journal article·2016-08

The effect of warm deforming and reversal austenization on the microstructure and mechanical properties of a microalloyed steel

X.J. Shen, S. Tang, J. Chen, Z.Y. Liu, R.D.K. Misra, G.D. Wang

Publisher page

Abstract

Abstract The influence of warm deforming and reversal austenization on the microstructure and mechanical properties of a microalloyed steel was elucidated. Grain refinement induced by warm deforming and reversal austenization was studied by thermal simulation experiments, and its effect on properties was assessed by thin-plate hot rolling experiments. The study suggested that austenite was refined to ~10 µm after reversal austenization, which was further refined to ~5 µm after reversal austenization and application of warm deforming. Warm deforming recrystallized the microstructure during the reheating process, when the reheating rate was less than 2 °C/s. While recrystallization was inhibited at reheating rates greater than 5 °C/s. The ultimate microstructure obtained from the refined austenite via combination of warm deforming and reversal austenization, comprised of fine-grained (4.7±3.2 µm) ferrite and pearlite with small colony size (1.3±0.6 µm). On the other hand, the fine-grained microstructure was characterized by reduced extent of coarse precipitation (9.3±3.4 nm), compared to the coarse-grained thermo-mechanical controlled processing (TMCP) plate with dispersed and fine precipitation (4.0±1.3 nm), which was responsible for lower strength (~70 MPa) of the fine-grained plate than the coarse-grained TMCP plate. However, the fine-grained plate had an excellent low temperature toughness resulting from fine grain size, coarse precipitation, and small pearlite colony size.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. T. Ishikawa, H. Yoshikawa, T. Inoue, Y. Nomiyama, S. Imai, Ultra-high Crack-arresting Steel Plate (HIAREST) with Super-refined Grains in Surface Layers, Nippon Steel Tech. Report 75, 1997, pp. 31–42.
2. Metallurgical features of steel plates with ultra fine grains in surface layers and their formation mechanism10.2355/isijinternational.39.477 ↗
3. T. Ishikawa, H. Yoshikawa, T. Inoue, S. Imai, Improvement in Safety of Ships by Use of Steel with High Crack Arrestability (HIAREST), Nippon Steel Tech. Report 81, 2000, pp. 109–113.
4. Formation of ultrafine grained ferrite by warm deforming of lath martensite in low-alloy steels with different carbon content10.1016/j.scriptamat.2008.03.041 ↗
5. Formation process and mechanical properties of 0.2% carbon steel with bimodal microstructures subjected to heavy-reduction single-pass hot/warm compression10.1016/j.msea.2012.12.061 ↗
6. Formation of ultrafine grained ferrite in low carbon steel by heavy deformation in ferrite or dual phase region
7. Phase transformation from fine-grained austenite10.2355/isijinternational.48.1038 ↗
8. Ultrafine grained austenite in a low carbon vanadium microalloyed steel10.1016/S1006-706X(13)60084-9 ↗
9. Recrystallization and Formation of austenite in deformed lath martensitic structure of low carbon steels10.1007/BF02642875 ↗
10. Determination of Ms temperature in steels: a bayesian neural network model10.2355/isijinternational.42.894 ↗
11. Modelling of CCT diagrams for engineering and constructional steels10.1016/j.jmatprotec.2007.04.099 ↗
12. Difference in recrystallization behavior between lath martensite and deformed ferrite in ultralow carbon steel10.1016/j.scriptamat.2005.04.025 ↗
13. Effect of composition and austenite deformation on the transformation characteristics of low-carbon and ultralow-carbon microalloyed steels10.1007/s11661-002-0059-8 ↗
14. Microstructural features controlling mechanical properties in Nb–Mo microalloyed steels. part I: yield strength10.1007/s11661-014-2450-7 ↗
15. Precipitation hardening in metal10.1179/026708399773002782 ↗
16. Dispersion hardening by niobiun carbonitride precipitation in ferrite10.1179/mst.1997.13.9.731 ↗
17. Microstructural evolution and mechanical properties of high strength microalloyed steels: ultra fast cooling (UFC) versus accelerated cooling (ACC)10.1016/j.msea.2013.05.016 ↗
18. Improvement of yield strength-transition temperature balance by microstructural refinement10.2355/isijinternational.36.341 ↗
19. Microstructural features controlling mechanical properties in Nb–Mo microalloyed steels. part II: impact toughness10.1007/s11661-014-2451-6 ↗
20. Precipitation and impact toughness of Nb–V stabilised 18Cr–2Mo ferritic stainless steel during isothermal aging10.1016/j.msea.2014.06.029 ↗