journal article·2020-09

Zr55Cu30Al10Ni5 amorphous alloy sheets with large plasticity fabricated by twin-roll strip casting

C.Y. Zhang, G. Yuan, Y.X. Zhang, Y. Wang, F. Fang, J. Kang, G.D. Wang

Publisher page

Abstract

Abstract Zr55Cu30Al10Ni5 (at.%) amorphous sheets with thickness of ~0.5 mm and width of ~75 mm were successfully fabricated by twin-roll strip casting. The amorphous alloy sheets fabricated using a high rolling force exhibited a high-energy state, a high free-volume content, and structural inhomogeneity, which led to an engineering strain greater than 62% in compression at room temperature. This study provides an effective method for fabricating large amorphous alloy sheets with good plasticity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. Bulk amorphous FC20 (Fe–C–Si) alloys with small amounts of B and their crystallized structure and mechanical properties10.1016/S1359-6454(99)00394-8 ↗
2. Mechanical behavior of amorphous alloys10.1016/j.actamat.2007.01.052 ↗
4. Microstructure and tensile properties of twin-roll cast Mg–Zn–Mn–Al alloys10.1016/j.scriptamat.2007.07.013 ↗
5. Cladding of Mg alloy with Al by twin-roll casting10.1016/j.scriptamat.2011.01.013 ↗
6. Sheet fabrication of bulk amorphous alloys by twin-roll strip casting10.1016/j.scriptamat.2005.05.018 ↗
7. Continuous casting of thick Fe-base glassy plates by twin-roller melt-spinning10.1016/j.msea.2006.02.341 ↗
8. Continuous fabrication of bulk amorphous alloy sheets by twin-roll strip casting10.1016/j.intermet.2006.01.039 ↗
9. Mechanical properties of Fe–Ni–Cr–Si–B bulk glassy alloy10.1016/j.msea.2006.02.304 ↗
10. Twin-roll strip casting of iron-base amorphous alloys10.2320/matertrans.MJ200711 ↗
11. A rapid quenching technique for the preparation of thin uniform films of amorphous solids10.1063/1.1684774 ↗
12. Trans. Modelling and simulation of twin-roll casting of bulk metallic glasses
13. Dynamic relaxations and relaxation-property relationships in metallic glasses10.1016/j.pmatsci.2019.03.006 ↗
14. Evolution of shear bands, free volume and hardness during cold rolling of a Zr-based bulk metallic glass10.1016/j.actamat.2013.10.035 ↗
15. Microstructure and microhardness evolutions of Cu47.5Zr47.5Al5 bulk metallic glass processed by rolling10.1016/j.scriptamat.2008.05.023 ↗
16. Free-volume evolution and its temperature dependence during rolling of Cu60Zr20Ti20 bulk metallic glass10.1063/1.2037858 ↗
17. Thermomechanical processing of metallic glasses: extending the range of the glassy state10.1038/natrevmats.2016.39 ↗
18. Shear bands in metallic glasses10.1016/j.mser.2013.04.001 ↗
19. Remarkable improving plasticity of a brittle Zr-based bulk metallic glass by a high rheological rate forming method in centesimal seconds10.1016/j.matlet.2015.11.017 ↗
20. Mechanical property and fracture behavior of strip cast Zr-base BMG alloy containing crystalline phase10.1016/j.intermet.2004.04.022 ↗
21. Impact fracture energy of bulk amorphous Zr55Al10Cu30Ni5 alloy10.2320/matertrans1989.37.1726 ↗
22. Processing of bulk metallic glass10.1002/adma.200902776 ↗
23. Formation of glasses from liquids and biopolymers10.1126/science.267.5206.1924 ↗
24. Super plastic bulk metallic glasses at room temperature10.1126/science.1136726 ↗
25. Effect of rolling deformation on the microstructure of bulk Cu60Zr20Ti20 metallic glass and its crystallization10.1016/j.actamat.2006.05.030 ↗
26. Mechanically driven phase separation and corresponding microhardness change in Cu60Zr20Ti20 bulk metallic glass10.1063/1.1862329 ↗
27. Multiple twinning and variant-variant transformations in martensite: phasefield Approach10.1103/PhysRevB.88.054113 ↗
28. Multiphase phase field theory for temperature-and stress-induced phase Transformations10.1103/PhysRevB.91.174109 ↗
29. Micromechanical modeling of martensitic transformation induced plasticity (TRIP) in austenitic single crystals10.1016/S0749-6419(99)80000-X ↗
30. Effects of pressure on structure and mechanical property in monatomic metallic glass10.1016/j.jnoncrysol.2017.03.013 ↗
31. Anomalous structure-property relationships in metallic glasses through pressure-mediated glass formation10.1103/PhysRevB.93.140204 ↗
32. Polyamorphism in a metallic glass10.1038/nmat1839 ↗
33. Embrittlement of a bulk metallic glass due to sub-Tg annealing10.1016/j.actamat.2004.11.040 ↗
34. Changes in short-range order of Zr55Cu30Al10Ni5 and Zr55Cu20Al10Ni10Ti5 BMGs upon annealing10.1016/j.jallcom.2010.07.001 ↗
35. Mechanical properties and ion irradiation of bulk amorphous Zr55Cu30Al10Ni5 alloy10.1016/j.jnoncrysol.2007.04.013 ↗
36. Tunable tensile ductility of metallic glasses with partially rejuvenated amorphous structures10.1016/j.actamat.2019.03.007 ↗
37. Heterogeneity of a Cu47.5Zr47.5Al5 bulk metallic glass10.1063/1.2171472 ↗
38. Thermomechanical processing of metallic glasses: extending the range of the glassy state10.1038/natrevmats.2016.39 ↗
39. Shear band spacing under bending of Zr-based metallic glass plates10.1016/j.actamat.2004.01.034 ↗
40. A microscopic mechanism for steady state inhomogeneous flow in metallic glasses10.1016/0001-6160(77)90232-2 ↗
41. Plastic deformation in metallic glasses10.1016/0001-6160(79)90055-5 ↗