Fracture properties of multiphase alloy MP35N
Source abstract
Abstract
Abstract This paper addresses the fracture properties of commercially cold-drawn (53%) MP35N (35% Co, 35% Ni, 20% Cr, and 10% Mo) in both the cold-worked and the cold-worked and aged conditions. MP35N is a superalloy that exhibits a remarkable combination of high strength (about 2 GPa) and high fracture toughness (about 100 MPa m ). The fracture toughness of MP35N was investigated systematically, with particular attention to the influence of the post deformation aging heat treatment, the sample thickness, the orientation of crack plane and the direction of crack propagation with respect to the drawing direction in the sample. These measurements yielded the following important results: (1) The plane strain fracture toughness of the commercially cold-drawn MP35N is about 120 MPa m , and is about 110 MPa m in the cold-drawn and aged condition. (2) The plane stress fracture toughness values for the cold-drawn MP35N were significantly lower than the corresponding values for the cold-drawn and aged material, in spite of the fact that the later had a higher strength value. (3) The direction of the crack propagation did influence the fracture toughness, reducing its value significantly in T–L direction, as compared with values in T–T and L–T directions.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. G.D. Smith, U.S. Patents 3,562,024 and 3,356,542 (1967).
2. Asgari · Met. Mater. Trans. A · 1997 · 28 · 178110.1007/s11661-997-0109-3 ↗
3. Singh · Met. Trans. A · 1992 · 23 · 30710.1007/BF02660873 ↗
4. Asgari · Acta Mater. · 1998 · 46 · 579510.1016/S1359-6454(98)00235-3 ↗
5. Shaji · Mater. Sci. Eng. · 1999 · A272 · 37110.1016/S0921-5093(99)00502-X ↗
6. El-Danaf · Int. J. Plast. · 2001 · 17 · 124510.1016/S0749-6419(00)00090-5 ↗
7. F.R. Stonesifer, H.L. Smith, H.E. Romine, “Evaluation of Three Materials as Candidates for Lift-Pad Studs in an Ocean Environment”, Naval Research Laboratory Report 2068 (1969), Washington, D.C.
8. Metcut Research Associates Inc., Laboratory Report 89-18630-1, KIC Testing on MP35N for Latrobe Steel Co., December (1972), Cincinnati, OH.
9. R.L. Peterson, Plane Strain Fracture Toughness Test Report, TerraTek Systems, Salt Lake City, November 1990.
10. SPS Technologies, Inc., Private Communication of Results on Tests Conducted at Batelle, Naval Research Lab, and Climax, March 1982, Jenkintown, PA.
11. J.L. Maloney, Fracture Toughness of MP35N and MP159 Alloys, Internal Report, Latrobe Steel Company, Latrobe, PA, May 1982.
12. Plane strain fracture toughness of MP35N in aged and unaged conditions measured using modified CT specimens10.1016/S0921-5093(02)00167-3 ↗
13. ASTME 399-90, “Test Method for Plain-Strain Fracture Toughness of Metallic Materials” American Society for Testing Materials, Philadelphia, PA, 1990.
14. Anderson · 1995