journal article·2020-01

Effect of local stresses of primary twinning on double twinning, twin intersection and their competition

C. Xie, M.H. Xiang, Z.E. Zhang, X. Liu, B.W. Zhu, J.B. Chen, X.F. Wang, X.D. Shu, Q.H. Fang

Publisher page

Abstract

Abstract Taking into account the local stresses resulting from the primary twinning with transformation strains, the competition between double twinning {10–11}–{10–12} and (10–12)–(–1012) (CDTW and EDTW) is theoretically modeled. Using electron backscatter diffraction technique, the statistical fractions, thickness-length ratios and their critical values of CDTW and EDTW within grains of as-cast AZ31 magnesium alloy sheets at the low strain stage of hot rolling processing are obtained to validate the theoretical results. In addition, the competition between the DTW and twin intersection are also discussed in detail. The results show that: (1) The secondary twin growth complies with the classical Hall-Petch relationship. Due to the difference in the driving forces resulting from different transformation strains between the primary extension and contraction twinning, the secondary extension twin of EDTW is more difficult to grow compared to that of CDTW for primary twin bands with small thickness-length ratios, which is contrary to the regulation for primary twin bands with large thickness-length ratios; (2) The greater the thickness-length ratio of the primary twinning is, the smaller the critical shear stress of the secondary twinning is. This is opposite to the effect of thickness-length ratio on the critical shear stress of the incident twinning in the twin intersection. It is indicated that the thickening of the primary twinning provides the higher driving force for the formation of DTW, however hinders the twin intersection more evidently; (3) Within coarse grains, at the low strain stage, the formation of DTW can dominantly induce dynamic recrystallization and continue plastic deformation, while the stress concentration resulting from the twin intersection is inclined to cause brittle fracture. Therefore, based on the effect of the local stress, the selection mechanism of the thickness-length ratio on the DTW and twin intersection is of great significance to determining the plastic performance of magnesium alloys during hot working. In the current study, massive control factors of the thickness-length ratio of the primary twinning are concluded, which provides some corresponding schemes of material design.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. On the role of twinning and stacking faults on the crystal plasticity and grain refinement in magnesium alloys10.1016/j.actamat.2017.11.004 ↗
2. Dynamic recrystallization mechanisms during hot compression of Mg-Gd-Nd-Zr alloy10.1016/S1003-6326(15)63789-X ↗
3. Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate10.1016/S1003-6326(14)63145-9 ↗
4. An investigation of dynamic recrystallization behavior of ZK60-Er magnesium alloy10.1016/j.msea.2014.06.058 ↗
5. Softening and dynamic recrystallization in magnesium single crystals during c-axis compression10.1016/j.actamat.2011.10.013 ↗
6. Recrystallization mechanism of as-cast AZ91 magnesium alloy during hot compressive deformation10.1016/j.msea.2009.08.062 ↗
7. Twinning-related microstructural evolution during hot rolling and subsequent annealing of pure magnesium10.1016/j.msea.2009.03.015 ↗
8. Twin recrystallization mechanisms in magnesium-rare earth alloys10.1016/j.actamat.2015.05.044 ↗
9. The role of Al content on deformation behavior and related texture evolution during hot rolling of Mg-Al-Zn alloys10.1016/j.jallcom.2016.10.222 ↗
10. Twinning-induced dynamic recrystallization and micro-plastic mechanism during hot-rolling process of a magnesium alloy10.1016/j.msea.2017.05.037 ↗
11. Dynamic recrystallization in pure magnesium10.2320/matertrans.42.1928 ↗
12. Deformation behavior of AZ31 Mg alloys sheet during large strain hot rolling process: a study on microstructure and texture evolutions of an intermediate-rolled sheet10.1016/j.jallcom.2015.12.063 ↗
13. Strain-rate effects on twinning, dynamic recrystallization and their competition of casting AZ31 Mg alloys during the plane strain compression
14. Transition of dynamic recrystallization mechanisms of as-cast AZ31 Mg alloys during hot compression10.1016/j.ijplas.2018.07.017 ↗
15. Deformation of twins in a magnesium alloy under tension at room temperature10.1016/j.jallcom.2014.01.100 ↗
16. Structural characteristics of {ī012} non-cozone twin-twin interactions in magnesium10.1016/j.actamat.2018.08.004 ↗
17. Sequential {ī012} twinning stimulated by other twins in titanium10.1016/j.actamat.2017.04.023 ↗
18. Theoretical study on the {-1012} deformation twinning and cracking in coarse-grained magnesium alloys10.1016/j.ijplas.2016.02.001 ↗
19. Twin-like domains and fracture in deformed magnesium10.1016/j.scriptamat.2013.06.014 ↗
20. Effect of local stress fields on twin characteristics in HCP metals10.1016/j.actamat.2016.06.042 ↗
21. A study of microstructure-driven strain localizations in two-phase polycrystalline HCP/BCC composites using a multi-scale model10.1016/j.ijplas.2015.06.003 ↗
22. Thermostastitical modelling of deformation twinning in HCP metals10.1016/j.ijplas.2013.09.006 ↗
23. On the nucleation and growth of {112‾2}twin in commercial purity titanium: in situ investigation of the local stress field and dislocation density distribution10.1016/j.actamat.2016.08.073 ↗
24. On the effects of reorientation and shear transfer during twin formation: comparison between high resolution electron backscatter diffraction experiments and a crystal plasticity finite element model10.1016/j.ijplas.2016.05.006 ↗
25. Dislocation mediated variant selection for secondary twinning in compression of pure titanium10.1016/j.actamat.2016.10.063 ↗
26. Role of microstructure on twin nucleation and growth in HCP titanium: a statistical study10.1016/j.actamat.2018.01.041 ↗
27. Yield symmetry and reduced strength differential in Mg-2.5Y alloy10.1016/j.actamat.2016.08.037 ↗
28. Refined microstructure and improved mechanical properties of high-ratio extruded AZ91-xSn magnesium alloy10.1016/j.matchemphys.2015.06.052 ↗
29. Modeling of twin formation, propagation and growth in a Mg single crystal based on crystal plasticity finite element method10.1016/j.ijplas.2016.08.002 ↗
30. Numericl analysis of twin thickening process in magnesium alloys10.1016/j.actamat.2016.10.068 ↗
31. Effect of particles on the formation of deformation twins in a magnesium-based alloy10.1016/j.msea.2009.04.001 ↗
32. The effect of internal stresses due to precipitates on twin growth in magnesium10.1016/j.actamat.2016.09.022 ↗
33. Precipitation and hardening in magnesium alloys10.1007/s11661-012-1217-2 ↗
34. Effects of loading conditions on twin characteristics in an extruded Mg-Zr alloy10.1016/j.msea.2018.03.095 ↗