journal article·2019-11

Influence of Co addition on the deformation behavior and mechanical properties of Ni–16Cr–11Mo–2Cu alloy

Biaobiao Yang, Chenying Shi, Jianwei Teng, Qian Lei, Yan Nie, Yunping Li

Publisher page

Abstract

Abstract The roles of Co on the strain-hardening behavior, deformation mechanism, mechanical properties and facture mode of Ni–16Cr–11Mo–2Cu alloy were thoroughly investigated using tensile tests, SEM, EBSD, TEM and HRTEM. Two alloys with a similar sole FCC-γ phase constitution, near grain size only except the composition difference of 30 wt% Co were fabricated in purpose. Co addition can overcome the strength-ductility trade-off by enhancing the strain-hardening rate and capacity. The deformation behavior evolves from slip-dominated to SFs-dominated after Co addition, due to significant decrease of stacking fault energy, the critical stresses for both SFs and twinning by Co addition. In terms of facture mode, dimples-dominated ductile fracture is transformed to quasi-cleavage fracture composed of cleavage planes and dimples after Co addition. This is probably owing to the special role of SFs on intensifying stress/strain incompatibility phenomenon in polycrystalline alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · High Temperature Alloys and Creep

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. Del Cul · 2000
2. A simultaneous corrosion/irradiation facility for testing molten salt-facing materials10.1016/j.nimb.2018.11.024 ↗
3. Fluorine compounds, inorganic
4. A review and comparative study of release coatings for optimised abhesion in resin transfer moulding applications10.1016/j.ijadhadh.2005.09.003 ↗
5. Ex-situ observation on the dissolution behaviour of Ni–16Cr–15Mo and Ni–30Co–16Cr–15Mo alloys in hydrofluoric acid10.1016/j.corsci.2014.10.003 ↗
6. Corrosion resistance of Cu- and Fe-modified Ni–30Co–16Cr–15Mo alloy in aqueous hydrofluoric acid10.1016/j.corsci.2014.08.010 ↗
7. Effect of Cu on the corrosion resistance and electrochemical response of a Ni–Co–Cr–Mo alloy in acidic chloride solution10.1557/jmr.2018.271 ↗
8. Effects of Cu addition on the corrosion behavior of NiCoCrMo alloys in neutral chloride solution10.1039/C7RA05617F ↗
9. Regulating the passive film of NiCoCrMo alloy in hydrofluoric acid solution by small addition of Cu10.1016/j.corsci.2015.05.024 ↗
10. Effects of cold working on corrosion resistance of Co-modified Ni–16Cr–15Mo alloy in hydrofluoric acid solution10.1016/j.corsci.2014.09.004 ↗
11. Dynamic recrystallization in biomedical Co-29Cr-6Mo-0.16N alloy with low stacking fault energy10.1016/j.msea.2016.05.045 ↗
12. Microstructure refining of Co-29Cr-6Mo-0.16N alloy in rapid hot-forging process10.1016/j.msea.2018.05.051 ↗
13. Effects of partially substituting cobalt for nickel on the corrosion resistance of a Ni–16Cr–15Mo alloy to aqueous hydrofluoric acid10.1016/j.corsci.2013.09.004 ↗
14. Influence of Mo concentration on corrosion resistance to HF acid solution of Ni–Co–Cr–Mo alloys with and without Cu10.1016/j.corsci.2015.07.004 ↗
15. Corrosion behaviours of low Mo Ni-(Co)-Cr-Mo alloys with various contents of Co in HF acid solution10.1016/j.jallcom.2019.03.325 ↗
16. Recovery of strain-hardening rate in Ni-Si alloys10.1038/srep15532 ↗
17. Significant contribution of stacking faults to the strain hardening behavior of Cu-15%Al alloy with different grain sizes10.1038/srep16707 ↗
18. Microscopic mechanisms contributing to the synchronous improvement of strength and plasticity (SISP) for TWIP copper alloys10.1038/srep09550 ↗
19. High manganese austenitic twinning induced plasticity steels: a review of the microstructure properties relationships10.1016/j.cossms.2011.04.002 ↗
20. Strain-hardening of twinning-induced plasticity steels10.1016/j.scriptamat.2011.11.029 ↗
21. High strength Fe–Mn–(Al, Si) TRIP/TWIP steels development — properties — application10.1016/S0749-6419(00)00015-2 ↗
22. Structure–properties relationship in TRIP steels containing carbide-free bainite10.1016/j.cossms.2004.10.002 ↗
23. Hertzberg · 2012
24. Influence of Co content on stacking fault energy in Ni–Co base disk superalloys10.1557/jmr.2011.346 ↗
25. The synchronous improvement of strength and plasticity (SISP) in new Ni-Co based disc superalloys by controling stacking fault energy10.1038/s41598-017-07884-4 ↗
26. A general mechanism of martensitic nucleation: Part I. General concepts and the FCC → HCP transformation
27. A general mechanism of martensitic nucleation: Part II. FCC → BCC and other martensitic transformations
28. The calculation of stacking fault energies in Fe-Ni-Cr alloys10.1016/0364-5916(78)90010-X ↗
29. Strength prediction in NiCo alloys – the role of composition and nanotwins10.1016/j.ijplas.2015.07.002 ↗
30. Laughlin · 2014
31. The influence of stacking fault energy on the microstructural and strain-hardening evolution of Fe–Mn–Al–Si steels during tensile deformation10.1016/j.actamat.2015.08.030 ↗
32. Novel Co-rich high entropy alloys with superior tensile properties10.1080/21663831.2018.1553803 ↗
33. On the stress dependence of partial dislocation separation and deformation microstructure in austenitic stainless steels10.1016/S1359-6454(03)00117-4 ↗
34. Dislocation–dislocation and dislocation–twin reactions in nanocrystalline Al by molecular dynamics simulation10.1016/S1359-6454(03)00232-5 ↗
35. Interaction between a screw dislocation and stacking faults in FCC metals10.1016/j.msea.2012.01.115 ↗
36. Mechanical response of low stacking fault energy Co–Ni alloys – continuum, mesoscopic and atomic level treatments10.1016/j.ijplas.2015.04.003 ↗
37. Grain orientation dependence of deformation twinning in pure Cu subjected to dynamic plastic deformation10.1016/j.scriptamat.2009.04.006 ↗