journal article·2019-08

Role of stress state on dynamic recrystallization behaviour of Ni during hot deformation: Analysis of uniaxial compression and plane strain compression

C.N. Athreya, S. Suwas, V. Subramanya Sarma

Publisher page

Abstract

Abstract In the present work, the role of deformation stress state (uniaxial compression (UC) and plane strain compression (PSC)) on work hardening, softening and dynamic recrystallization (DRX) behaviour of Ni during hot deformation is investigated. Hot deformation was performed through UC and PSC to a von Mises equivalent true strain of 0.7 at 973 K, 1023 K and 1073 K at strain rates of 0.01 s−1, 0.1 s−1 and 1 s−1 in a thermomechanical simulator. Analysis of flow curves revealed rapid work hardening followed by softening in PSC samples. In UC samples, continuous work hardening at a slower rate was observed and at 1123 K, steady state was achieved. Analysis of the work hardening parameter ‘h’ and dynamic recovery parameter ‘r’ from the flow curve data showed that the h and r values of PSC deformed samples are higher than UC deformed samples. The DRX behaviour is dependent on temperature and strain rate and significant difference in DRX fraction was observed between UC and PSC samples deformed at strain rate of 0.1 s−1. Evaluation of microstructure from electron back scatter diffraction maps showed that DRX fraction is significantly higher in PSC deformed samples. Samples deformed through PSC have higher annealing twin density and number of twins per grain. It is reasoned that annealing twin formation is activated by the presence of shear stress component during PSC mode of deformation. Annealing twin formation and growth in turn facilitate DRX and explain the observed differences between UC and PSC modes of deformation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallurgy and Material Forming · Microstructure and mechanical properties · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Grain-size effects during dynamic recrystallization of nickel10.1179/msc.1974.8.1.325 ↗
2. Effect of initial grain size on dynamic recrystallization in high purity austenitic stainless steels10.1016/j.actamat.2005.06.020 ↗
3. Influence of grain size on hot working stresses and microstructures in Mg–3Al–1Zn10.1016/j.scriptamat.2004.03.023 ↗
4. Microstructural development during hot working of Mg-3Al-1Zn10.1007/s11661-007-9207-5 ↗
5. Recovery and recrystallization of carbon steel between intervals of hot working10.1179/000844375795050201 ↗
6. Flow behavior and microstructures of superalloy 718 during high temperature deformation10.1016/j.msea.2008.07.046 ↗
7. Deformation stress state effects on the recrystallization kinetics of molybdenum10.1007/BF02913888 ↗
8. Influence of the mode of deformation on recrystallisation kinetics in Nickel through experiments, theory and phase field model10.1080/14786435.2017.1370146 ↗
9. Influence of the mode of deformation on recrystallisation behaviour of titanium through experiments, mean field theory and phase field model10.1088/1361-651X/aaa6a4 ↗
10. Recrystallisation following non-proportional straining in aluminium10.1179/mst.1995.11.11.1104 ↗
11. Effect of strain path change on recrystallisation in copper10.1179/174328405X43171 ↗
12. Uniaxial and plane strain compression behaviour of magnesium alloy AZ31: a comparative study10.4028/www.scientific.net/MSF.550.229 ↗
13. Influence of deformation conditions and texture on the high temperature flow stress of magnesium AZ3110.1016/S1471-5317(01)00010-4 ↗
14. Generating misorientations in shear deformation structures10.2320/matertrans.45.2151 ↗
15. Influence of state of stress on dynamic recrystallization in a titanium-modified austenitic stainless steel10.1007/s11661-011-1015-2 ↗
16. Dieter · 1988
17. A review of strain analysis using electron backscatter diffraction10.1017/S1431927611000055 ↗
18. Cube texture in hot-rolled aluminum alloy 1050 (AA1050)—nucleation and growth behavior10.1016/j.actamat.2008.02.037 ↗
19. High temperature deformation behavior of Zr-1Nb alloy10.1016/j.jallcom.2017.01.356 ↗
20. Effect of strain rate on the dynamic recrystallization behavior in a nitrogen-enhanced 316L(N)10.1007/s11661-014-2480-1 ↗
21. A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization10.1016/1359-6454(95)00146-7 ↗
22. The relation between macroscopic and microscopic strain hardening in F.C.C. polycrystals10.1016/0001-6160(84)90222-0 ↗
23. Some physical characteristics of strain hardening in severe plastic deformation10.1002/adem.201500097 ↗
24. Influence of mode of plastic straining on the microstructure of Ni and Ti deformed through rolling and torsion10.1016/j.matchar.2017.08.018 ↗
25. Dislocation structure and work hardening in polycrystalline ofhc copper rods deformed by torsion and tension10.1016/0001-6160(86)90012-X ↗
26. Hot deformation and dynamic restoration
27. Dynamic recrystallization behavior of a typical nickel-based superalloy during hot deformation10.1016/j.matdes.2013.12.072 ↗
28. EBSD study of a hot deformed nickel-based superalloy10.1016/j.jallcom.2015.04.008 ↗
29. A unified phenomenological description of work hardening and creep based on one-parameter models10.1016/0001-6160(84)90202-5 ↗
30. The Avrami kinetics of dynamic recrystallization10.1016/j.actamat.2009.02.033 ↗
31. Prediction of steel flow stresses at high temperatures and strain rates10.1007/BF02667368 ↗
32. Frost · 1982
33. Hot deformation and recrystallization mechanisms in a coarse-grained, niobium stabilized austenitic stainless steel (316Nb)10.1007/s11661-018-05103-x ↗
34. Hot deformation behavior and constitutive modeling of VCN200 low alloy steel10.1016/j.apm.2012.01.008 ↗
35. A novel approach to find the kinetics of dynamic recovery based on hot flow curves10.1016/j.msea.2012.02.093 ↗
36. A method of measuring stored energy macroscopically using statistically stored dislocations in commercial purity aluminum10.1007/s11661-006-0148-1 ↗
37. Stored Energy and Taylor Factor Relation in an Al-Mg-Mn Alloy Sheet Worked by Continuous Cyclic Bending10.2320/matertrans.45.2316 ↗
38. Effect of deformation mode and grain orientation on misorientation development in a body-centered cubic steel10.1016/j.actamat.2007.05.014 ↗
39. Influence of mode of deformation on microstructural heterogeneities in Ni subjected to large strain deformation10.1080/09500839.2015.1085129 ↗
40. Urai · 1986
41. Prediction of the critical conditions for dynamic recrystallization in the austenitic steel 800H10.1016/j.msea.2004.02.098 ↗
42. Thermo-mechanical factors influencing annealing twin development in nickel during recrystallization10.1007/s10853-015-9067-0 ↗
43. The role of shear stress in the formation of annealing twin boundaries in copper10.1016/j.scriptamat.2005.11.037 ↗
44. Microstructural evolution in nickel during rolling and torsion10.1179/mst.1991.7.6.544 ↗
45. Study of annealing twins in fcc metals and alloys10.1007/BF02647209 ↗
46. The mobility and migration of boundaries