journal article·2002-04

A study on the development and wear characteristics of rheocast Al–5Cu–2Pb alloy and Al–5Cu/Pb–18Sn wire composites

V Agarwala, K.G Satyanarayana, R.C Agarwala, Rajnish Garg

Publisher page

Abstract

Abstract With renewed search for a low cost material for bearing application in place of conventional and expensive Al–Sn alloy, this paper describes development of an aluminium alloy Al–5wt.%Cu–2wt.%Pb alloy and Al–5wt.%Cu/Pb–18wt.% Sn wire composite by different types of casting routes. Wear characteristics and microstructural analysis of both alloy and composites have been determined. It is found that rheocast Al–5Cu–2Pb has a morphology of Pb rich phase in the form of partly continuous nature along the grain boundaries of spherical α-Al particles resulting in good wear resistance. Bulk wear in the rheocast Al–5Cu–2Pb alloy increases with increasing sliding distance from 38.5 to 92.4 m with severe to mild wear transition occurring at a sliding distance of 46.2 m for a given applied load of 18.1 kg. Also the wear increases with increasing applied load from 18.1 to 24.4 kg for a constant sliding velocity and it increases continuously with increasing sliding velocity at a constant applied load. These results are explained in terms of smearing layer of lead due to frictional heat generated both at high applied loads and at high sliding velocities. Bulk wear and roughness of the rheocast Al–5Cu–2Pb alloy have been correlated through an equation of the type W=a R b , where a and b are constants independent of both applied load and sliding velocity. In the case of Al–5Cu/Pb–18Sn wire composite, containing 0.51–1.95 Pb content, bulk wear ∼0.7×10 −6 kg at a sliding velocity of 25.67×10 −2 m s −1 and applied load of 19.4 kg f −1 was found and it is ∼5 times better than that of rheocast Al–10Pb alloy. This study suggests that for Al–5Cu matrix produced by fast cooling rates are better suited for bearing applications. Reduction in the lead content is also more suitable from the environmental point of view.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. R.W. Dayton (Ed.), Sleeve Bearing Materials, ASM, Cleveland, OH, 1949.
2. Neale · 1973 · C1
3. Pratt · Inst. Met. Rev. · 1973 · 18 · 4210.1179/imr.1973.18.1.42 ↗
4. Kragelsky · 1981 · I · 223
5. Tiwari · 1985 · 139
6. Mondolfo · 1976 · 345
7. Avaraamov · Mater. Sci. Heat Treat. · 1985 · 26 · 54310.1007/BF00706716 ↗
8. Evans · Tin Uses · 1980 · 126 · 8
9. Lansdown · 1982 · 126
10. Vijaya Agarwala, K.G. Satyanarayana, Unpublished work.
11. MacKay · Met. Progr. · 1977 · 111 · 32
12. K. Nishiyama, Y. Kotami, K. Miyama, S. Umakawa, Jpn. Soc. Powder Metall., (1993) 64510.2497/jjspm.40.645 ↗
13. Appich · Met. Eng. Quart. · 1971 · 11 · 33
14. Borgunov · Russ. Const. Prod. · 1973 · 9 · 533
15. Pathak · Met. Tech. · 1979 · 6 · 44210.1179/030716979803276822 ↗
16. Younchang · Mater. Sci. Eng. · 1988 · 98 · 11910.1016/0025-5416(88)90139-5 ↗
17. Sunil Mohan, Ph.D. Thesis, Dept. Met. Engg., UOR, Roorkee, India, 1989.
18. Ohashi · J, Inst. Met. · 1992 · 42 · 568
19. Berrenberg · Mater. Sci. Eng. · 1993 · A173 · 41310.1016/0921-5093(93)90255-D ↗
20. Ichikawa · Trans. JIM · 1987 · 28 · 13510.2320/matertrans1960.28.135 ↗
21. Ichikawa · Trans. JIM · 1987 · 28 · 43410.2320/matertrans1960.28.434 ↗
22. Ishizuka · Trans. JIM · 1985 · 26 · 51310.2320/matertrans1960.26.513 ↗
23. Ichikawa · Trans. JIM · 1985 · 28 · 14510.2320/matertrans1960.28.145 ↗
24. Ojha · Powder Met. Int. · 1993 · 2 · 65
25. Pathak · Bull. Mater. Sci. · 1995 · 18 · 97510.1007/BF02745184 ↗
26. Fuxiao · Bull. Mater. Sci. · 1999 · 22 · 95910.1007/BF02745686 ↗
27. Tunsiker · 1949 · 82
28. Tiwari · Met. Tech. · 1983 · 10 · 41310.1179/030716983803291875 ↗
29. Ikeda · J. Jpn. Inst. Light Met. · 1985 · 35 · 2010.2464/jilm.35.20 ↗
30. Sunil Mohan, Vijaya Agarwala, Subrat Roy, Wear 140 (1990) 83.10.1016/0043-1648(90)90123-R ↗
31. Timken Wear and Lubricant Testing Machine, Mad et al 930, MST-48651, Mannual UK.
32. Doherts · Mater. Sci. Eng. · 1984 · 65 · 18110.1016/0025-5416(84)90211-8 ↗
33. Molenaar · J. Mater. Sci. · 1987 · 22 · 105710.1007/BF01103551 ↗
34. Soda · Trans. ASME J. Lubrication Techn. · 1978 · 100 · 49210.1115/1.3453261 ↗
35. Sada · 1985 · 623
36. Lim · Acta Met. · 1987 · 35 · 110.1016/0001-6160(87)90209-4 ↗
37. T. Hirst, K.R. Macklenburg, R.J. Benzing, In: R.G. Boyer (Ed.), Testing for Adhesive Wear, ASM STP 615 (1976) 12.
38. Jasim · Trans. JIM · 1984 · 37 · 581
39. Jasim · Wear · 1982 · 82 · 37710.1016/0043-1648(82)90230-7 ↗
40. Bucklay · 1981 · 315
41. H. Shou, R.D. Arnell, Proc. Inf. Conf. on Tribology-Friction, Lubrication wear, Fifty Years, Vol. II, Mech. Engg publication, London, 1987, p. 657.
42. F.F. Ling, E.E. Klaus, R.S. Fien (Eds.), Boundary Lubrication, ASME, New York, 1969, p. 490.
43. Sugishita · Wear · 1981 · 66 · 20910.1016/0043-1648(81)90115-0 ↗
44. T.S. Eyre, In: R.C. Malhotra and J.P. Sharma (Eds.), Proc. First World Conf. in Industrial Trib., New Delhi, 1972, p. F9.1.
45. Leach · Wear · 1985 · 85 · 25710.1016/0043-1648(83)90068-6 ↗
46. Giltrow · Composites · 1973 · 4 · 5510.1016/0010-4361(73)90749-0 ↗
47. S.B. Ainbinder, N.G. Andreyeva, Euro. Trib. 81 (1982) 7, Elsevier, New York.
48. Vijaya Agarwala, A Report on the Study of the wear characteristics of rheocast leaded Aluminium alloys, submitted to CSIR, New Delhi, 1994.