Indentation size effects in pack carbo-nitrided AISI 8620 steels
Source abstract
Abstract
Abstract This paper explores the indentation size effect (ISE) in pack carbo-nitrided AISI 8620 steel surfaces. The surfaces of the AISI 8620 steel samples were pack carbo-nitrided at 900 °C using cyanide-containing dried cassava leaves (bio-processed waste). This was achieved by quenching in different pH levels of cyanide-based bio-processed solution (BPS). Nanoindentation was carried out (using a Berkovich tip) on the surface modified steels. This was used to measure the hardness and reduced elastic moduli of the quenched-carbonitrided and the as-received steel surfaces. The surface-modified steel was shown to have higher hardness than the as-received steel. The hardness was also found to depend strongly on the indentation size. The paper also considers the potential contributions from microstructure, geometrically necessary dislocations (GNDs) and C/N diffusion on the measured hardness values. However, the measured ISEs are attributed largely to the role of GNDs that are modeled using the Nix and Gao mechanism-based strain gradient plasticity model. The implications of the results are then discussed for the design of hard carbo-nitrided steel surfaces.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (44)
Show source-provided references
1. Tijani · 2008
2. A novel method of surface modification for steel by plasma electrolysis carbonitriding10.1016/j.msea.2006.12.067 ↗
3. An evaluation of possibilities of the carbonitride simple steels instead of carburized low alloy steels (wear properties)10.1016/S0169-4332(97)00173-6 ↗
4. Development of an environmentally friendly in-situ pack-cyaniding technique
5. Case-depth studies of pack cyaniding of mild steel using cassava leaves10.1081/AMP-200030626 ↗
6. Metallographic studies of pack cyanided mild steel using cassava leaves10.1080/10426910801938551 ↗
7. A reformulation of strain gradient plasticity10.1016/S0022-5096(01)00049-7 ↗
8. Indentation-size effect in single-crystal MgO10.1080/01418610208235721 ↗
9. Relationship between indentation size effect and material properties in microhardness measurement of some cobalt-based alloys10.1016/S0254-0584(02)00546-1 ↗
10. Effect of the indenter size on the indentation of aluminum10.1016/j.matchar.2006.02.012 ↗
11. Finite element simulation of nano-indentation experiment on aluminum 110010.1016/j.commatsci.2013.09.019 ↗
12. Depth dependence of hardness in copper single crystals measured by nanoindentation10.1016/S1359-6462(00)00598-4 ↗
13. Naonindentation measurements of the mechanical properties of polycrystalline Au and Ag thin films on silicon substrates: effects of grain size and film thickness10.1016/j.msea.2006.04.080 ↗
14. Size dependent hardness of silver single crystals10.1557/JMR.1995.0853 ↗
15. Surface effects and the size-dependent hardening and strengthening of nickel micropillars10.1016/j.jmps.2012.04.009 ↗
16. Experimental and numerical study on geometrically necessary dislocations and non-homogeneous mechanical properties of the ferrite phase in dual phase steels10.1016/j.actamat.2011.03.062 ↗
17. Separation of size-dependent strengthening contributions in fine-grained dual phase steels by nanoindentation10.1016/j.actamat.2006.03.031 ↗
18. Indentation size effect on the Fe2B/Substrate interface10.1016/j.surfcoat.2011.07.029 ↗
19. Indentation Size Effect (ISE) of Vickers hardness in steels: correlation with H/E10.4028/www.scientific.net/AMM.391.23 ↗
20. Analysis of indentation size effect of Vickers hardness tests of steels10.4028/www.scientific.net/AMR.652-654.1307 ↗
21. Analytical and experimental determination of the material intrinsic length scale of strain gradient plasticity theory from micro- and nano-indentation experiments10.1016/j.ijplas.2003.10.007 ↗
22. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
23. Indentation size effects in face centered cubic single crystal thin films10.1016/j.msea.2005.05.075 ↗
24. Indentation size effects in the nano and microhardness of fcc single crystal metals10.1080/10426910601063410 ↗
25. Correlation between nanoindentation and tensile properties influence of indentation size effect10.1016/S0921-5093(03)00563-X ↗
26. Indentation size effect in Ni–Fe solid solutions10.1016/j.actamat.2007.08.044 ↗
27. An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
28. Nanoindentation and the indentation size effect: kinetics of deformation and strain gradient plasticity10.1016/S0022-5096(02)00033-9 ↗
29. Boyer · 1998
30. T.V. Rajan, C.P. Sharma, A. Sharma, Heat treatment: principles and techniques, in: C.V. Sundaram (Ed.), PHI Learning Pvt. Ltd., Metals, 2012.
31. Mechanical properties of mild steel rod in Cassava Fluid
32. Finite element simulation of the effect of surface roughness on nanoindentation of thin films with spherical indenters10.1016/j.surfcoat.2007.07.038 ↗
33. A review of analysis methods for sub-micron indentation testing10.1016/S0042-207X(00)00377-8 ↗
34. Determination of strain gradient plasticity length scale for micro-electronics solder alloys10.1115/1.2721082 ↗
35. Cassava leaves as packaging materials
36. Comparative study of some varieties of cassava grown and consumed in bayelsa state as prospective biofuel and energy food sources
37. Simulation of case depth of cementation steels according to Fick’s Laws10.1016/S1006-706X(13)60023-0 ↗
38. Indentation size effect in polycrystalline fcc metals10.1016/S1359-6454(02)00175-1 ↗
39. Indentation size effect in metallic materials: correcting for the size of the plastic zone10.1016/j.scriptamat.2005.02.009 ↗
40. The double effect of grain size on the work-hardening behavior of polycrystalline copper10.1016/0956-716X(94)90024-8 ↗
41. Strain gradient interpretation of size effects10.1023/A:1018625006804 ↗
42. Microstructure versus size: mechanical properties of electroplated single crystalline Cu nanopillars10.1103/PhysRevLett.104.135503 ↗
43. Effects of focused ion beam milling on the nanomechanical behavior of a molybdenum-alloy single crystal10.1063/1.2784948 ↗
44. FIB damage of Cu and possible consequences for miniaturized mechanical tests10.1016/j.msea.2007.01.046 ↗