journal article·2020-07

Thermal fatigue testing of laser powder bed fusion (L-PBF) processed AlSi7Mg alloy in presence of a quasi-static tensile load

Zahra Sajedi, Riccardo Casati, Maria Cecilia Poletti, Mateusz Skalon, Maurizio Vedani

Publisher page

Abstract

Abstract The AlSi7Mg (A357) alloy is a suitable material to be used in different industrial applications. Even though the majority of parts is produced by casting, a large interest is raising on laser additive manufacturing of these alloys owing to their good processability. Service conditions of several applications, including cylinder heads and exhaust manifolds, cause the alloy to undergo fluctuating thermal and mechanical loads. The thermal fatigue of A357 alloy processed by Laser Powder Bed Fusion is here investigated using a Gleeble® 3800 equipment. The material is thermo-mechanically tested in the artificially aged condition. Microstructural and mechanical behavior of the alloy was investigated and it was found that by keeping fixed the maximum and minimum temperatures of thermal cycles between 100 and 280 °C, the fatigue life of the alloy deteriorates significantly by increasing the mechanical load from 90 to 120 MPa. Fractographic analyses showed the occurrence of ductile fracture nucleated from large process-induced pores and numerous fine dimples created due to plastic deformation. Secondary cracks were observed on the fracture surface of samples, which nucleated and propagated from large cavities and micro-dimples. Results based on the analysis of the elasto-plastic behavior of the material at high temperature showed that the inelastic strain of the broken samples was about 5 times higher than that of the run-out samples. Hardness drop occurred in all specimens after thermal fatigue experiments due to the coarsening of strengthening phases and modification of the Si-rich particles.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · High Entropy Alloys Studies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (49)

Show source-provided references
1. The metallurgy and processing science of metal additive manufacturing10.1080/09506608.2015.1116649 ↗
2. Very high cycle fatigue and fatigue crack propagation behavior of selective laser melted AlSi12 alloy10.1016/j.ijfatigue.2016.06.003 ↗
3. Design for additive manufacturing: trends, opportunities, considerations, and constraints10.1016/j.cirp.2016.05.004 ↗
4. Effects of defects on mechanical properties in metal additive manufacturing: a review focusing on X-ray tomography insights
5. Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones10.1016/j.actamat.2016.02.014 ↗
6. Investigation into spatter behavior during selective laser melting of AISI 316L stainless steel powder10.1016/j.matdes.2015.08.086 ↗
7. On morphological surface features of the parts printed by selective laser melting (SLM)
8. Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing10.1016/j.jmatprotec.2014.06.005 ↗
9. Spatter and oxide formation in laser powder bed fusion of Inconel 718
10. Additive manufacturing of metallic components – process, structure and properties10.1016/j.pmatsci.2017.10.001 ↗
11. Kaufman · 2004 · 1
12. Fatigue properties and micromechanism of fracture of an alsimg0.6 cast alloy used in diesel engine cylinder head10.1016/j.proeng.2010.03.082 ↗
13. Selective laser melting of AlSi10Mg alloy: process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
14. Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting10.1016/j.ijfatigue.2016.06.002 ↗
15. Mechanical properties of AlSi10Mg produced by selective laser melting10.1016/j.phpro.2012.10.059 ↗
16. Effect of different heat treatment routes on microstructure and mechanical properties of AlSi7Mg, AlSi10Mg and Al-Mg-Zr-Sc alloys produced by selective laser melting
17. Angeloni · 2012
18. Bartsch · 1993 · 90
19. Thermomechanical fatigue: mechanisms and practical life analysis
20. Hazime · 2019
21. Thermomechanical fatigue---damage mechanisms and mechanism-based life prediction methods10.1007/BF02717131 ↗
22. Low cycle thermal fatigue of aluminum alloy cylinder head in consideration of changing metrology microstructure10.1016/j.proeng.2010.03.083 ↗
23. Application of cast Al–Si alloys in internal combustion engine components10.1179/1743280413Y.0000000027 ↗
24. Thermomechanical fatigue of cast aluminium alloys for cylinder head applications–experimental characterization and life prediction10.1016/j.proeng.2010.03.190 ↗
25. Thermo-mechanical fatigue influence of copper and silicon on hypo-eutectic Al–Si–Cu and Al–Si–Mg cast alloys used in cylinder heads10.1016/j.ijfatigue.2016.02.017 ↗
26. Aging response of an A357 Al alloy processed by selective laser melting
27. A model for thermal fatigue in an aluminium casting alloy10.1016/0142-1123(95)00009-I ↗
28. Thermo-mechanical fatigue life assessment of aluminium components using the damage rate model of Sehitoglu10.1016/j.ijfatigue.2007.01.054 ↗
29. Simulation and evaluation of thermal fatigue cracking of hot work tool steels10.1016/j.ijfatigue.2004.03.005 ↗
30. Thermal fatigue testing of chromium martensitic hot-work tool steel after different austenitizing treatments10.1016/j.jmatprotec.2004.04.158 ↗
31. Thermal and thermo-mechanical fatigue of structural alloys10.31399/asm.hb.v19.a0002391 ↗
32. Description of the deformation process under thermo-mechanical fatigue
33. Overview of aluminum alloy mechanical properties during and after fires10.1186/s40038-015-0007-5 ↗
34. Handbook, A. S. M (n.d.). Vol. vol. 2: Properties and Selection: Nonferrous Alloys and Special–Purpose Materials. 1990, ASM International.
35. DSC analyses of the precipitation behavior of two Al–Mg–Si alloys naturally aged for different times10.1016/S0167-577X(98)00118-9 ↗
36. Effect of pre-ageing on the precipitation behaviors and mechanical properties of Al-7Si-Mg alloys
37. Precipitation sequence of an aged Al-Mg-Si alloy10.2298/JMMB1002171F ↗
38. Effect of natural aging and preaging on subsequent precipitation process of an AI-Mg-Si alloy with high excess silicon10.1179/mst.1997.13.11.905 ↗
39. Effects of platform pre-heating and thermal-treatment strategies on properties of AlSi10Mg alloy processed by selective laser melting
40. Damage · 2010 · 319
41. Effects of powders and process parameters on density and hardness of A357 aluminum alloy fabricated by selective laser melting
42. Selective laser melting of metal powder of steel 316110.1088/1757-899X/142/1/012071 ↗
43. Microstructural and small-scale characterization of additive manufactured AlSi10Mg alloy10.1007/s42452-019-0270-5 ↗
44. New aluminum alloys specifically designed for laser powder bed fusion: a review10.3390/ma12071007 ↗
45. Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties and fracture mechanism10.1016/j.msea.2016.03.088 ↗
46. Metal alloys for fusion-based additive manufacturing10.1002/adem.201700952 ↗
47. Varestraint testing of selective laser additive manufactured alloy 718—influence of grain orientation10.3390/met9101113 ↗
48. EBSD texture analysis of an AlCuMg alloy for different solidification rates
49. Microstructure and solidification crack susceptibility of Al 6014 molten alloy subjected to a spatially oscillated laser beam10.3390/ma11040648 ↗