Mechanically enhanced novel Ti-based alloy foams obtained by hot pressing
Source abstract
Abstract
Abstract Ti-based alloys are being widely used as bio-implant materials because of their excellent properties. This work reports the synthesis of Ti–30Nb–13Ta–2Mn (wt. %) foams with and without bimodal microstructure using NaCl (0, 20 and 30 vol %) as space-holder particles (SHP). Samples with bimodal microstructure were obtained by mixing milled and un-milled powders in a proportion of 1:4. Samples without bimodal microstructure were synthesized using only un-milled powders. Hot pressing was used to consolidate the green samples using argon gas as protective atmosphere under 30 MPa at 780 °C for 30 min. The consolidated metallic foams were characterized by optical microscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD) to study their microstructure and phase analyses. The Young's modulus values were between 39 and 19 GPa, and the yield strength values were obtained between 180 and 400 MPa. From the mechanical properties point of view, samples with bimodal microstructure and with 20 and 30 vol % of NaCl have a great potential to be explored for biomedical applications due to their mechanical properties of Young's modulus smaller than 30 GPa and yield strength higher than 180 MPa. Further, the foams were modelled using finite element analysis (FEA) with random distribution of the pores in order to estimate the compressive behavior, and the Young's modulus measured using FEA was in an excellent agreement with the experimental data.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Titanium Alloys Microstructure and Properties · Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (77)
Show source-provided references
1. Mechanical properties and bioactive surface modification via alkali-heat treatment of a porous Ti–18Nb–4Sn alloy for biomedical applications10.1016/j.actbio.2008.04.022 ↗
2. Synthesis and characterization of Ti–Ta–Nb–Mn foams10.1016/j.msec.2015.08.053 ↗
3. Biocompatibility of Ti-alloys for long-term implantation10.1016/j.jmbbm.2012.11.014 ↗
4. Ti based biomaterials, the ultimate choice for orthopaedic implants–a review10.1016/j.pmatsci.2008.06.004 ↗
5. Titanium alloys in total joint replacement—a materials science perspective10.1016/S0142-9612(97)00146-4 ↗
6. Effect of alloying time and composition on the mechanical properties of Ti alloy10.1016/j.msea.2004.11.056 ↗
7. Electrochemical and XPS studies of corrosion behavior of Ti–23Nb–0.7 Ta–2Zr–O alloy in Ringer's solution10.1016/j.matchemphys.2008.08.043 ↗
8. Corrosion fatigue resistances of surgical implant stainless steels and titanium alloy10.1016/0010-938X(93)90193-K ↗
9. Corrosion resistance and corrosion fatigue strength of new titanium alloys for medical implants without V and Al10.1016/0921-5093(96)10247-1 ↗
10. Aging behavior of the Ti-29Nb-13Ta-4.6 Zr new beta alloy for medical implants10.1007/s11661-002-0110-9 ↗
11. Beta titanium alloys: the lowest elastic modulus for biomedical applications: a review
12. Production of new titanium alloy for orthopedic implants10.1016/j.msec.2004.08.011 ↗
13. Study on the microstructural evolution of Ti-Nb based alloy obtained by high-energy ball milling10.1016/j.jallcom.2017.05.262 ↗
14. A new look at biomedical Ti-based shape memory alloys10.1016/j.actbio.2012.01.018 ↗
15. Black · 2013
16. Anisotropy of Young's modulus of bone10.1038/283106a0 ↗
17. Ti based biomaterials, the ultimate choice for orthopaedic implants–a review10.1016/j.pmatsci.2008.06.004 ↗
18. Alloy phase diagrams
19. Collings · 1984 · 261
20. Leyens · 2003
21. Porous metals and metallic foams: current status and recent developments10.1002/adem.200800241 ↗
22. Highly porous open cell Ti-foam using NaCl as temporary space holder through powder metallurgy route10.1016/j.matdes.2013.01.005 ↗
23. Donachie · 2000
24. Bansiddhi · 2014 · 142
25. Potential applications for steel and titanium metal foams10.1007/s10853-005-4993-x ↗
26. Production and characterization of high porosity Ti-6Al-4V foam by space holder technique in powder metallurgy
27. Effect of pore size and relative density on the mechanical properties of open cell aluminum foams10.1016/j.scriptamat.2006.08.070 ↗
28. ALPORAS aluminum foam: production process, properties, and applications10.1002/(SICI)1527-2648(200004)2:4<179::AID-ADEM179>3.0.CO;2-G ↗
29. Novel titanium foam for bone tissue engineering10.1557/JMR.2002.0382 ↗
30. Processing of titanium foams using magnesium spacer particles10.1016/j.scriptamat.2006.11.010 ↗
31. High-strength Ti–6Al–4V with ultrafine-grained structure fabricated by high energy ball milling and spark plasma sintering10.1016/j.msea.2013.07.078 ↗
32. Processing of biomedical porous foam of Ti and Mg10.1016/S1359-6462(01)01132-0 ↗
33. Processing and properties of porous titanium using space holder technique10.1016/j.msea.2008.11.022 ↗
34. Properties of solid core and porous surface Ti–6Al–4V implants manufactured by powder metallurgy10.1016/j.jallcom.2006.12.143 ↗
35. Influence of cell aspect ratio on architecture and compressive strength of titanium foams10.1016/j.msea.2011.06.028 ↗
36. Titanium foam with coarser cell size and wide range of porosity using different types of evaporative space holders through powder metallurgy route10.1016/j.matdes.2014.05.054 ↗
37. Green strength of powder compacts provided for production of highly porous titanium parts10.1179/174329005X73838 ↗
38. Processing of porous Ti and Ti5Mn foams by spark plasma sintering10.1016/j.matdes.2010.06.019 ↗
39. Processing, characterization and biological testing of porous titanium obtained by space-holder technique10.1007/s10853-012-6586-9 ↗
40. Effects of addition of NH 4 HCO 3 on pore characteristics and compressive properties of porous Ti-10% Mg composites10.1016/S1003-6326(11)60824-8 ↗
41. Mechanical properties of open‐pore titanium foam10.1002/jbm.a.31118 ↗
42. Processing titanium foams using tapioca starch as a space holder10.1016/j.jmatprotec.2011.08.008 ↗
43. Fabrication of porous titanium scaffold with controlled porous structure and net-shape using magnesium as spacer10.1016/j.msec.2013.03.011 ↗
44. Characterization of Ti–6Al–4V alloy foams synthesized by space holder technique10.1016/j.msea.2011.01.008 ↗
45. The effect of the particle shape and strain rate on microstructure and compressive deformation response of pure Ti-foam made using acrowax as space holder10.1016/j.msea.2014.12.001 ↗
46. Powder metallurgical near‐net‐shape fabrication of porous NiTi shape memory alloys for use as long‐term implants by the combination of the metal injection molding process with the space‐holder technique10.1002/adem.200900168 ↗
47. Effect of microstructure on the tensile property of porous Ti produced by powder metallurgy technique10.1016/j.msea.2011.11.028 ↗
48. Fabrication, morphology and mechanical properties of Ti and metastable Ti-based alloy foams for biomedical applications10.1016/j.msec.2014.09.033 ↗
49. Micro-CT analysis and mechanical properties of Ti spherical and polyhedral void composites made with saccharose as a space holder material10.1016/j.matchar.2014.12.006 ↗
50. Titanium foam through powder metallurgy route using acicular urea particles as space holder10.1016/j.matlet.2011.07.004 ↗
51. Improvement of FEA estimations for compression behavior of Mg foams based on experimental observations10.1016/j.commatsci.2014.04.065 ↗
52. Study on the microstructural evolution of Ti-Nb based alloy obtained by high-energy ball milling10.1016/j.jallcom.2017.05.262 ↗
53. Determining periodic representative volumes of concrete mixtures based on the fractal analysis10.1016/j.ijsolstr.2012.05.017 ↗
54. Development of porous titanium for biomedical applications: a comparison between loose sintering and space-holder techniques10.1016/j.msec.2013.11.036 ↗
55. International centre for diffraction data (ICDD)
56. Development of a novel fcc structure for an amorphous-nanocrystalline Ti-33Nb-4Mn (at.%) ternary alloy10.1016/j.matchar.2017.11.021 ↗
57. Estimation of the Nb-Ti-Ta phase diagram10.1109/77.919892 ↗
58. Titanium foams produced by solid-state replication of NaCl powders10.1016/j.msea.2010.09.054 ↗
59. Study of the compression and wear-resistance properties of freeze-cast Ti and Ti‒5W alloy foams for biomedical applications10.1016/j.jmbbm.2017.04.020 ↗
60. Microstructure and mechanical properties of reticulated titanium scrolls10.1002/adem.201100082 ↗
61. Highly porous open cell Ti-foam using NaCl as temporary space holder through powder metallurgy route10.1016/j.matdes.2013.01.005 ↗
62. Shape-memory NiTi foams produced by replication of NaCl space-holders10.1016/j.actbio.2008.06.005 ↗
63. Processing and characterization of porous titanium for implants by using NaCl as space holder10.1016/j.jmatprotec.2011.12.015 ↗
64. Fabrication of novel TiZr alloy foams for biomedical applications10.1016/j.msec.2005.08.006 ↗
65. Influence of titanium surfaces on attachment of osteoblast-like cells in vitro10.1016/S0142-9612(03)00571-4 ↗
66. Effect of titanium surface characteristics on chondrocytes and osteoblasts in vitro
67. Fabrication methods of porous metals for use in orthopaedic applications10.1016/j.biomaterials.2005.12.002 ↗
68. High‐porosity titanium, stainless steel, and superalloy parts10.1002/(SICI)1527-2648(200004)2:4<196::AID-ADEM196>3.0.CO;2-K ↗
69. Biomaterial developments for bone tissue engineering10.1016/S0142-9612(00)00102-2 ↗
70. Effect of process control agent on the porous structure and mechanical properties of a biomedical Ti–Sn–Nb alloy produced by powder metallurgy10.1016/j.actbio.2009.10.005 ↗
71. The dependence of transversely isotropic elasticity of human femoral cortical bone on porosity10.1016/j.jbiomech.2003.12.011 ↗
72. Simultaneous structure and size–strain refinement by the Rietveld method10.1107/S0021889890002382 ↗
73. LSI-a computer program for simultaneous refinement of material structure and microstructure10.1107/S0021889892001122 ↗
74. Mechanical properties of nanocrystalline materials10.1016/j.pmatsci.2005.08.003 ↗
75. Mechanical properties and corrosion behaviour of nanocrystalline Ti–5Ta–1.8 Nb alloy produced by cryo-rolling10.1016/j.msea.2014.08.016 ↗
76. Hench · 2005
77. High tensile ductility in a nanostructured metal10.1038/nature01133 ↗