Inconsistent flow stress in low carbon boron steels during finishing
Source abstract
Abstract
Abstract The influence of deformation parameters and composition on flow stress behaviour of boron-containing steels is described. High boron steels displayed a consistent flow stress during finishing due to the boron concentration at austenite grain boundaries having achieved steady state followed by the precipitation of BN. Higher flow stresses than those found in boron-free steel were due to solute boron at grain boundaries, which delayed the onset and the rate of dynamic recrystallisation (DRX) and consequently enhanced the solute drag effect. In low B steels, inconsistent flow stress behaviour at finishing temperatures above the BN solubility temperature was attributed to deformation at or near the maximum non-equilibrium grain boundary segregation (NGS) of boron, which occurred rapidly. The flow stress in low B steels was consistent when DRX occurred during roughing and early finishing and was promoted by weak NGS and a finer grain size when the reheat temperature was decreased. Flow stress consistency was also promoted by avoiding a NGS peak by deforming at temperatures below the BN solubility temperature. A high driving force for AlN precipitation in austenite increased flow stress inconsistency through the protection of solute boron for NGS and increased solute drag.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnetic Properties and Applications · Microstructure and Mechanical Properties of Steels · Metallurgical Processes and Thermodynamics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Samuel · ISIJ Int. · 1989 · 29 · 87810.2355/isijinternational.29.878 ↗
2. Dumitrescu · Metall. New Mater. Res. · 2002 · X · 35
3. Hondors · Int. Mater. Rev. · 1977 · 22 · 26210.1179/imr.1977.22.1.262 ↗
4. Watanabe · Trans. ISIJ · 1983 · 23 · 3110.2355/isijinternational1966.23.31 ↗
5. W. Stumpf, K.M. Banks, Mater. Sci. Eng. A, University of Pretoria, submitted for publication.
6. He · Acta Metall. · 1989 · 37 · 290510.1016/0001-6160(89)90325-8 ↗
7. Shen · 1993 · 323
8. T. Mavropooulos, J.J. Jonas, G.E. Ruddle, Proceedings of the International Conference On HSLA Steels 1985, Beijing, China; in: J.M. Gray et al. (Ed.), HSLA Steels: Metallurgy and Applications, ASM, Ohio, 1986.
9. Stumpf · J. S. Afr. Inst. Min. Metall. · 2003 · 103 · 617
10. Gladman · 1997
11. Fountain · Trans. AIME · 1962 · 230 · 599
12. Leslie · Trans. ASM · 1954 · 46 · 1470
13. Wilson · Int. Mater. Rev. · 1988 · 33 · 22110.1179/imr.1988.33.1.221 ↗
14. Stumpf · J. S. Afr. Inst. Min. Metall. · 2004 · 104 · 643
15. Tingdong · Prog. Mater. Sci. · 2004 · 49 · 10910.1016/S0079-6425(03)00019-7 ↗
16. Taylor · Metall. Trans. · 1990 · 21A · 1679
17. Zhang · Mater. Sci. Technol. · 2000 · 16 · 30510.1179/026708300101507866 ↗
18. Tingdong · Acta Metall. · 1989 · 37 · 249910.1016/0001-6160(89)90048-5 ↗
19. Busby · J. Metall. · 1953 · 5 · 1463
20. Shenhua · J. Mater. Sci. · 1994 · 29 · 6110.1007/BF00356573 ↗
21. Wang · ISIJ Int. · 2002 · 42 · S3810.2355/isijinternational.42.Suppl_S38 ↗
22. Messien · Steel Res. · 1989 · 60 · 32010.1002/srin.198901660 ↗
23. Bai · ISIJ Int. · 1996 · 36 · 108410.2355/isijinternational.36.1084 ↗
24. Djahazi · Mater. Sci. Technol. · 1992 · 8 · 62810.1179/mst.1992.8.7.628 ↗
25. Takahashi · 1982 · 133
26. Engl · 1985 · 123