journal article·2018-01

Positive effect of hydrogen on interface of in situ synthesized Ti-6Al-4V matrix composites

Xuan Wang, Liang Wang, LiangShun Luo, XiaoDong Liu, YingChun Tang, Hui Yan, LongHui Yao, YanQing Su, JingJie Guo, HengZhi Fu

Publisher page

Abstract

Abstract This paper presented another methodology, melt hydrogenation (melting alloys in gas mixture of argon and hydrogen), to produce in situ synthesized Ti-6Al-4V matrix composites (TMCs) with quality interface after hot deformation. Microstructure results of as cast TMCs indicated hydrogen didn’t obviously change morphology of interface, but induced more TiBw whiskers with higher length-diameter ratio, which was attributed to hydrogen improving growth rate of TiBw whiskers by accelerating atomic diffusion. After hot compression, experimental results indicated proper content of hydrogen addition decreased the flowing stress of both matrix and TMCs, and eliminated most cracks and holes along the interface, quality interface without defects was attributed to improvement on flowing ability of matrix alloy. The positive effect of hydrogen on interface was explained by hydrogen induced softening on matrix alloy. Electron back-scatter diffraction (EBSD) images indicated hydrogen increased softer β phase content which was favor to fill up the defects caused by crush of ceramic particles. And hydrogen promoted discontinuous dynamic recrystallization (DRX) by accelerating migration of grain boundaries which ended up at the interface, and then eliminated defects caused by disharmonious motion between ceramic particles and matrix.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Metal and Thin Film Mechanics · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Microstructurally inhomogeneous composites: is a homogeneous reinforcement distribution optimal?10.1016/j.pmatsci.2015.01.002 ↗
2. In situ (TiBw + TiCp)/Ti6Al4V composites with a network reinforcement distribution10.1016/j.msea.2010.07.025 ↗
3. Comparative study on superplastic tensile behaviors of the as-extruded Ti6Al4V alloys and TiBw/Ti6Al4V composites with tailored architecture10.1016/j.matdes.2015.12.162 ↗
4. TiB whiskers reinforced high temperature titanium Ti60 alloy composites with novel network microstructure10.1016/j.matdes.2013.04.048 ↗
5. Effects of heat treatment parameters on the microstructure and mechanical properties of in situ TiBw/Ti6Al4V composite with a network architecture10.1016/j.matdes.2011.12.021 ↗
6. Positive effects of hydrogen in metals10.1016/S0921-5093(99)00670-X ↗
7. Effect of temperature and hydrogen concentration on the lattice parameter of beta titanium10.1016/S0025-5408(01)00604-3 ↗
8. Kinetics of martensite decomposition in Ti-6Al-4V-xH alloys10.1016/S0921-5093(03)00350-2 ↗
9. Temperature dependence of tensile properties and fracture behavior of as rolled TiB/Ti composite sheet10.1016/j.msea.2012.07.110 ↗
10. Evolution of microstructure and tensile properties of in situ titanium matrix composites with volume fraction of (TiB plus TiC) reinforcements10.1016/j.msea.2012.04.004 ↗
11. Evolution of microstructural characteristic and tensile properties during preparation of TiB/Ti composite sheet10.1016/j.matdes.2011.11.060 ↗
12. Effect of hydrogen on mold filling behavior of TiAl alloy10.1016/j.intermet.2014.07.008 ↗
13. Effect of hydrogen on superplastic deformation of (TiB + TiC)/Ti-6Al-4V composite10.1016/j.ijhydene.2009.07.091 ↗
14. Hot deformation behavior and microstructure evaluation of hydrogenated Ti-6Al-4V matrix composite10.1016/j.ijhydene.2009.09.029 ↗
15. Effect of hydrogen on microstructure and high temperature deformation of (TiB + tic)/Ti-6Al-4V composite10.1016/j.msea.2008.09.047 ↗
16. Superplasticity of coarse-grained (TiB+TiC)/Ti–6Al–4V composite10.1016/j.jallcom.2009.10.009 ↗
17. Hot deformation behavior and dynamic recrystallization of melt hydrogenated Ti-6Al-4V alloy10.1016/j.jallcom.2017.09.044 ↗
18. High temperature deformation behavior of melt hydrogenated (TiB+tic)/Ti-6Al-4V composites10.1016/j.matdes.2017.02.075 ↗
19. Hydrogen induced softening and hardening for hot workability of (TiB + TiC)/Ti-6Al-4V composites10.1016/j.ijhydene.2017.01.030 ↗
20. Brief review of removal effect of hydrogen-plasma arc melting on refining of pure titanium and titanium alloys10.1016/j.ijhydene.2016.09.082 ↗
21. First-principles study of hydrogen diffusion in alpha Ti10.1016/j.ijhydene.2009.02.061 ↗
22. First-principles study of the effect of hydrogen on the Ti self-diffusion characteristics in the alpha Ti-H system10.1016/j.scriptamat.2006.06.037 ↗
23. First principles determination of elastic constants and chemical bonding of titanium boride (TiB) on the basis of density functional theory10.1016/j.actamat.2005.12.003 ↗
24. Mechanical properties of Ti-6Al-4V/TiB composites with randomly oriented and aligned TiB reinforcements10.1016/S1359-6454(02)00510-4 ↗
25. The evolution of microstructure in a laser clad TiB-Ti composite coating10.1016/S1359-6454(02)00475-5 ↗
26. Effect of hydrogen on the elastic modulus and hardness of gamma titanium aluminides10.1016/S1359-6462(99)00197-9 ↗
27. Effect of 0.3 wt%H addition on the high temperature deformation behaviors of Ti-6Al-4V alloy10.1016/j.ijhydene.2007.04.032 ↗
28. Spheroidization of the lamellar microstructure in Ti–6Al–4V alloy during warm deformation and annealing10.1016/j.actamat.2011.03.037 ↗
29. Hot deformation behavior of Ti-6Al-4V alloy: effect of initial microstructure10.1016/j.jallcom.2017.05.097 ↗
30. Dynamic globularization and restoration mechanism of Ti–5Al–2Sn–2Zr–4Mo–4Cr alloy during isothermal compression10.1016/j.jallcom.2014.10.043 ↗
31. Hardening effects in plastically deformed Pd with the addition of H10.1016/j.scriptamat.2014.11.012 ↗