journal article·2018-11Open access

Cyclic and time-dependent crack growth mechanisms in Alloy 617 at 800 °C

Dylan A. Addison, Julie D. Tucker, Thomas Siegmund, Vikas Tomar, Jamie J. Kruzic

Abstract

Abstract Crack growth mechanisms for Alloy 617 at 800 °C were investigated in air with specific emphasis on the transition from cycle-dependent to time-dependent crack growth mechanisms in the creep-fatigue regime. Crack growth studies were conducted using compact tension samples, a load ratio of 0.5, and triangular 5 Hz, 0.33 Hz, and 0.05 Hz waveforms, a trapezoidal 0.05 Hz waveform with 17 s hold time, and sustained loading. Fatigue crack growth rates were relatively insensitive to changes in frequency and hold times in air up to ∆K ≈ 11.5 MPa√m for R = 0.5, i.e, Kmax = 23 MPa√m. Above this threshold, the onset of time dependent crack growth was observed via a creep void nucleation and coalescence mechanism for triangular and trapezoidal waveforms with a loading frequency of 0.05 Hz, and during sustained loading. An estimate of the threshold for stress assisted grain boundary oxidation (SAGBO) crack growth was calculated to be 23 MPa√m, and oxidized grain boundaries observed near the crack tip were mostly uncracked, suggesting the SAGBO threshold was not reached before the onset of the void nucleation mechanism. A comparison of results across all available studies suggests that a threshold-based transition from cycle- to time-dependent crack growth at 800 °C likely exists. However, the stress intensity factor does not maintain similitude to accurately define a threshold across studies. Thus, gaining an understanding of the crack tip stress states that define the various time dependent mechanisms should be considered in future work.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Fatigue and fracture mechanics · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Mizia · 2008
2. A review paper on aging effects in Alloy 617 for Gen IV nuclear reactor applications10.1115/1.2967885 ↗
3. A review on current status of Alloys 617 and 230 for Gen IV nuclear reactor internals and heat exchangers10.1115/1.3121522 ↗
4. Effect of helium environment on creep-rupture properties of Inconel 617 at 1000 °C10.1007/BF02658525 ↗
5. Enhanced oxygen diffusion within the internal oxidation zone of Alloy 617 in controlled impurity helium environments from 1023 K to 1123 K (750 °C to 850 °C)10.1007/s11661-015-2741-7 ↗
6. Benz · 2013
7. Time-dependent fatigue crack propagation behavior of two solid-solution-strengthened Ni-based superalloys-INCONEL 617 and HAYNES 23010.1007/s11661-011-0877-7 ↗
8. Fatigue and creep crack growth of Alloy 800 and Alloy 617 at high temperatures10.1080/09603409.1992.11689429 ↗
9. Lokhov · 2011
10. Thermal–mechanical stress analysis of pressurized water reactor pressure vessel with/without a preexisting crack under grid load following conditions10.1016/j.nucengdes.2016.09.020 ↗
11. Load following with small modular reactors analysis (SMR): a real options analysis10.1016/j.energy.2014.11.040 ↗
12. Inconel Alloy 617, Publication Number SMC-029, Special Metals Corporation, 2005.
13. Characterization of elevated temperature properties of heat exchanger and steam generator alloys10.1016/j.nucengdes.2011.10.034 ↗
14. ASTM Standard E647-15e1, Standard test method for measurement of fatigue crack growth rates, ASTM International, West Conshohocken, Pennsylvania, USA, 2015, 〈https://www.doi.org/10.1520/E0647-15E01〉, 〈www.astm.org〉.
15. ASTM Standard E1457, Standard test method for measurement of creep crack growth times and rates in metals, ASTM International, West Conshohocken, Pennsylvania, USA, 2013, 〈https://www.doi.org/10.1520/E1457-13〉, 〈www.astm.org〉.
16. ASTM Standard E2760-16, Standard test method for creep-fatigue crack growthtesting, ASTM International, West Conshohocken, Pennsylvania, USA, 2016,pp. 〈https://www.doi.org/10.1520/E2760-16〉, 〈www.astm.org〉.
17. J.R. Rice, H. Riedel, Tensile cracks in creeping solids, in: Proceedings of the 12th Conference on Fracture Mechanics, ASTM STP 700, ASTM International, 1980 pp. 112−130.10.1520/STP36967S ↗
18. Threshold stress creep behavior of Alloy 617 at intermediate temperatures10.1007/s11661-014-2244-y ↗
19. High temperature indentation based property measurements of IN-61710.1016/j.ijplas.2017.05.007 ↗
20. Experimental evaluation of the J or C* parameter for a range of cracked geometries10.1520/JAI13221 ↗
21. A critical analysis of crack propagation laws10.1115/1.3656900 ↗
22. Mechanism of plastic deformation of a Ni-based superalloy for VHTR applications10.1016/j.jnucmat.2013.03.083 ↗
23. Time-dependent crack growth thresholds of Ni-base superalloys10.1007/s11661-014-2271-8 ↗
24. Time-dependent crack-growth in a heat-resistant alloy Inconel-61710.1080/18811248.1993.9734487 ↗