 ↗
41. Effects of austempering temperature on bainitic microstructure and mechanical properties of a high-C high-Si steel10.1016/j.msea.2018.11.004 ↗
42. Effect of microstructure on non-linear behavior of ultrasound during low cycle fatigue of pearlitic steels10.1016/j.msea.2010.12.078 ↗
43. Low cycle fatigue behavior in a medium-carbon carbide-free bainitic steel10.1016/j.msea.2016.03.077 ↗
44. Low-cycle fatigue behavior and microstructural evolution in a low-carbon carbide-free bainitic steel10.1016/j.matdes.2015.06.172 ↗
45. Strain energy based low cycle fatigue damage analysis in a plain C-Mn rail steel10.1016/j.msea.2017.09.035 ↗
46. Low-cycle fatigue behaviour and microstructural evolution of pearlitic and bainitic steels10.1016/j.msea.2019.01.043 ↗
47. Low cycle fatigue and cyclic softening behaviour of martensitic cast steel10.1016/j.engfailanal.2013.06.019 ↗
48. Microstructural response on the room temperature low cycle fatigue behaviour of two high strength duplex ferrite-martensite steels and a normalised ferrite-pearlite steel10.1016/j.ijfatigue.2005.06.024 ↗
49. Effect of Mn content on low-cycle fatigue behaviors of low-carbon bainitic steel10.1016/j.msea.2017.04.089 ↗
50. Low-cycle fatigue behaviour of 34CrNiMo6 high strength steel10.1016/j.tafmec.2012.02.004 ↗
51. Tensile and low-cycle fatigue properties of Mg-2.8% Al-1.1% Zn-0.4% Mn alloy along the transverse and rolling directions10.1016/j.scriptamat.2009.07.023 ↗
52. Sliding wear and low cycle fatigue properties of new carbide free bainitic rail steel10.1179/1743284713Y.0000000474 ↗
53. Low cycle fatigue properties and microstructure of P92 ferritic-martensitic steel at room temperature and 873 K10.1016/j.matchar.2019.109923 ↗
54. Understanding strain controlled low cycle fatigue response of P91 steel through experiment and cyclic plasticity modeling10.1016/j.fusengdes.2018.11.007 ↗
55. Room temperature low cycle fatigue behaviour of two high strength lamellar duplex ferrite–martensite (DFM) steels10.1016/j.ijfatigue.2004.09.003 ↗
56. Improvement of low-cycle fatigue resistance in AISI 4140 steel by annealing treatment10.1016/j.ijfatigue.2019.04.020 ↗
57. New method for evaluation of the Manson-Coffin-Basquin and Ramberg-Osgood equations with respect to compatibility
58. High-cycle bending fatigue behaviour of nanostructured bainitic steel10.1016/j.scriptamat.2011.11.033 ↗
59. A study of bainitic nodular cast iron for grinding balls
60. Microstructure and mechanical properties of a low carbon carbide-free bainitic steel co-alloyed with Al and Si10.1016/j.matdes.2012.02.053 ↗
61. Dislocation velocities, dislocation densities, and plastic flow in lithium fluoride crystals10.1063/1.1735121 ↗
62. A brief history of dislocation theory10.1007/BF02670413 ↗
63. Caillard · 2003
64. Effect of grain and twin boundaries on the hardening mechanisms of twinning-induced plasticity steels10.1016/j.scriptamat.2007.10.050 ↗
65. Strengthening materials by engineering coherent internal boundaries at the nanoscale10.1126/science.1159610 ↗
66. Computer-aided three-dimensional visualization of twisted cementite lamellae in eutectoid steel10.1016/j.actamat.2008.08.017 ↗
67. Nucleation of austenite from pearlitic structure in an Fe-0.6C-1Cr alloy10.1016/j.scriptamat.2008.11.041 ↗
68. Bhadeshia · 2018
69. On the crystallographic characteristics of nanobainitic steel10.1016/j.actamat.2017.01.058 ↗
70. Comparison of interphase boundary structure between bainite and martensite in steel10.1016/S1359-6462(02)00128-8 ↗
71. The role of crystal misorientations during solid-state nucleation of ferrite in austenite10.1016/j.actamat.2008.11.034 ↗
72. Orientation relationship between austenite and bainite in a multiphased steel10.1016/j.matchar.2006.05.016 ↗
73. Ultra-high-strength bainitic steels10.2355/isijinternational.45.1736 ↗
74. Tetragonal martensites in ferrous alloys - a critique10.2320/matertrans1989.33.208 ↗
75. Anisotropy in fracture and fatigue resistance of pearlitic steels and its effect on the crack path10.1016/j.ijfatigue.2019.02.048 ↗
76. Depth-sensing indentation-based studies of surface mechanical behavior and fatigue damage evolution of an austenitic stainless steel subjected to cyclic straining10.1016/j.msea.2015.10.024 ↗