Abnormal influence of impurity element phosphorus on the hot ductility of SA508Gr.4N reactor pressure vessel steel
Source abstract
Abstract
Abstract The effect of phosphorous on the hot-ductility of SA508Gr.4N reactor pressure vessel (RPV) steel has been studied. The investigation is done with the use of a Gleeble machine in conjunction with optical metallography, scanning electron microscopy, and transmission electron microscopy. It is observed that both the undoped and P-doped steels exhibit hot-ductility troughs between 750 and 900 °C. However, the trough for the P-doped steel is much shallower than that for the undoped steel. At around 850 °C, the reduction of area (RA) of the undoped steel is quite low (~50%), in comparison to the P-doped steel (~75%). Since there is no grain-boundary precipitation of ferrite and carbides in both undoped and P-doped samples over this temperature range, it can be inferred that the enhancement in hot-ductility for the P-doped steel is independent of these two factors. Grain-boundary microanalysis shows the presence of grain-boundary segregation of P in the tested P-doped samples, implying that the P-induced hot-ductility improvement of this RPV steel may arise from the suppression of grain-boundary sliding by P grain-boundary segregation. Undoubtedly, the present effect of P is unusual and the underlying mechanism for this effect has been briefly discussed. It needs to be underlined that a minor addition of P can play a positive role in the hot-ductility improvement of SA508Gr.4N RPV steel.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Fusion materials and technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Structural integrity of nuclear reactor pressure vessels10.1080/14786435.2013.815379 ↗
2. Materials challenges in nuclear energy10.1016/j.actamat.2012.11.004 ↗
3. Comparison of fracture properties in SA508 Gr.3 and Gr.4N high strength low alloy steels for advanced pressure vessel materials10.1016/j.ijpvp.2015.04.010 ↗
4. Characterization of transition behavior in SA508 Gr.4N Ni–Cr–Mo low alloy steels with microstructural alteration by Ni and Cr contents10.1016/j.msea.2011.09.012 ↗
5. Cleavage fracture toughness of tempered martensitic Ni–Cr–Mo low alloy steel with different martensite fraction10.1016/j.msea.2011.11.043 ↗
6. Influence of the thermodynamic parameters on the temper embrittlement of SA508 Gr.4N Ni–Cr–Mo low alloy steel with variation of Ni, Cr and Mn contents10.1016/j.jnucmat.2012.02.032 ↗
7. Modeling flow stress constitutive behavior of SA508-3 steel for nuclear reactor pressure vessels10.1016/j.jnucmat.2011.07.011 ↗
8. Hot deformation behavior and microstructural evolution of SA508-ⅠV steel10.1002/srin.201800208 ↗
9. Effect of minor rare earth cerium addition on the hot ductility of a reactor pressure vessel steel10.1016/j.rinp.2019.102746 ↗
10. Mathematical model of the thermal processing of steel ingots: Part II. Stress model10.1007/BF02658438 ↗
11. Hot ductility of steels and its relationship to the problem of transverse cracking during continuous casting10.1179/imr.1991.36.1.187 ↗
12. Influence of sulphur and niobium on hot ductility of as cast steels10.1179/mst.1991.7.12.1101 ↗
13. The influence of composition on the hot ductility of steels and to the problem of transverse cracking10.2355/isijinternational.39.833 ↗
14. Effects of phosphorus and sulfur on the thermoplasticity of high manganese austenitic steel10.1016/j.msea.2010.05.023 ↗
15. Influence of phosphorus on the hot ductility of 2.25Cr1Mo steel10.1179/026708303225007933 ↗
16. Influence of P and N on hot ductility of high Al, boron containing TWIP steels10.1179/1743284714Y.0000000576 ↗
17. Influence of sulphur and phosphorus on the hot deformation of Fe-Cr 13% high purity steel10.1051/jp4:1995741 ↗
18. Precipitation of NbC and hot ductility of austenitic stainless steel10.2320/jinstmet1952.48.2_158 ↗
19. Hot-ductility behaviour of C–Mn–Nb–Al steels and its relationship to crack propagation during the straightening of continuously cast strand10.1179/030716979803276471 ↗
20. The precipitation of AlN and NbC and the hot ductility of low carbon steels10.1016/0025-5416(84)90272-6 ↗
21. Influence of P on hot ductility of high C, Al, and Nb containing steels10.1179/026708303225009409 ↗
22. Critical hot plasticity and transverse cracking in continuous slab casting with particular reference to composition10.2355/isijinternational1966.25.149 ↗
23. Phosphorus-induced hot ductility enhancement of 1Cr-0.5Mo low alloy steel10.1016/j.msea.2013.02.072 ↗
24. Influence of Al and P additions on hot ductility of steels10.1179/174328407X179737 ↗
25. Studies of the conditions of formation of transverse corner cracks on the surface of continuous-cast slabs10.1007/s11015-012-9492-0 ↗
26. An FEGSTEM study of grain boundary segregation of phosphorus during quenching in a 2.25Cr-1Mo steel
27. Solute grain boundary segregation during high temperature plastic deformation in a Cr–Mo low alloy steel10.1016/j.msea.2011.06.084 ↗
28. Effectiveness of hot tensile test in simulating straightening in continuous-casting10.1179/mst.1992.8.2.171 ↗
29. Chen · 2015
30. Austenite transformation of SA508Gr.4N steel for nuclear reactor pressure vessels during heating process
31. Improvement of hot ductility of C-Mn steel containing arsenic by rare earth Ce10.1051/metal/2018030 ↗
32. Effects of B on the hot ductility of Fe-36Ni invar alloy10.1515/htmp-2018-0076 ↗
33. Effect of strain rate, soaking time and alloying elements on hot ductility and hot shortness of low alloy steels10.1016/j.msea.2018.01.084 ↗
34. Effects of Ti-Ce refiners on solidification structure and hot ductility of Fe-36Ni invar alloy10.1016/S1002-0721(12)60381-0 ↗
35. Effect of yttrium on hot tensile properties of austenitic heat-resistant steel and corresponding mechanism
36. Influence of cerium on hot workability of 00Cr25Ni7Mo4N super duplex stainless steel10.1016/S1002-0721(09)60100-9 ↗
37. Influence of deformation induced ferrite, grain boundary sliding, and dynamic recrystallisation on hot ductility of 0.1-0.75% C steels10.1179/mst.1993.9.10.907 ↗
38. Deformation induced ferrite and its influence on the elevated temperature tensile flow stress–elongation curves of plain C–Mn and Nb containing steels10.1179/174328406X91177 ↗
39. Effect of rare-earth cerium on impurity tin-induced hot ductility deterioration of SA508-III reactor pressure vessel steel10.1002/srin.201500425 ↗
40. Recent advances in hot working: fundamental dynamic softening mechanisms10.1007/BF02833651 ↗
41. Tin-induced hot ductility degradation and its suppression by phosphorus for a Cr–Mo low-alloy steel10.1016/j.msea.2013.12.010 ↗
42. Hot ductility curve of an austenitic stainless steel and importance of dynamic recrystallisation in determining ductility recovery at high temperatures10.1179/026708399101505086 ↗
43. Adsorption-induced interface decohesion10.1016/0001-6160(80)90112-1 ↗
44. Embrittlement of interfaces by solute segregation10.1016/0921-5093(89)90372-9 ↗
45. Segregation-induced changes in grain boundary cohesion and embrittlement in binary alloys10.1016/j.actamat.2015.05.004 ↗
46. Interfacial segregation and grain boundary embrittlement: an overview and critical assessment of experimental data and calculated results10.1016/j.pmatsci.2016.11.001 ↗
47. M · 1957
48. L · 2010
49. Mechanisms of temper embrittlement and recovery in cast HY-80 high-strength low-alloy steel10.1007/s10853-018-2973-1 ↗
50. Low temper embrittlement and brittle-to-ductile transition in 0.2 mass% carbon steels10.2355/tetsutohagane.TETSU-2015-113 ↗
51. Temper embrittlement in a Ni-Cr steel containing phosphorus as impurity10.1007/BF02662740 ↗
52. Nonequilibrium grain boundary segregation in austenitic alloys10.1007/BF00738626 ↗
53. Effect of boron on phosphorus-induced temper embrittlement10.1023/A:1004776931616 ↗
54. Kinetics of non-equilibrium grain-boundary segregation10.1016/S0079-6425(03)00019-7 ↗
55. Grain boundary cavitation and sliding in copper/tungsten composites due to thermal stresses10.1080/14786437308217462 ↗
56. Cavity growth and grain boundary sliding in polycrystalline solids10.1016/0167-6636(86)90037-2 ↗
57. Ashby · 2012
58. Influence of Cu and Sn on hot ductility of steels with various C content10.2355/isijinternational.37.255 ↗
59. The role of tin in the hot-ductility deterioration of a low-carbon steel10.1007/s11661-003-0306-7 ↗
60. Effect of rare earth cerium and impurity tin on the hot ductility of a Cr-Mo low alloy steel10.1016/S1002-0721(16)60135-7 ↗