Microstructure and mechanical properties of friction stir processed cast Eglin steel (ES-1)
Source abstract
Abstract
Abstract Eglin steel, an ultra-high-strength steel developed for various demanding applications, is a low-cost alternative to 4340 steel, in which nickel and cobalt additions are replaced by higher tungsten additions, thereby achieving comparable strength and ductility. Friction stir processing (FSP) was carried out on this steel under two heat input conditions, which fell above the A 3 transformation line. Microhardness values along the horizontal and vertical directions of the processed region cross section were reported for the lower heat input condition, and correlated with corresponding microstructures. A 3D heat transfer and material flow model was used to predict the peak temperature and cooling rates in these zones. Site-specific tensile tests of specimens extracted from the top to the bottom of the stir zone (SZ) showed ultimate tensile strength (UTS) greater than 2 GPa, with a total elongation close to 10% at ~ 4 mm from the top surface of SZ. Transmission electron microscopy (TEM) analysis of the high strength location showed microstructure consisting of nano-twinned martensite and nano-bainite laths of size ranging from 200 nm to 300 nm, and confirmed the existence of retained austenite. This mixed microstructure was comprised of finer aggregates of martensite, bainite and retained austenite, which were postulated to be responsible for the high strength and ductility combinations.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. J.R. Paules, M.F. Dilmore, K.J. Handerhan, Development of Eglin Steel – A New, Ultrahigh-strength Steel for Armament and Aerospace Applications. Materials Science and Technology-association for Iron and Steel Technology, 2, 2005, pp. 13–23.
2. Dilmore Morris, James D. Ruhlman, Eglin Steel – A Low Alloy High Strength Composition, U.S. Patent No. 7,537,727, 26 May 2009.
3. Friction stir welding and processing10.1016/j.mser.2005.07.001 ↗
4. Properties of friction-stir-welded 7075 T651 aluminum10.1007/s11661-998-0021-5 ↗
5. Basal plane texture and flow pattern in friction stir weld of a magnesium alloy10.1007/s11661-003-0228-4 ↗
6. Corrosion resistance of friction stir welded 304 stainless steel10.1016/j.scriptamat.2004.04.001 ↗
7. Microstructural modification of as-cast NiAl bronze by friction stir processing10.1007/s11661-004-0242-1 ↗
8. R.S. Mishra, P.S. De, N. Kumar, Friction Stir Welding of High Temperature Alloys, 2014, pp. 189–235.10.1007/978-3-319-07043-8_7 ↗
9. Friction stir welding of carbon steels10.1016/j.msea.2006.04.118 ↗
10. Friction stir welding of a high carbon steel10.1016/j.scriptamat.2006.12.004 ↗
11. Transformation in stir zone of friction stir welded carbon steels with different carbon contents10.2355/isijinternational.47.299 ↗
12. Friction stir welding studies on mild steel
13. Friction Stir Welding of DH36 Steel10.1179/136217103225009125 ↗
14. A Microstructural study of friction stir welded joints of carbon steels
15. Microstructural characterisation of stir zone containing residual ferrite in friction stir welded 304 austenitic stainless steel10.1179/174329305X46691 ↗
16. Microstructure and mechanical properties of friction stir welded SAF 2507 super duplex stainless steel10.1016/j.msea.2005.02.054 ↗
17. Recrystallization in type 304L stainless steel during friction stirring10.1016/j.actamat.2004.10.017 ↗
18. The joint properties of brass plates by friction stir welding10.1016/j.matdes.2005.05.006 ↗
19. Friction stir lap welded advanced high strength steels: microstructure and mechanical properties10.1016/j.msea.2011.06.087 ↗
20. Effect of friction stir welding conditions on properties and microstructures of high strength automotive steel10.1179/136217108X388633 ↗
21. Empirical formulae for the calculation of some transformation temperatures
22. Numerical simulation of three-dimensional heat transfer and plastic flow during friction stir welding10.1007/s11661-006-1076-9 ↗
23. Three-dimensional heat and material flow during friction stir welding of mild steel10.1016/j.actamat.2006.09.009 ↗
24. Tool geometry for friction stir welding – optimum shoulder diameter10.1007/s11661-011-0672-5 ↗
25. Torque, power requirement and stir zone geometry in friction stir welding through modeling and experiments10.1016/j.scriptamat.2008.08.015 ↗
26. Strains and strain rates during friction stir welding10.1016/j.scriptamat.2009.07.015 ↗
27. Patankar · 1980 · 210 · 1980
28. Modeling of heat transfer and fluid flow during gas tungsten arc spot welding of low carbon steel10.1063/1.1540744 ↗
29. Reliable calculations of heat and fluid flow during conduction mode laser welding through optimization of uncertain parameters
30. A heat-transfer and fluid-flow-based model to obtain a specific weld geometry using various combinations of welding variables10.1063/1.2001153 ↗
31. Modeling of ferrite formation in a duplex stainless steel weld considering non-uniform starting microstructure10.1016/j.actamat.2005.05.040 ↗
32. Integrated modelling of thermal cycles, austenite formation, grain growth and decomposition in the heat affected zone of carbon steel
33. Composition change of stainless steel during microjoining with short laser pulse10.1063/1.1785868 ↗
34. Numerical prediction of fluid flow and heat transfer in welding with a moving heat source10.1080/10407789608913782 ↗
35. Mechanical properties and microstructural evolution of simulated heat-affected zones in wrought Eglin steel10.1007/s11661-015-3131-x ↗
36. Mechanical properties and retained austenite in intercritically heat-treated bainite-transformed steel and their variation with Si and Mn additions10.1007/BF02656816 ↗
37. Models for the Elementary Mechanical Properties of Steel Welds
38. Grain structure and dislocation density measurements in a friction-stir welded aluminum alloy using X-ray peak profile analysis10.1016/j.msea.2008.08.007 ↗
39. X-ray and neutron diffraction measurements of dislocation density and subgrain size in a friction-stir-welded aluminum alloy10.1007/s11661-009-9963-5 ↗
40. Enhanced tensile properties of Fe–Ni–C steel resulting from stabilization of austenite by friction stir welding10.1016/j.jmatprotec.2014.09.014 ↗