journal article·2019-06

Mechanical properties of cold-rolled metastable Cr–Mn–Ni–N austenitic stainless steel at low ambient temperature

Yichong Zhang, Moucheng Li, Hongyun Bi, Dexiang Chen, Jiaqing Gu, E. Chang

Publisher page

Abstract

Abstract A Cr–Mn–Ni–N series high strength metastable austenitic stainless steel (14Cr10Mn) was used to investigate the effect of cold rolling reduction on mechanical properties at various low testing temperatures. Microstructures of tested samples were observed by transmission electron microscope (TEM) and electron back scatter diffraction (EBSD) at the gauge section. The experimental results show that the size of the rib-like α′- martensite formed during tensile testing is sensitive to temperature but insensitive to cold rolling reduction. The results also show that tensile strength is more sensitive to temperature than yield strength, while the effect of cold rolling is completely opposite. The cold rolling inhibits the martensite transformation kinetics of the tensile process after promoting it at a certain temperature condition, and the promotion effect reaches a maximum value approximately 4% when the cold rolling reduction is 10%. However, it also suppresses the α′- martensite content finally formed during tensile testing due to the high stress-strain state when the cold rolling reduction exceeds 10%, while a larger cold reduction promotes the production of α′- martensite. In addition, lowering temperature can effectively promote the formation of e-martensite at the end of the Stage I of work hardening, and becomes a transitional phase of subsequent transformation to α′- martensite, which directly leads to the enhancement of strength in the stage II of work hardening.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (43)

Show source-provided references
1. The new 200-series: an alternative answer to Ni surcharge? Risks or opportunities?10.1051/metal:2007120 ↗
2. Application of cost-effective stainless steel for automotive components10.1080/10426910903179989 ↗
3. Nitrogen-Alloyed, metastable Austenitic stainless steel for automotive structural applications10.1081/AMP-120027498 ↗
4. The influence of martensitic transformation on mechanical properties of cast high alloyed CrMnNi-steel under various strain rates and temperatures10.1088/1742-6596/240/1/012098 ↗
5. Acoustic emission from ageing-induced martensite formation in cold worked AISI type 304 stainless steel10.1016/0956-716X(94)90379-4 ↗
6. Effect of strain-induced martensite on the formation of nanocrystalline 316L stainless steel after cold rolling and annealing10.1016/j.msea.2009.04.038 ↗
7. Deformation-induced martensitic transformation behavior in cold-rolled AISI304 stainless steels10.1080/10426914.2012.667897 ↗
8. Influence of the cold working induced martensite on the electrochemical behavior of AISI 304 stainless steel surfaces10.1016/j.jmrt.2018.10.004 ↗
9. The effect of cold work on structure and properties of AISI 304 stainless steel10.1016/j.jmatprotec.2007.09.080 ↗
10. Effect of cold rolling on microstructure and mechanical properties of AISI 301LN metastable Austenitic stainless steels10.1016/S1006-706X(12)60153-8 ↗
11. Challa · Scripta Mater. · 2014 · 86 · 6010.1016/j.scriptamat.2014.05.010 ↗
12. Correlation of defect density with texture evolution during cold rolling of a Twinning-Induced Plasticity (TWIP) steel10.1016/j.msea.2017.11.009 ↗
13. On the stress dependence of partial dislocation separation and deformation microstructure in austenitic stainless steels10.1016/S1359-6454(03)00117-4 ↗
14. Tailoring mechanical behavior of a fine-grained metastable austenitic stainless steel by pre-straining10.1016/j.msea.2019.01.038 ↗
15. Effect of low-temperature on mechanical behavior for an AISI 304 austenitic stainless steel10.1016/j.msea.2017.11.003 ↗
16. Deformation-induced phase transformation and strain hardening in type 304 austenitic stainless steel10.1007/s11661-006-0130-y ↗
17. Effect of reverse austenitic transformation on mechanical property and associated texture evolution in AISI 316 austenitic stainless steel processed by low temperature rolling and annealing10.1016/j.msea.2018.07.087 ↗
18. Low temperature tensile deformation and acoustic emission signal characteristics of AISI 304LN stainless steel10.1016/j.msea.2013.12.067 ↗
19. Kinetics of deformation induced martensitic transformation in a 304 stainless steel10.1016/S1359-6462(01)01101-0 ↗
20. Charpy impact properties of stainless steel weldment in liquefied natural gas pipelines: effect of low temperatures10.1016/j.matdes.2014.09.085 ↗
21. A general mechanism of martensitic nucleation: Part II. FCC → BCC and other martensitic transformations
22. Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: Part II. Microstructural study10.1007/BF02644428 ↗
23. Effect of pre-straining on low-temperature mechanical behavior of AISI 304L10.1016/j.msea.2012.02.044 ↗
24. Temperature dependence of strain hardening and plastic instability behaviors in austenitic stainless steels10.1016/j.actamat.2004.05.003 ↗
25. A new constitutive model of austenitic stainless steel for cryogenic applications10.1016/j.commatsci.2009.06.003 ↗
26. Effect of cryogenic temperatures and processing parameters on gradient-structure of a stainless steel treated by ultrasonic surface mechanical attrition treatment10.1016/j.matchar.2018.02.028 ↗
27. Strain-rate effects on the mechanical behavior of the AISI 300 series of austenitic stainless steel under cryogenic environments10.1016/j.matdes.2010.02.041 ↗
28. A constitutive equation for predicting the material nonlinear behavior of AISI 316L, 321, and 347 stainless steel under low-temperature conditions10.1016/j.ijmecsci.2014.06.008 ↗
29. The development of a nitrogen-strengthened high-manganese austenitic stainless steel for a large superconducting magnet
30. A low-temperature study to examine the role of ε-martensite during strain-induced transformations in metastable austenitic stainless steels10.1016/j.actamat.2009.03.039 ↗
31. Twinning and martensite in a 304 austenitic stainless steel10.1016/j.msea.2012.05.080 ↗
32. In situ X-ray microdiffraction study of deformation-induced phase transformation in 304 austenitic stainless steel10.1016/j.actamat.2013.11.001 ↗
33. In situ synchrotron X-ray evaluation of strain-induced martensite in AISI 201 austenitic stainless steel during tensile testing10.1016/j.msea.2015.10.110 ↗
34. Martensite transformation behavior and mechanical properties of cold-rolled metastable Cr-Mn-Ni-N austenitic stainless steels10.1016/j.msea.2018.03.113 ↗
35. Microstructure and mechanical behavior of an AISI 304 austenitic stainless steel prepared by cold- or cryogenic-rolling and annealing10.1016/j.msea.2018.03.105 ↗
36. Effect of high magnetic field and uniaxial stress at cryogenic temperatures on phase stability of some austenitic stainless steels10.1016/j.msea.2006.01.124 ↗
37. Electron backscattered diffraction study of ε/α′ martensitic variants induced by plastic deformation in 304 stainless steel10.1007/s11661-005-0003-9 ↗
38. The morphologies and characteristics of impact-induced martensite in 304L stainless steel10.1016/S1359-6462(00)00487-5 ↗
39. A physically based model for TRIP-aided carbon steels behaviour10.1016/S0921-5093(03)00121-7 ↗
40. Deformation-induced martensite formation during cyclic deformation of metastable austenitic steel: influence of temperature and carbon content10.1016/j.msea.2006.12.211 ↗
41. Generation of dislocations during plastic deformation10.1016/S0254-0584(03)00064-6 ↗
42. Dislocations and plastic flow in crystals10.1119/1.1933704 ↗
43. Effect of strain rate upon plastic flow of steel10.1063/1.1707363 ↗