journal article·2020-01

Preparation of in situ NbC–TiC@Graphene/Fe composite inoculant and its effect on microstructures and properties of GCr15

Yaqi Zhao, Chunxiang Cui, Xuhao Han, Sen Cui, Ning Li, Zhu Qian

Publisher page

Abstract

Abstract The NbC–TiC@Graphene/Fe composite inoculant was prepared by in situ reaction and high-energy ball milling techniques. The ceramic nanoparticles in the inoculant are surrounded by graphene and amorphous components. Compared with GCr15 without inoculation, the microstructure and mechanical properties of GCr15 bearing steel after inoculation treatment and heat treatment were studied. The inoculation treatment increases the nucleation rate of the as-cast microstructure, and the pearlite interlayer spacing and grain size are significantly reduced. After the heat treatment process, a fine cryptocrystalline martensite structure is obtained in the steel matrix. The graphene in the inoculant has an in situ reaction with Cr to form Cr7C3, and a small amount of austenite is present at the edge of the particle. The hardness, wear rate and tensile strength of the bearing steel after inoculation and heat treatment reached 61.2 HRC, 0.1904% and 2247 MPa, respectively. It is worth noting that the impact toughness of GCr15 with inoculation reached 125.33 J/cm2, which is 150.91% higher than that of GCr15 without inoculation. The relationship between macro-performance and microstructure is also clarified in this manuscript.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. A review on data-driven fault severity assessment in rolling bearings10.1016/j.ymssp.2017.06.012 ↗
2. Further understanding of rolling contact fatigue in rolling element bearings - a review10.1016/j.triboint.2019.105849 ↗
3. Steels for bearings10.1016/j.pmatsci.2011.06.002 ↗
4. Study on microstructures and properties of carbide-free and carbide-bearing bainitic steels10.1016/j.msea.2017.12.108 ↗
5. Enhanced toughness of bearing steel by combining prior cold deformation with martensite pre-quenching and bainite transformation10.1016/j.matlet.2018.09.017 ↗
6. Effect of annealing on microstructure, phase composition and mechanical properties of thixo-cast 100Cr6 steel10.1016/j.matchar.2012.03.018 ↗
7. Wear and corrosion of niobium carbide coated AISI 52100 bearing steel10.1016/j.surfcoat.2015.08.036 ↗
8. Effect of microalloying with molybdenum and boron on the microstructure and mechanical properties of ultra-low-C Ti bearing steel10.1016/j.msea.2015.05.087 ↗
9. Improving impact toughness of high-C–Cr bearing steel by Si–Mo alloying and low-temperature austempering10.1016/j.matdes.2015.07.055 ↗
10. Microstructures and mechanical properties of a modified high-C–Cr bearing steel with nano-scaled bainite10.1016/j.msea.2014.12.121 ↗
11. Very high cycle fatigue properties of bearing steel with different aluminum and sulfur content10.1016/j.ijfatigue.2018.06.047 ↗
12. Strain-induced formation of a gradient nanostructured surface layer on an ultrahigh strength bearing steel10.1016/j.jmst.2017.12.012 ↗
13. Effect of Nb solute and NbC precipitates on dynamic or static recrystallization in Nb steels10.1016/S1006-706X(13)60020-5 ↗
14. Slurry erosion, sliding wear and corrosion behavior of martensitic stainless steel composites reinforced in-situ with NbC particles10.1016/j.wear.2018.09.013 ↗
15. Effect of TiC particle size on high temperature oxidation behavior of TiC reinforced stainless steel10.1016/j.apsusc.2019.02.138 ↗
16. Improved tribological properties of Si3N4/GCr15 sliding pairs with few layer graphene as oil additives10.1016/j.ceramint.2017.07.168 ↗
17. Thermal conductivity and scattering models for graphene: from intrinsic scattering of pristine graphene to strong extrinsic scattering of functionalized graphene10.1016/j.apsusc.2019.143739 ↗
18. Structure and properties of GCr15 modified by multiphase ceramic nanoparticles/Fe-C composite inoculants10.1016/j.msea.2018.09.074 ↗
19. The effect of amorphous nanocrystalline inoculants on structures and properties of high speed steel10.1088/2053-1591/aa75df ↗
20. Microstructure and properties' evaluation of W18Cr4V modified by Fe–Zr–Nb–N–B nano‐powder inoculants10.1002/srin.201600318 ↗
21. Effects of the nanostructured Fe-V-Nb modificators on the microstructure and mechanical properties of Si-Mn steel
22. Influence of high-energy ball milling on Mg-PSZ-reinforced TRIP steel-matrix composites synthesized by FAST/SPS10.1016/j.msea.2019.05.104 ↗
23. Preparation of in situ Al3Nb-NbB2-NbC/Al inoculant and its effect on microstructures and properties of weldable Al-Cu-Mn alloy10.1016/j.msea.2018.09.110 ↗
24. The finer things in X-ray diffraction data collection
25. The effect of prior cold rolling on the carbide dissolution, precipitation and dry wear behaviors of M50 bearing steel10.1016/j.triboint.2018.12.031 ↗
26. Effect of boron segregation on the surface crack of low carbon boron-bearing steel10.1016/j.rinp.2019.02.089 ↗
27. Development of and perspective on high-performance nanostructured bainitic bearing steel10.1016/j.eng.2018.11.024 ↗
28. Effect of ammonia addition on microstructure and wear performance of carbonitrided high carbon bearing steel AISI 5210010.1016/j.surfcoat.2019.01.019 ↗
29. Strength-toughness improvement of martensite-austenite dual phase deposited metals after austenite reversed treatment with short holding time10.1016/j.msea.2019.03.125 ↗
30. Intercritical tempering enables nanoscale austenite/ε-martensite formation in low-C medium-Mn steel: a pathway to control mechanical properties10.1016/j.msea.2018.08.082 ↗
31. Effect of transverse static magnetic field on microstructure and properties of GCr15 bearing steel in electroslag continuous casting process10.1016/j.msea.2016.02.075 ↗
32. Effects of rare earth elements on inclusions and impact toughness of high-carbon chromium bearing steel10.1016/j.jmst.2019.01.015 ↗
33. Improved microstructural homogeneity and mechanical property of medium manganese steel with Mn segregation banding by alternating lath matrix10.1016/j.msea.2017.11.046 ↗
34. Radiation-induced segregation in austenitic stainless steel type 304: effect of high fraction of twin boundaries10.1016/j.msea.2011.06.066 ↗
35. Decomposition characteristic of austenite retained in GCr15 bearing steel modified by addition of 1.3wt.% silicon during tempering10.1016/j.jmrt.2017.08.012 ↗
36. Preparation and microstructure of in situ CaB\r _{}6\r -Al\r _{}4\r Ca/Al composite inoculant ribbon and its refining and modifying effect on Al-10Si-0.3Mg alloy10.1002/adem.201800687 ↗
37. Enhanced stability of retained austenites in quenched 25SiMn2MoV steel by electro-pulsing current
38. The effects of W content on solid-solution strengthening and the critical Hall-Petch grain size in Ni-W alloy10.1016/j.surfcoat.2018.09.086 ↗