journal article·2002-06

Role of lamellar plates in creep of TiAl alloy with fully lamellar structure

T Matsuo, T Nozaki, T Asai, M Takeyama

Publisher page

Abstract

Abstract The role of lamellar plates in near γ Ti–48 at.% Al alloy with fully transformed lamellar structure was investigated by studying the difference in creep rate–time curve between Ti–48 at.% Al alloy and the γ single phase Ti–50 at.% Al alloy. Creep tests were conducted at 1123 K under a low stress of 68.6 MPa. The superiority of FL specimen is derived not from decreasing the creep rate, but from retarding the onset of accelerating creep. The absence of dynamic recrystallization along grain boundaries is interpreted as causing retardation of accelerating creep. The α 2 lamellar plates have a more drastic effect on suppressing dynamic recrystallization than the γ lamellar plates. Dynamic recrystallization would be fully suppressed in a Ti–Al PST crystal, because of the absence of grain boundaries. By conducting the creep tests of PST crystals with different lamellar orientations to stress axis, φ , φ dependence of creep rate was investigated. In the specimens with φ from 30 to 70°, creep rate is larger than that in polycrystalline FL specimen. For the specimen with φ less than 30° and larger than 80°, the creep rate becomes smaller than that of the FL specimen, and in the case of the specimens with φ near 0 or 90° a marked decrease in creep rate is confirmed. The correlation between interlamellar spacing and creep rate is investigated using FL specimen with four different interlamellar spacing. Decreasing the interlamellar spacing gives a short transient stage and a short accelerating stage.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. M. McLean, R.N. Ghosh, R.V. Curtis, U. Basu-Conlin, M.R. Winstone. In: S.D. Antolovich et al. (Ed.), Proceedings of the Seventh International Conference on Superalloys, TMS, Warrendale, 1992, p. 609.10.7449/1992/Superalloys_1992_609_618 ↗
2. Evans · Mater. Sci. Tech. · 1987 · 3 · 70110.1179/mst.1987.3.9.701 ↗
3. T. Matsuo, S. Takahashi, Y. Ishiwari, Y. Terada, Proceedings of the Eighth International Conference on Creep and Fracture of Engineering Materials and Structures, 1999, p. 553.10.4028/www.scientific.net/KEM.171-174.553 ↗
4. Final Report of Research Group Strengthening of Heat resisting steel and Alloy, ISIJ, 2000, p. 174.
5. M. Koo, Doctor of Engineering Thesis, Tokyo Institute of Technology, 1992.
6. K. Nakajima, Doctor of Engineering Thesis, Tokyo Institute of Technology, 1992.
7. M. Koo, T. Matsuo, M. Kikuchi, Proceedings of the International Conference Intermetallic Compounds, JIMIS-6, 1991, p. 519.
8. T. Matsuo, O. Takahashi, M. Takeyama, Proceedings of the International Conference on Thermomechanical Processing of Steels & Other Materials, 1997, p. 1465.
9. Terada · Proc. Intern. Cont. Stainless Steel Stainless Steel · 1991 · 91 · 618
10. T. Matsuo, M. Kikuchi, T. Watanabe, Y. Monma, Proceedings of the Fifth International Conference on Creep of Materials, 1992, p. 618.
11. A.K. Mukherjee, J.E. Bird, J.E. Dorn, Trans. ASM 62 (1969) 155.
12. Y. Terada, Doctor of Engineering Thesis, Tokyo Institute of Technology, 1993.
13. Y. Terada, T. Matsuo, M. Kikuchi, Proceedings of the Seventh JIM International Symposium, JIMIS7, 1993, p. 27.
14. T. Nozaki, K. Araki, M. Takeyama, T. Matsuo, Proceedings of the International. Cont. Thermomechanical Processing of Steel and Other Material, 1997, p. 1415.
15. Matsuo · Intermetallics · 1998 · 6 · 69510.1016/S0966-9795(98)00046-6 ↗
16. N. Shiratori, S. Hirata, T. Asai, M. Takeyama, T. Matsuo, Proceedings of the International Cont. Creep and Fracture of Engineering Materials and Structures, 1999, p. 639.10.4028/www.scientific.net/KEM.171-174.639 ↗
17. T. Fujiyama, A. Nakamura, M. Hosomi, S.R. Nishitani, M. Yamaguchi, Phil. Mag., 1990, p. 591.10.1080/01418619008231937 ↗
18. Y.W. Kim, Microstructure/Property Relationship in Titanium Aluminides and Alloys, TMS, 1991, p. 91.
19. R. Yamamoto, K. Mizoguchi, Fracture of Engineering Materials and Structures, 1999, p. 717.10.4028/www.scientific.net/KEM.171-174.717 ↗