Effect of trace solute titanium on plastic deformation of α-(Fe, Cr) single-crystal micropillars fabricated from 18Cr ferritic stainless steel
Source abstract
Abstract
Abstract The effect of a trace amount (~0.1 at.%) of solute Ti on the compression response of cylindrical single-crystal micropillars fabricated from a 18Cr ferritic stainless steel was investigated. The micropillars of the solution-treated steel samples were fabricated on a special grain with different diameter ranges (d = 2–3 μm or 5–6 μm). By this process, the flow stress required for slip initiation (corresponding to the yield stress) and its strain rate dependence could be determined. The compression tests on the micropillars revealed that Ti addition (solute Ti in the α-(Fe, Cr) ferrite matrix) has a slight effect on the activated slip system and stress level required for the slip initiation of 18Cr steel specimens with two different sizes. In addition, the strain rate sensitivity (m) of the yield stress at an offset strain of 0.2% (0.2% proof stress) in the small micropillars (d = 2–3 μm) of the micron-sized 18Cr steel specimens decreased slightly (from 0.12 to 0.08), owing to the Ti addition. However, the m value (0.04) of the large micropillars (d = 5–6 μm) of the 18Cr steel is unaffected by Ti addition and is equivalent to the m value measured for millimeter-sized specimens (conventional bulk specimens). The low activation volume (v*) values (18–19 b3) were obtained for the small micropillars of both the 18Cr and Ti-added steels. For the large specimens, the v* value of the 18Cr steel decreased slightly from 50 b3 to 46 b3 owing to the Ti addition and is close to the value obtained from the millimeter-sized specimens. These results indicate that the trace amount of solute Ti has a slight effect on the thermal activation process for controlling the dislocation motion in the 18Cr ferritic stainless steels. The intriguing low activation volume in the small micropillars is discussed in comparison with the results of micron-scale specimens of various bcc metals and alloys.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · Metal and Thin Film Mechanics · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Study on microstructure and mechanical characteristics of low-carbon steel and ferritic stainless steel joints10.1016/j.msea.2014.04.065 ↗
2. Hot deformation behavior and microstructure evolution of a stabilized high-Cr ferritic stainless steel10.1016/j.msea.2013.01.077 ↗
3. Precipitation sequence in niobium-alloyed ferritic stainless steel10.1088/0965-0393/12/2/008 ↗
4. Recent developments in stainless steels10.1016/j.mser.2009.03.001 ↗
5. Metals Handbook Volume 1
6. Ultra-pure ferritic stainless steels-grade, refining operation, and application10.1016/S1006-706X(07)60053-3 ↗
7. Lula · 1980
8. The influence of chromium on the mechanical properties of plain chromium steels
9. Some considerations on the toughness properties of ferritic stainless steels—a brief review10.1016/0308-0161(93)90114-9 ↗
10. Microstructure and texture of Nb + Ti stabilized ferritic stainless steel10.1016/j.matchar.2008.03.018 ↗
11. Effect of titanium on the ductility of 26% chromium, low interstitial ferritic stainless steel10.1179/030716974803288086 ↗
12. Effect of titanium carbide precipitates on the ductility of 30 mass% Chromium ferritic steels10.2320/matertrans.44.1153 ↗
13. Review of stabilization of ferritic stainless steel10.1179/mst.1996.12.2.126 ↗
14. Effect of Ti content on grain size and mechanical properties of UNSS44100 ferritic stainless steel10.1016/j.msea.2016.08.070 ↗
15. Change in dislocation mobility with Ni content in ferritic steels and its effect on brittle-to-ductile transition10.2355/tetsutohagane.98.667 ↗
16. Brittle-to-ductile transition in nickel-free austenitic stainless steels with high nitrogen10.2355/tetsutohagane.98.237 ↗
17. Effect of crack-tip dislocation on fracture toughness
18. Sample dimensions influence strength and crystal plasticity10.1126/science.1098993 ↗
19. Overciew on micro- and nanomechanical testing: new insights in interface plasticity and fracture at small length scales10.1016/j.actamat.2017.06.019 ↗
20. Crystal structures and mechanical properties of Fe-Zn intermetallic compounds formed in the coating layer of galvannealed steels10.2355/isijinternational.ISIJINT-2018-066 ↗
21. Size effects in Al nanopillars: single crystalline vs. bicrystalline10.1016/j.actamat.2011.03.065 ↗
22. Anomalous size-dependent strength in micropillar compression deformation of commercial-purity aluminum single-crystals10.1016/j.msea.2019.138710 ↗
23. Temperature and orientation effects on the deformation mechanisms of α-Fe micropillars10.1016/j.actamat.2017.03.006 ↗
24. Strain rate sensitivity of flow stress measured by micropillar compression test for 18Cr ferritic-steel single-crystals10.2355/isijinternational.ISIJINT-2019-448 ↗
25. The size dependent strength of Fe, Nb and V micropillars at room and low temperature10.1016/j.mtla.2019.100424 ↗
26. Effect of grain refinement on tensile properties and electrochemical behavior of Fe-18.5%Cr ferritic stainless steel10.1016/j.matchemphys.2020.123089 ↗
27. Size dependence of mechanical properties of gold at the micron scale in the absence of strain gradients10.1016/j.actamat.2004.12.031 ↗
28. Measurement of Young's modulus of anisotropic materials using microcompression testing10.1557/jmr.2012.18 ↗
29. The relation between load and penetration in the axisymmetric boussinesq problem for a punch of arbitrary profile10.1016/0020-7225(65)90019-4 ↗
30. Theory of tensile test10.1016/0001-6160(67)90211-8 ↗
31. Dynamic deformation behavior of ultrafine-grained iron produced by ultrahigh strain deformation and annealing10.1016/j.scriptamat.2011.01.026 ↗
32. A study on temperature and strain rate dependences of yield stress at low temperatures in pure iron and Fe-Cr Alloys10.2355/tetsutohagane1955.57.6_954 ↗
33. Plasticity in small-sized metallic system: intrinsic versus extrinsic size effect10.1016/j.pmatsci.2011.01.005 ↗
34. Influence of orientation on the size effect in bcc pillars with different critical temperatures10.1016/j.msea.2010.10.073 ↗
35. Specimen size and shape dependent yield strength in micropillar compression deformation of Mo single crystals10.1016/j.ijplas.2017.02.014 ↗
36. Correlation between critical temperature and strength of small-scale bcc pillars10.1103/PhysRevLett.103.105501 ↗
37. Micro-compression studies of face-centered cubic and body-centered cubic highentropy alloys: size-dependent strength, strain rate sensitivity, and activation volumes10.1016/j.msea.2020.139429 ↗
38. Dominating deformation mechanisms in ultrafine-grained chromium across length scales and temperature10.1016/j.actamat.2017.08.043 ↗
39. 1994
40. Refractory high-entropy alloys10.1016/j.intermet.2010.05.014 ↗
41. Temperature dependence of activation volume on cu content of ultra-low carbon steel10.1080/14786435.2017.1359423 ↗