The influence of heating rate on the microstructural evolutions and mechanical properties of spark plasma sintered multi-walled carbon nanotubes reinforced NiAl intermetallic matrix composites
Source abstract
Abstract
Abstract The effect of heating rate on the mechanical characteristics and microstructures of multi-walled carbon nanotubes (MWCNTs) reinforced nickel aluminide (NiAl) was studied. Powder synthesis was carried out by the use of the planetary ball milling and the admixed powders were fabricated by spark plasma sintering (SPS) technique to promote homogeneity. Three values of the heating rate was used namely 50, 100 and 150 °C/min to evaluate the effect of heating rate on the resulting microstructures and mechanical properties of the sintered composites. The microstructures of the sintered composites revealed the presence of porosity as the heating rate was higher, due to lack of contact area between particles. The densifications of the composites were observed to decrease as the heating rate was increased. Furthermore, results showed that a heating rate of 50 °C/min gave the best combination of properties among the composite batches with nanohardness of 9.6 GPa, microhardness of 371.2 HV, elastic modulus of 107.7 GPa, and relative density of 95.7%.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced ceramic materials synthesis · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Predicting Charpy impact energy of Al6061/SiCp laminated nanocomposites in crack divider and crack arrester forms10.1016/j.ceramint.2013.01.027 ↗
2. Toughness behavior in roll-bonded laminates based on AA6061/SiCp composites10.1016/j.msea.2014.01.014 ↗
3. Al-Mg-Si/SiC laminated composites: fabrication, architectural characteristics, toughness, damage tolerance, fracture mechanisms10.1016/j.compositesb.2017.05.055 ↗
4. Advanced materials for automotive applications: an overview
5. Toughness enhancement in architecturally modified Al6061-5 vol.% SiCp laminated composites10.1177/1056789514529984 ↗
6. Carbon nanotube reinforced metal matrix composites - a review10.1179/095066009X12572530170543 ↗
7. Helical microtubules of graphitic carbon10.1038/354056a0 ↗
8. Optical investigation of reduced graphene oxide and reduced graphene oxide/CNTs grown via simple CVD method10.1016/j.synthmet.2016.05.013 ↗
9. Synthesis of self-assembled and hierarchical palladium-CNTs-reduced graphene oxide composites for enhanced field emission properties10.1016/j.matdes.2017.02.089 ↗
10. Effect of carbon nanotube (CNT) content on the mechanical properties of CNT-reinforced aluminium composites10.1016/j.compscitech.2010.05.004 ↗
11. Improving the strengthening efficiency of carbon nanotubes in titanium metal matrix composites10.1016/j.msea.2017.04.026 ↗
12. In situ stabilized carbon nanofiber (CNF) reinforced epoxy nanocomposites10.1039/c0jm00063a ↗
13. Carbon nanotube reinforced titanium metal matrix composites prepared by powder metallurgy—a review10.1080/10408436.2014.929521 ↗
14. Spark plasma sintering of graphitized multi-walled carbon nanotube reinforced Ti6Al4V10.1016/j.matdes.2017.05.003 ↗
15. Dispersion characteristics, interfacial bonding and nanostructural evolution of MWCNT in Ti6Al4V powders prepared by shift speed ball milling technique10.1016/j.jallcom.2019.01.174 ↗
16. Effect of CNT addition approach on the microstructure and properties of NiAl-CNT nanocomposites produced by mechanical alloying and spark plasma sintering10.1016/j.intermet.2016.06.010 ↗
17. Carbon nanotube reinforced aluminum matrix composites produced by spark plasma sintering10.1007/s10853-017-1086-6 ↗
18. Dispersion analysis of carbon nanotubes, carbon onions, and nanodiamonds for their application as reinforcement phase in nickel metal matrix composites10.1039/C5RA14310A ↗
19. Load transfer and deformation mechanisms in carbon nanotube-polystyrene composites10.1063/1.126500 ↗
20. Advances in the science and technology of carbon nanotubes and their composites: a review10.1016/S0266-3538(01)00094-X ↗
21. Powder metallurgy Ti–TiC metal matrix composites prepared by in situ reactive processing of Ti-VGCFs system10.1016/j.carbon.2013.04.088 ↗
22. Role of process control agent in the synthesis of multi‐walled carbon nanotubes reinforced titanium metal matrix powder mixtures10.1002/adem.201500346 ↗
23. CNTs/Cu-Ti composites fabrication through the synergistic reinforcement of CNTs and in situ generated nano-TiC particles10.1016/j.jallcom.2018.08.116 ↗
24. Densification, hardness and tribological characteristics of MWCNTs reinforced Ti6Al4V compacts consolidated by spark plasma sintering10.1016/j.jallcom.2018.03.373 ↗
25. Interdependencies between graphitization of carbon nanotubes and strengthening mechanisms in titanium matrix composites10.1016/j.mtla.2018.08.015 ↗
26. Oxidation of NiAl and FeAl10.1016/S0966-9795(99)00037-0 ↗
27. Interface structure, chemistry and properties of NiAl composites fabricated from matrix-coated single-crystalline Al2O3 fibres (sapphire) with and without an hBN interlayer10.1016/j.actamat.2006.01.032 ↗
28. NiAl alloys for high-temperature structural applications10.1007/BF03220163 ↗
29. Sessile dislocations by reactions in NiAl severely deformed at room temperature10.1016/j.jallcom.2014.09.226 ↗
30. Microstructure and mechanical properties of spark plasma sintered nanocrystalline Ni3Al-xB (0.0< x< 1.5 at%) alloy10.1016/j.mtcomm.2018.09.002 ↗
31. Effect of mechanical alloying on the structure and property of Ni3Al fabricated by hot pressing10.1016/j.jallcom.2005.09.082 ↗
32. Fabrication and characterization of titanium-nickel-zirconia matrix composites prepared by spark plasma sintering10.1016/j.jallcom.2017.03.340 ↗
33. Formation of nanocrystalline TiC from titanium and different carbon sources by mechanical alloying10.1016/j.jallcom.2008.04.070 ↗
34. Microstructure and mechanical properties of carbon nanotubes reinforced titanium matrix composites fabricated via spark plasma sintering10.1016/j.msea.2017.02.019 ↗
35. The effects of ball milling process on the diameter dependent fracture of single walled carbon nanotubes10.1016/j.scriptamat.2007.01.023 ↗
36. Study of carbon nanotubes in Cu-Cr metal matrix composites10.1007/s11665-012-0198-z ↗
37. Effect of ball-milling time on mechanical properties of carbon nanotubes reinforced aluminum matrix composites10.1016/j.compositesa.2012.07.026 ↗
38. Physicomechanical properties of spark plasma sintered carbon nanotube-reinforced metal matrix nanocomposites10.1016/j.pmatsci.2017.07.007 ↗
39. Spark plasma sintering (SPS) method, systems and applications10.1016/B978-0-12-385469-8.00060-5 ↗
40. Mechanical alloying and milling10.1016/S0079-6425(99)00010-9 ↗
41. Effect of SPS process sintering on the microstructure and mechanical properties of nanocrystalline TiC for tools application10.1016/j.ijrmhm.2011.06.013 ↗
42. Critical review of analysis and interpretation of nanoindentation test data10.1016/j.surfcoat.2005.03.018 ↗
43. Nanoindentation of Za-27 alloy based nanocomposites reinforced with Al 2 O 3 particles
44. Evaluation of effect of grain size on mechanical and tribological properties of pulse electrodeposited nanocrystalline nickel using nanoindentation techniques10.1179/0020296712Z.00000000020 ↗
45. Electron diffraction
46. Studies on structural defects on 60Co irradiated multi walled carbon nanotubes10.1016/j.mspro.2014.07.231 ↗
47. Transmission electron microscopy characterization of different nanotubes10.1080/15533174.2015.1137317 ↗
48. Evaluating the characteristics of multiwall carbon nanotubes10.1016/j.carbon.2011.03.028 ↗
49. 3 - nickel aluminides
50. A comparison between Raman spectroscopy and surface characterizations of multiwall carbon nanotubes10.1016/j.carbon.2006.05.021 ↗
51. Solid State Communications. Raman spectroscopy of graphene and graphite: disorder, electron–phonon coupling, doping and nonadiabatic effects10.1016/j.ssc.2007.03.052 ↗
52. Semi-quantitative X-ray diffraction analysis of fly ash by the reference intensity ratio method
53. The effect of heating rate and composition on the properties of spark plasma sintered zirconium diboride based composites10.1016/j.msea.2012.01.019 ↗
54. Effect of heating rate on densification, microstructure and strength of spark plasma sintered ZrB2-based ceramics10.1016/j.scriptamat.2010.02.002 ↗
55. Effects of heating rate on the microstructure and mechanical properties of rapid vacuum sintered translucent alumina10.1016/j.ceramint.2015.05.136 ↗
56. The fabrication and characterization of spark plasma sintered nickel based binary alloy at different heating rate10.1115/1.4044267 ↗
57. Microstructure and mechanical properties of Al matrix nanocomposites reinforced by different amounts of CNT and SiCW10.1016/j.compositesb.2019.107081 ↗
58. Measurement of hardness and elastic modulus by instrumented indentation: advances in understanding and refinements to methodology10.1557/jmr.2004.19.1.3 ↗
59. Nanoindentation studies on TiN nanoceramic reinforced Ti–6Al–4V matrix composite10.1016/j.ceramint.2017.12.042 ↗
60. Nanoindentation and wear properties of Ti and Ti-TiB composite materials produced by selective laser melting10.1016/j.msea.2017.01.096 ↗
61. Direct observation of toughening mechanisms in carbon nanotube ceramic matrix composites10.1016/j.actamat.2003.10.050 ↗
62. Effect of CNTs content on the microstructures and properties of CNTs/Cu composite by microwave sintering10.1016/j.jallcom.2018.08.315 ↗