Controlling the high temperature mechanical behavior of Al alloys by precipitation and severe straining
Source abstract
Abstract
Abstract The aim of this work was to investigate the influence of the precipitate distribution on the microstructure and on the room and high temperature mechanical properties of an age-hardenable aluminium AA6082 alloy following severe straining by high-pressure torsion (HPT). With this goal, specimens in the as-cast and T6 peak-aged conditions were processed by HPT using 0.5, 1 and 5 turns at room temperature. At high strain levels (γ>100), similar saturation grain sizes (~250 nm), high-angle boundary fractions (~80%) and hardness values (Hv~160) were obtained for both initial conditions. Grain refinement led to significant strengthening and to good ductility values at room temperature. Analysis by TEM and EDS elemental mapping revealed that HPT processing of the as-cast condition led to fracture of the stable β-phase into many small precipitates located preferentially along grain boundaries and triple junctions. By contrast, HPT processing of the T6 peak-aged specimens revealed a partial dissolution of the needle-shaped nanoprecipitates. The different evolutions of the precipitate distributions following straining in the as-cast and peak-aged conditions gave rise to dramatic differences in the mechanical properties and the operative deformation mechanisms at warm temperatures. These results provide evidence that the high temperature mechanical behavior of age-hardenable Al alloys may be conveniently controlled by altering the precipitate distribution followed by severe straining.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Atomic model for GP-zones in a 6082 Al-Mg-Si system10.1016/S1359-6454(00)00302-5 ↗
2. The effect of coarse second-phase particles and fine precipitates on microstructure refinement and mechanical properties of severely deformed Al alloy10.1016/j.msea.2004.11.025 ↗
3. Strengthening study on 6082 Al alloy after combination of aging treatment and ECAP process10.1016/j.msea.2010.04.017 ↗
4. A TEM investigation on the effect of semisolid forming on precipitation processes in an Al-Mg-Si alloy10.1016/S1044-5803(02)00325-X ↗
5. Phase relations and precipitation in Al-Mg-Si alloys with Cu additions10.1016/S0079-6425(03)00031-8 ↗
6. Phase stability and structural relations of nanometer-sized, matrix-embedded precipitate phases in Al-Mg-Si alloys in the late stages of evolution10.1016/j.actamat.2006.02.034 ↗
7. Dynamic precipitation during severe plastic deformation of an Al-Mg-Si aluminium alloy10.1016/j.msea.2006.09.142 ↗
8. The effect of cold work on the precipitation kinetics of AA6111 aluminum10.1023/B:JMSC.0000044888.01854.e1 ↗
9. The effect of predeformation on the β″ and β′ precipitates and the role of Q′ phase in an Al–Mg–Si alloy; AA602210.1016/j.scriptamat.2005.04.013 ↗
10. Optimization of electrical conductivity and strength combination by structure design at the nanoscale in Al-Mg-Si alloys10.1016/j.actamat.2015.07.039 ↗
11. Grain refinement and superplastic flow in an aluminum alloy processed by high-pressure torsion10.1016/j.msea.2005.07.023 ↗
12. Precipitation kinetics in a severely plastically deformed 7075 aluminium alloy10.1016/j.actamat.2013.11.071 ↗
13. Using high-pressure torsion for metal processing: fundamentals and applications10.1016/j.pmatsci.2008.03.002 ↗
14. The microstructural characteristics of ultrafine-grained nickel10.1016/j.msea.2004.09.030 ↗
15. Nanostructural hierarchy increases the strength of aluminium alloys10.1038/ncomms1062 ↗
16. Observations of high strain rate superplasticity in commercial aluminum alloys with ultrafine grain sizes10.1016/S1359-6462(97)00387-4 ↗
17. Using ECAP to achieve grain refinement, precipitate fragmentation and high strain rate superplasticity in a spray-cast aluminum alloy10.1016/S1359-6454(03)00433-6 ↗
18. Severe plastic deformation as a processing tool for developing superplastic metals10.1016/j.jallcom.2003.10.065 ↗
19. On the origin of the extremely high strength of ultrafine-grained Al alloys produced by severe plastic deformation10.1016/j.scriptamat.2010.07.014 ↗
20. Strength, grain refinement and solute nanostructures of an Al-Mg-Si alloy (AA6060) processed by high-pressure torsion10.1016/j.actamat.2013.10.022 ↗
21. Atomic-scale analysis of the segregation and precipitation mechanisms in a severely deformed Al-Mg alloy10.1016/j.actamat.2014.03.033 ↗
22. Enhanced grain refinement of an Al-Mg-Si alloy by high-pressure torsion processing at 100°C10.1016/j.msea.2012.05.063 ↗
23. Microstructure of two-phase Al–1.7at% Cu alloy deformed by equal-channel angular pressing10.1016/S1359-6454(00)00308-6 ↗
24. Influence of ECAP on precipitate distributions in a spray-cast aluminum alloy10.1016/j.actamat.2004.10.026 ↗
25. High strain rate superplasticity at intermediate temperatures of the Al 7075 alloy severely processed by equal channel angular pressing10.1016/j.jallcom.2011.07.076 ↗
26. Achieving microstructures prone to superplastic deformation in an Al–Zn–Mg–Cu alloy by equal channel angular pressing10.1016/j.jallcom.2012.08.084 ↗
27. Apps · Acta Mater. · 2005 · 53 · 49910.1016/j.actamat.2004.09.042 ↗
28. Zhilyaev · Scr. Mater. · 2007 · 57 · 76310.1016/j.scriptamat.2007.06.029 ↗
29. On the origin of strain softening during deformation of aluminum in torsion to large strains10.1007/s11661-003-0174-1 ↗
30. Modelling texture development during equal channel angular extrusion of aluminium10.1016/S1359-6454(02)00055-1 ↗
31. Theory of torsion texture development10.1016/0001-6160(84)90050-6 ↗
32. Microstructural evolution and electro-resistivity in HPT nickel10.1016/j.msea.2012.07.010 ↗
33. The evolution of homogeneity in an aluminum alloy processed using high-pressure torsion10.1016/j.actamat.2008.06.036 ↗
34. Effect of short-term annealing on the microstructures and flow properties of an Al–1% Mg alloy processed by high-pressure torsion10.1016/j.msea.2014.07.018 ↗
35. Nanostructure and related mechanical properties of an Al-Mg-Si alloy processed by severe plastic deformation10.1080/09500830802186938 ↗
36. Influence of equal-channel angular pressing on precipitation in an Al–Zn–Mg–Cu alloy10.1016/j.actamat.2009.03.017 ↗
37. Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy10.1016/j.ultramic.2010.11.013 ↗
38. Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing10.1016/j.actamat.2004.06.017 ↗
39. Grain elongation and anisotropic grain growth during superplastic deformation in an AlMgMnCu alloy10.1016/S1359-6454(97)00032-3 ↗
40. Microstructural control of an Al-Mg-Si alloy using equal-channel angular pressing10.4028/www.scientific.net/MSF.396-402.333 ↗
41. Formation of nanograined structure and decomposition of supersaturated solid solution during high pressure torsion of Al-Zn and Al-Mg alloys10.1016/j.actamat.2004.06.006 ↗
42. Grain boundary films in Al-Zn alloys after high pressure torsion10.1016/j.scriptamat.2013.09.019 ↗
43. Grain boundary phenomena in an ultrafine-grained Al–Zn alloy with improved mechanical behavior for micro-devices10.1002/adem.201300450 ↗