journal article·2020-06Open access

Revealing the local fatigue behavior of bimodal copper laminates by micropillar fatigue tests

Sebastian Krauß, Thomas Schieß, Mathias Göken, Benoit Merle

Abstract

Abstract Cyclic micropillar compression is a powerful technique for characterizing the local fatigue properties of microstructurally complex materials. Here, it was applied to a bimodal copper sample made of alternating ultrafine and coarse grained layers. Micropillars were fabricated from both domains, as well as from the interface between them. The three different areas were investigated from the quasi-static to the high cycle fatigue range (up to 1 million cycles). In line with expectations, the CG micropillars exhibit the smallest fatigue strength and the UFG specimens the highest one. More surprisingly, the micropillars containing a bimodal UFG/CG interface exhibit a slightly shorter fatigue lifetime than plain UFG specimens. The likely reason is their more complex stress state, which alternates between tension and compression and results in the formation of surface extrusions, which lead to eventual failure.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Microstructure and mechanical properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Bimodal grain size distributions in UFG materials produced by SPD – their evolution and effect on the fatigue and monotonic strength properties
2. Enhanced tensile ductility and strength of electrodeposited ultrafine-grained nickel with a desired bimodal microstructure10.1016/j.msea.2017.06.063 ↗
3. Experiment and FEM analysis of tensile behavior of bimodal nanocrystalline Al-Mg alloys10.1557/PROC-821-P9.11 ↗
4. Effect of bimodal microstructure on the tensile properties of selective laser melt Al-Mg-Sc-Zr alloy10.1016/j.jallcom.2019.152422 ↗
5. Crack propagation and mechanical properties of electrodeposited nickel with bimodal microstructures in the nanocrystalline and ultrafine grained regime10.1557/jmr.2017.353 ↗
6. Annealing treatments to enhance thermal and mechanical stability of ultrafine-grained metals produced by severe plastic deformation
7. Bimodal grain size distributions in UFG materials produced by SPD: their evolution and effect on mechanical properties10.1088/1742-6596/240/1/012147 ↗
8. Cyclic deformation and fatigue properties of very fine-grained metals and alloys10.1016/j.ijfatigue.2009.10.007 ↗
9. On the possabilities to enhance the fatigue properties of ultrafine-grained metals: dedicated to Professor Dr. Haël Mughrabi on the occasion of his 65th birthday
10. Impact of partial recrystallization on the mechanical properties of severely deformed copper10.1016/j.msea.2015.11.003 ↗
11. A bimodal bulk ultra-fine-grained nickel: experimental and micromechanical investigations10.1016/j.mechmat.2010.02.001 ↗
12. Tailoring bimodal grain size structures in nanocrystalline compositionally complex alloys to improve ductility10.1016/j.msea.2019.01.073 ↗
13. How to produce a desired bimodal microstructure for optimized mechanical properties: Investigation of the mechanisms of abnormal grain growth in pulsed electro-deposited nickel10.3139/146.111291 ↗
14. Global and local strain rate sensitivity of bimodal Al-laminates produced by accumulative roll bonding10.1016/j.actamat.2015.11.009 ↗
15. Evolution of microstructure and texture during deformation and recrystallization of heavily rolled Cu-Cu multilayer10.1007/s11661-013-1749-0 ↗
16. High-strength and ductility bimodal-grained Al–Li/Al–Li–Zr composite produced by accumulative roll bonding10.1016/j.msea.2019.138049 ↗
17. Texture and mechanical properties of Al–Mg alloy with unimodal and bimodal grain-structures formed by accumulative roll bonding and annealing10.2320/matertrans.L-M2018820 ↗
18. Sample dimensions influence strength and crystal plasticity10.1126/science.1098993 ↗
19. Influence of stacking fault energy and dislocation character on slip transfer at coherent twin boundaries studied by micropillar compression10.1016/j.actamat.2018.05.037 ↗
20. Differences in deformation behavior of bicrystalline Cu micropillars containing a twin boundary or a large-angle grain boundary10.1016/j.actamat.2014.04.022 ↗
21. Cyclic response of copper single crystal micro-beams10.1016/j.scriptamat.2010.05.014 ↗
22. Stress-controlled fatigue behaviour of micro-sized polycrystalline copper wires10.1016/j.msea.2009.02.037 ↗
23. On the reversibility of dislocation slip during small scale low cycle fatigue10.1016/j.actamat.2015.04.029 ↗
24. Acquiring in situ fatigue crack growth curves by a compliance method for micro bending beams to reveal the interaction of fatigue cracks with grain boundaries10.1016/j.prostr.2019.08.003 ↗
25. Microscale high-cycle fatigue testing by dynamic micropillar compression using continuous stiffness measurement10.1007/s11340-017-0362-3 ↗
26. Influence of modulus-to-hardness ratio and harmonic parameters on continuous stiffness measurement during nanoindentation10.1016/j.actamat.2017.05.036 ↗
27. Critical issues in conducting constant strain rate nanoindentation tests at higher strain rates10.1557/jmr.2019.292 ↗
28. Influence of solid solution strengthening on the local mechanical properties of single crystal and ultrafine-grained binary Cu–Al X solid solutions10.1557/jmr.2017.320 ↗
29. Dynamic nanoindentation testing for studying thermally activated processes from single to nanocrystalline metals10.1016/j.cossms.2015.02.001 ↗
30. The correlation between the internal material length scale and the microstructure in nanoindentation experiments and simulations using the conventional mechanism-based strain gradient plasticity theory10.1557/jmr.2009.0123 ↗
31. Additional grain boundary strengthening in length-scale architectured copper with ultrafine and coarse domains10.1016/j.scriptamat.2019.02.019 ↗
32. The effect of grain size on fatigue10.1016/0001-6160(71)90012-5 ↗
33. The influence of microstructure on the cyclic deformation and damage of copper and an oxide dispersion strengthened steel studied via in-situ micro-beam bending10.1016/j.msea.2017.01.073 ↗
34. Advanced characterisation of thermo-mechanical fatigue mechanisms of different copper film systems for wafer metallizations10.1016/j.tsf.2016.05.044 ↗
35. Bauschinger effect in thin metal films10.1016/j.scriptamat.2005.03.048 ↗
36. Bulge fatigue testing of freestanding and supported gold films10.1557/jmr.2013.373 ↗