Micromechanical characterization of hard phases by means of instrumented indentation and scratch testing
Source abstract
Abstract
Abstract Several hard phases were examined by indentation testing and scratch testing to provide a consistently evaluated database on the mechanical properties and deformation characteristics of hard phases. The analysis of indentations was conducted carefully so that the same method is applicable for hard phases with differing properties. To check whether an influence by the indentation size effect (ISE) is present or not, the Nix-Gao method was used to compute a macroscopic, corrected hardness. Additionally, the possible influence of the surrounding matrix material on the measurements was evaluated. The topography of scratch grooves during scratch tests was determined using a confocal laser scanning microscope. Quantitative information for clearer insights on the deformation characteristics can be acquired with this technique. An indentation size effect was verified to some extent for metallically bonded hard phases. Although the ISE does not have the same magnitude as in metals, it has to be considered if instrumented indentation is used to obtain accurate parameters from hard phases. Matrix effects were also observed and were accounted for. The deformation during indentation and scratch testing showed good correlation between the mechanical parameters and the deformation behavior during scratching. With increasing hardness, the hard phases generally showed more microchipping and deformed elastically to a higher degree. Covalently bonded hard phases yielded the highest hardnesses, and thus the smallest groove areas during scratching, while exhibiting much elastic deformation. Microcracking was observed in scratch grooves of some noncovalent hard phases that could not withstand the stresses underneath the indenter and thus fractured.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Gefüge und abrasiver Verschleiß von Kaltarbeitsstählen mit 12% Cr10.1002/srin.198405340 ↗
2. Einfluss von harten Phasen auf den abrasiven Verschleisswiderstand von Manganhartstahl
3. Brust · 2017
4. Manufacturing of hard composite materials on Fe-base with oxide particles10.4028/www.scientific.net/KEM.742.106 ↗
5. Spherical nanoindentation stress–strain curves10.1016/j.mser.2015.02.001 ↗
6. Fischer-Cripps · 2007
7. Deutsches Institut für Normung e.V., Metallische Werkstoffe - Instrumentierte Eindringprüfung zur Bestimmung der Härte und anderer Werkstoffparameter.
8. Cementite characterization with chromium and vanadium contents using indentation technique10.1016/S1006-706X(15)30013-3 ↗
9. Fracture toughness of carbides in tool steels evaluated by nanoindentation10.1016/j.actamat.2007.03.028 ↗
10. Indentation size effect for the hardness of refractory carbides10.2320/matertrans.M2010110 ↗
11. Development of pile-up during spherical indentation of elastic–plastic solids10.1016/j.ijsolstr.2004.02.033 ↗
12. Elastic deformation, plastic flow, and dislocations in single crystals of titanium carbide10.1063/1.1777197 ↗
13. Review: indentation size effect, indentation cracks and microhardness measurement of brittle crystalline solids - some basic concepts and trends10.1002/crat.200900385 ↗
14. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
15. Röttger · 2011
16. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
17. G. M. Pharr, E. G. Herbert, Y. Gao, The indentation size effect: a critical examination of experimental observations and mechanistic interpretations, Annu. Rev. Mater. Res. 40 (1). doi:10.1146/annurev-matsci-070909-104456.10.1146/annurev-matsci-070909-104456 ↗
18. Deformation at the nanometer and micrometer length scales: effects of strain gradients and dislocation starvation10.1016/j.tsf.2006.01.030 ↗
19. Flow of covalent solids at low temperatures10.1063/1.321567 ↗
20. Dislocation starvation and exhaustion hardening in Mo alloy nanofibers10.1016/j.actamat.2011.12.027 ↗
21. Continuum modeling of dislocation starvation and subsequent nucleation in nano-pillar compressions10.1016/j.scriptamat.2011.10.009 ↗
22. Zum Gahr · 1987 · vol. 10
23. Strain-induced precipitation of NbC in Nb and Nb–Ti microalloyed HSLA steels10.1016/S1359-6462(01)01214-3 ↗
24. Dislocations in ceramics10.1179/mst.1985.1.11.944 ↗
25. Carter · 2007
26. Variable (intrinsic) material length scale for face-centred cubic metals using nano-indentation
27. Briehl · 2014
28. Salmang · 2007
29. Irradiation-induced hardening/softening in SiO2 studied with instrumented indentation10.1016/j.msea.2005.01.060 ↗
30. Hardness of covalent crystals10.1103/PhysRevLett.91.015502 ↗
31. Compressive deformation and fracture in WC materials10.1016/0025-5416(88)90710-0 ↗
32. Chemical and physical mechanisms of dielectric chemical mechanical polishing (CMP)
33. Analysis of scratches formed on oxide surface during chemical mechanical planarization10.1149/1.3265474 ↗
34. Datensammlung zu Hartstoffeigenschaften10.1002/mawe.19970280206 ↗
35. Hardness anisotropy of single crystals of IVa-Diborides10.1143/JJAP.12.186 ↗