Precipitation reactions in 12Cr–3Ni–3Mn–3Cu–0.15Nb steel
Source abstract
Abstract
Abstract In the current study, a new precipitation hardenable stainless steel was designed with primarily Ni and Mn modification using Thermo-Calc. The solution-annealing heat treatment at 1035 °C for 60 min followed by air quenching resulted in a fully martensitic microstructure. The as-quenched steel responded to the aging heat treatment, resulting in a significant enhancement of hardness and mechanical strength. The aging heat treatment at 500 °C for 120 min provided a good combination of tensile properties. The change in mechanical properties was quite conducive to the aging parameters (i.e., temperature and time) between 400 °C and 600 °C. Transmission electron microscopy and atom probe tomography studies demonstrated that the evolution of Cu-precipitate was the prime reason for the change in hardness and mechanical properties of as-quenched steel. As a result, the newly developed PH-1 steel was comparable to a commercial Cu-precipitate strengthened 17-4 PH steel in terms of mechanical properties. The Cu-precipitate evolved with a concurrent increase of Cu and decrease of Fe contents. APT studies revealed the interfacial segregation of Ni and Mn at the matrix and the Cu-rich precipitate in a peak-aged condition, which evolved as Ni–Mn rich reverse austenite upon over-aging, accompanied by high Mn:Si ratio. Cu precipitate only acted as a heterogeneous nucleation site for reverse austenite formation as there was no Cu atoms partition.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Advanced Materials Characterization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (77)
Show source-provided references
1. Effects of aging on the microstructure of 17-4 PH stainless steel10.1016/0025-5416(88)90420-X ↗
2. TEM investigation of precipitation phenomena occurring in PH 15-5 alloy10.1016/0956-7151(93)90270-3 ↗
3. High-resolution electron microscopy analysis of the structure of copper precipitates in a martensitic stainless steel of type PH 15-510.1080/095008396180786 ↗
4. Evolution of the microstructure of a 15-5PH martensitic stainless steel during precipitation hardening heat treatment10.1016/j.matdes.2016.06.068 ↗
5. Sequential nucleation of phases in a 17-4PH steel: microstructural characterisation and mechanical properties10.1016/j.actamat.2016.11.052 ↗
6. Nano-precipitates evolution and their effects on mechanical properties of 17-4 precipitation-hardening stainless steel10.1016/j.actamat.2018.06.031 ↗
7. Quantitative electron microscopy and physically based modelling of Cu precipitation in precipitation-hardening martensitic stainless steel 15-5 PH10.1016/j.matdes.2018.01.049 ↗
8. The interaction between ε-copper and dislocation in a high copper 17-4PH steel10.1016/j.msea.2019.03.092 ↗
9. Precipitation hardening in a PH 13-8 Mo stainless steel10.1016/0025-5416(81)90034-3 ↗
10. Microstructural evolution in a PH13-8 stainless steel after ageing10.1016/S1359-6454(02)00353-1 ↗
11. Microstructural evolution in 13Cr–8Ni–2.5 Mo–2Al martensitic precipitation-hardened stainless steel10.1016/j.msea.2004.12.002 ↗
12. Precipitation evolution in a Ti-free and Ti-containing stainless maraging steel10.1016/j.ultramic.2008.10.016 ↗
13. Splitting phenomenon in the precipitation evolution in an Fe–Ni–Al–Ti–Cr stainless steel10.1016/j.actamat.2009.10.030 ↗
14. Strengthening behavior of Fe–Cr–Ni–Al–(ti) maraging steels10.1016/j.msea.2011.03.058 ↗
15. Cao · 2011
16. Charles · 1949
17. Clarke · 1971
18. Clarke · 1971
19. Clarke · 1958
20. Hultin-Stigenberg · 1999
21. Hultin-Stigenberg · 1997
22. Liu · 1992
23. Myers · 1977
24. Myers · 1968
25. Myers · 1971
26. Schumacher · 1992
27. Short · 2004
28. Stigenberg · 1996
29. Wright · 2011
30. Wyche · 1945
31. Davis · 2000
32. Balachandran · 2013 · 135
33. Calculation of the effect of alloying elements on the Ms temperature in steels10.1016/0925-8388(94)06002-9 ↗
34. Study of the influence of alloying elements on Cu precipitation in steel by non-classical nucleation theory10.1016/j.actamat.2006.05.006 ↗
35. Transmission electron microscope investigations of the structure of copper precipitates in thermally-aged Fe—Cu and Fe—Cu—Ni10.1080/09500839108215121 ↗
36. High-resolution electron microscopy studies of the structure of Cu precipitates in α-Fe10.1080/01418619408242533 ↗
37. Atomic structure of the Cu precipitates in two stages hardening in maraging steel10.1016/j.matlet.2004.09.058 ↗
38. Phase transformation of Cu precipitates from bcc to fcc in Fe–3Si–2Cu alloy10.1016/j.actamat.2012.09.068 ↗
39. Phase transformation of Cu‐rich precipitates from 9R to 3R variant via ledges mechanism in ferritic steel containing copper10.1111/jmi.12352 ↗
40. Evolution of crystal structure of Cu precipitates in a low carbon steel10.1016/j.matdes.2017.08.054 ↗
41. Direct observations on the crystal structure evolution of nano Cu-precipitates in an extremely low carbon steel10.1016/j.matlet.2016.10.077 ↗
42. Aging reactions in a 17-4 PH stainless steel10.1016/S0254-0584(01)00460-6 ↗
43. The effect of ageing upon the microstructure and mechanical properties of type 15-5 PH stainless steel10.1016/S0921-5093(02)00062-X ↗
44. Synergistic effects of Cu and Ni on nanoscale precipitation and mechanical properties of high-strength steels10.1016/j.actamat.2013.06.040 ↗
45. Synergistic alloying effect on microstructural evolution and mechanical properties of Cu precipitation-strengthened ferritic alloys10.1016/j.actamat.2013.09.011 ↗
46. Group precipitation and age hardening of nanostructured Fe-based alloys with ultra-high strengths10.1038/srep21364 ↗
47. Precipitation mechanism and mechanical properties of an ultra-high strength steel hardened by nanoscale NiAl and Cu particles10.1016/j.actamat.2015.06.063 ↗
48. Microstructure characterization of Cu-rich nanoprecipitates in a Fe–2.5 Cu–1.5 Mn–4.0 Ni–1.0 Al multicomponent ferritic alloy10.1016/j.actamat.2012.12.034 ↗
49. Effect of Ni and Mn on the formation of Cu precipitates in α-Fe10.1016/j.scriptamat.2015.01.016 ↗
50. Simulation of bcc-Cu precipitation in ternary Fe-Cu-M alloys10.1016/j.commatsci.2017.09.023 ↗
51. Microstructural evolution in a 17-4 PH stainless steel after aging at 400 C10.1007/s11661-999-0323-2 ↗
52. The effect of microstructural evolution on hardening behavior of type 17-4PH stainless steel in long-term aging at 350 C10.1016/j.matchar.2006.02.004 ↗
53. Precipitation in 9Ni–12Cr–2Cu maraging steels10.1016/S1359-6454(98)00267-5 ↗
54. Effect of Cu on the evolution of precipitation in an Fe–Cr–Ni–Al–Ti maraging steel10.1016/j.actamat.2010.03.010 ↗
55. Monte Carlo simulations of Cu/Ni-Si-Mn Co-precipitation in duplex stainless steels10.1016/j.actamat.2020.03.053 ↗
56. Precipitation-site competition in duplex stainless steels: Cu clusters vs spinodal decomposition interfaces as nucleation sites during thermal aging10.1016/j.actamat.2020.05.017 ↗
57. Pickering · 1978
58. On the role of Ni in Cu precipitation in multicomponent steels10.1007/s11661-013-1933-2 ↗
59. Ageing behaviour of an Fe–20Ni–1.8 Mn–1.6 Ti–0.59 Al (wt%) maraging alloy: clustering, precipitation and hardening10.1016/j.actamat.2004.08.018 ↗
60. Observation of precipitation evolution in Fe-Ni-Mn-Ti-Al maraging steel by atom probe tomography10.1007/s11661-009-9993-z ↗
61. Effects of Mn partitioning on nanoscale precipitation and mechanical properties of ferritic steels strengthened by NiAl nanoparticles10.1016/j.actamat.2014.10.065 ↗
62. A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and plain carbon steels10.1016/0001-6160(59)90170-1 ↗
63. Bhadeshia · 2017
64. LeMay · 1986
65. 2013
66. Cullity · 1956
67. Effect of carbon on the volume fractions and lattice parameters of retained austenite and martensite
68. The distribution of intervariant crystallographic planes in a lath martensite using five macroscopic parameters10.1016/j.actamat.2013.10.010 ↗
69. Applications of atom-probe tomography to the characterisation of solute behaviours10.1016/j.mser.2010.05.001 ↗
70. Atom probe tomographic characterization of nanoscale Cu-rich precipitates in 17-4 precipitate hardened stainless steel tempered at different temperatures10.1017/S1431927616012629 ↗
71. In-situ analysis of redistribution of carbon and nitrogen during tempering of low interstitial martensitic stainless steel10.1016/j.scriptamat.2018.06.004 ↗
72. Co-segregation of boron and carbon atoms at dislocations in steel10.1016/j.jallcom.2017.07.096 ↗
73. A high-resolution electron microscopy study of copper precipitation in Fe-1.5 wt% Cu under electron irradiation10.1080/09500839508241015 ↗
74. Atom probe tomography investigation of lath boundary segregation and precipitation in a maraging stainless steel10.1016/j.ultramic.2012.10.014 ↗
75. The influence of Cu addition on precipitation in Fe–Cr–Ni–Al–(Cu) model alloys10.1016/j.ultramic.2008.11.006 ↗
76. Orientation of austenite reverted from martensite in Fe-2Mn-1.5 Si-0.3 C alloy10.1016/j.actamat.2017.11.003 ↗
77. Growth mode of austenite during reversion from martensite in Fe-2Mn-1.5 Si-0.3 C alloy: a transition in kinetics and morphology10.1016/j.actamat.2018.05.035 ↗