journal article·2008-02

Microstructural and mechanical characterization of iron samples sintered in DC plasma

H.C. Pavanati, G. Straffelini, A.M. Maliska, A.N. Klein

Materials Science and Engineering: A· Volume 474· Issue 1-2
Publisher page

Abstract

Abstract Samples of unalloyed iron were sintered in an abnormal glow discharge using a confined anode–cathode configuration. In this geometry the samples were placed on the holder, which acted as the discharge anode, while the cathode surrounded the sample undergoing bombardment by ions and energetic neutral atoms/molecules, leading to heating and sputtering. For comparison, another set of samples was sintered in a resistive furnace. The presence of large grains was observed for plasma-sintered unalloyed iron, which could be attributed to a large amount of atomic hydrogen in the electric discharge. These grains influence the mechanical properties of the sintered product. Three-point bending tests revealed lower yield strength and, quite surprisingly, ductility, compared to samples sintered in a furnace under the same temperature and time conditions. The decrease in ductility is associated with intergranular crack propagation in plasma-sintered samples. Such embrittlement could be attributed to the absorption of hydrogen during plasma sintering or higher impurity content at grain boundaries.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Plasma Diagnostics and Applications · Electrostatic Discharge in Electronics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Batista · Int. J. Powder Metall. · 1998 · 34 · 55
2. I.T. Lawall, Ph.D. Thesis, Universidade Federal de Santa Catarina, Florianópolis, Brazil, 2001.
3. Lourenço · Mater. Res. · 2004 · 7 · 26910.1590/S1516-14392004000200009 ↗
4. Maliska · Mater. Sci. Eng. A · 2003 · 352 · 27310.1016/S0921-5093(02)00914-0 ↗
5. S.F. Brunatto, Ph.D. Thesis, Universidade Federal de Santa Catarina, Florianópolis, Brazil 2000.
6. Chapman · 1980
7. Von Engel · 1994
8. Lourenço · 2003
9. Pavanati · Mater. Sci. Eng. A · 2005 · 392 · 31310.1016/j.msea.2004.09.034 ↗
10. ASTM Standard E112-96E1, Standard test methods for determining average grain size.
11. Huppmann · 1986
12. German · 1996
13. Budtz-Jorgensen · Surf. Coat. Technol. · 2001 · 137 · 10410.1016/S0257-8972(00)01090-2 ↗
14. Pavanati · Mater. Res. · 2007 · 10 · 8710.1590/S1516-14392007000100019 ↗
15. J.M. Lourenço, Ph.D. Thesis, Universidade Federal de Santa Catarina, Florianópolis, Brazil, 2004.
16. Reed-Hill · 1992
17. Grabke · Steel Res. · 1986 · 57 · 17810.1002/srin.198600750 ↗
18. Tamura · 1988
19. Straffelini · Mater. Sci. Eng. A · 1998 · 248 · 15310.1016/S0921-5093(98)00496-1 ↗
20. Brooks · 1993
21. Bogaerts · Spectrochim. Acta Part B · 2002 · 107110.1016/S0584-8547(02)00047-2 ↗
22. Belkind · Surf. Coat. Technol. · 1995 · 76–77 · 73810.1016/02578-9729(50)25057- ↗
23. Santos · Mater. Sci. Eng. A · 2005 · 407 · 7110.1016/j.msea.2005.06.026 ↗
24. Gale · 2004