Assessment of back stress and load transfer approaches for rationalizing creep of short fiber reinforced aluminum alloys
Source abstract
Abstract
Abstract Creep data from a model Al–Zn alloy reinforced with Saffil short fibers were evaluated following the threshold stress and the load transfer approaches usually employed in the creep data analysis of metal matrix composites. Experiments indicate that the short fiber reinforced material creeps with a stress exponent of 10 while the matrix stress exponent is 5. Procedures published in the literature which yield natural stress exponents and threshold stresses which decrease with increasing temperature were reproduced; however, threshold values corresponding to natural stress exponents cannot be physically justified. The procedures considered in this paper yielded no precise results. Several combinations of stress exponents/threshold values and activation energies are shown to satisfy the procedural requirements. Therefore load transfer and threshold approaches should always be combined with microstructural investigations before an attempt is made to rationalize creep behavior of MMCs.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. Chadek · Mater. Sci. Eng. A · 1995 · 190 · 910.1016/0921-5093(94)09605-V ↗
2. Li · Acta Mater · 2003 · 47 · 339510.1016/S1359-6454(99)00219-0 ↗
3. Rösler · Acta Mater · 2000 · 48 · 355310.1016/S1359-6454(00)00109-9 ↗
4. Dlouhy · Acta Mater · 1995 · 43 · 53510.1016/0956-7151(94)00255-G ↗
5. W.D. Nix, B. Ilschner, in: P. Haasen, V. Gerold, G. Kostorz (Eds.), Proceedings of the Fifth International Conference on the Strength of Metals and Alloys (ICSMA 5), vol. 3, Pergamon Press, Oxford, 1980, pp. 1503–1530.10.1016/B978-1-4832-8412-5.50243-5 ↗
6. A. Yawny, G. Kausträter, R. Valek, J. Scürhoff, B. Skrotzki, G. Eggeler, in: J.D. Parker (Ed.), Creep and Fracture of Engineering Materials and Structures, The Institute of Materials, London, 2001, pp. 219–228.
7. Dlouhy · Prac. Metallogr · 1995 · 30 · 17210.1515/pm-1993-300403 ↗
8. W. Blum, in: H. Mughrabi (Ed.), Materials Science and Technology, Plastic Deformation and Fracture of Materials, vol. 6, VCH, Weinhein, 1993, p. 392.
9. König · Acta Metall · 1977 · 25 · 153110.1016/0001-6160(77)90084-0 ↗
10. Lund · Acta Metall · 1976 · 24 · 46910.1016/0001-6160(76)90068-7 ↗
11. U.F. Kocks, A.S. Argon, M.F. Ashby, Progr. Mater. Sci. 19 (1975).
12. Mukherjee · Trans. Am. Soc. Met · 1969 · 62 · 155
13. J. Schürhoff, A. Yawny, B. Skrotzki, G. Eggeler, in preparation.