journal article·2018-04

On the failure mechanism for high pressure die casting A390 hypereutectic alloy in low cycle and high cycle fatique

J. Wang, Z. Guo, X.Y. Jiao, L. Song, W.X. Hu, J.C. Li, S.M. Xiong

Publisher page

Abstract

Abstract The fatique failure behavior of A390 hypereutectic aluminum alloy plate was studied with laboratory CT and such technique provided a new method for analyses of the mechanical failure. Results were based on the reconstructed fractography and SEM observation and special attention was paid to crack propagation mechanism in the hypereutectic alloy. The fatique crack surface was separated into crack initiation site around pores, flat crack propagation zone and instantaneous crack zone. While the flat crack propagation zone only occurred in high cycle fatique and the height fluctuation of flat propagation was within 50 µm. The disappearance of flat propagation in low cycle fatique showed the different crack propagation mechanism between hypereutectic and hypoeutectic alloy. Different crack propagation stage changed with the stress intensity of crack tip. The flat propagation zones for high cycle fatique attributed to the relatively parallel extension of crack and debonding between PSPs and matrix in hypereutectic alloy. While under higher stress intensity like the case in LCF or later stage of HCF, the crack branched and extended instantaneously, tortuous crack propagation route formed and many PSPs with minor cracks or striations remained.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Metallurgy and Material Forming · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Application of cast Al–Si alloys in internal combustion engine components10.1179/1743280413Y.0000000027 ↗
2. Review of microstructure evolution in hypereutectic Al–Si alloys and its effect on wear properties10.1007/s12666-013-0327-x ↗
3. Porosity and the fatigue behavior of hypoeutectic and hypereutectic aluminum–silicon casting alloys10.1016/j.ijfatigue.2007.08.012 ↗
4. On the porosity induced by externally solidified crystals in high-pressure die-cast of AM60B alloy and its effect on crack initiation and propagation10.1016/j.msea.2015.02.078 ↗
5. Failure behavior of high pressure die casting AZ91D magnesium alloy10.1016/j.msea.2016.07.009 ↗
6. Elevated temperature short crack fatigue behaviour in near eutectic Al–Si alloys10.1016/S0142-1123(03)00157-9 ↗
7. Effect of silicon particles on the fatigue crack growth characteristics of Al-12 Wt Pct Si-0.35 Wt Pct Mg-(0 to 0.02) Wt Pct Sr casting alloys10.1007/BF02647606 ↗
8. The effect of silicon content on long crack fatigue behaviour of aluminium–silicon piston alloys at elevated temperature10.1016/j.ijfatigue.2005.06.023 ↗
9. Microstructural Analysis of Fatigue Initiation in Al-Si Casting Alloys10.4028/www.scientific.net/MSF.519-521.1083 ↗
10. Analysis of fatigue crack initiation and S–N response of model cast aluminium piston alloys10.1016/j.msea.2011.06.007 ↗
11. Monotonic and cyclic deformation behavior of the Al–Si–Cu–Mg cast alloy with micro-additions of Ti, V and Zr10.1016/j.ijfatigue.2014.08.001 ↗
12. Understanding fatigue crack growth in aluminum alloys by in situ X-ray synchrotron tomography10.1016/j.ijfatigue.2012.06.009 ↗
13. Three-dimensional analysis of fatigue crack propagation using X-ray tomography, digital volume correlation and extended finite element simulations10.1016/j.piutam.2012.05.017 ↗
14. Quantitative evaluation of fatigue life of cast aluminum alloys by non-destructive testing and parameter model10.1016/j.ijfatigue.2013.05.017 ↗
15. Thermo Fisher Scientific: Amira-Avizo 3D Software, 〈http://www.fei.com/software/avizo3d/〉, 2017 (Accessed 20 September 2017).
16. Characterisation of the 3-D dendrite morphology of magnesium alloys using synchrotron X-ray tomography and 3-D phase-field modelling10.1016/j.actamat.2015.03.044 ↗
17. Characterization of the morphology of primary silicon particles using synchrotron X-ray tomography10.1016/j.matchar.2016.12.004 ↗
18. On the growth mechanism of the primary silicon particle in a hypereutectic Al-20wt%Si alloy using synchrotron X-ray tomography10.1016/j.matdes.2017.09.062 ↗
19. Fatigue strength and failure mechanisms of wrought aluminium alloys in the VHCF-region considering material and component relevant influencing factors10.1016/j.ijfatigue.2010.05.008 ↗
20. Subra · 1998
21. Peterson' stress concentration factors
22. 3D characterization and modeling of low cycle fatigue damage mechanisms at high temperature in a cast aluminum alloy10.1016/j.actamat.2016.10.028 ↗
23. Quantification of the interaction within defect populations on fatigue behavior in an aluminum alloy10.1016/j.actamat.2009.04.008 ↗
24. Dynamic deformation and fracture of single crystal silicon: fracture modes, damage laws, and anisotropy10.1016/j.actamat.2016.05.022 ↗
25. Study on dominant mechanism of high-cycle fatigue life in 6061-T6 aluminum alloy through microanalyses of microstructurally small cracks10.1016/j.actamat.2012.01.023 ↗
26. Three-dimensional visualization of ductile fracture in an Al–Si alloy by high-resolution synchrotron X-ray microtomography10.1016/j.msea.2006.10.201 ↗
27. A model for the formation of fatigue striations and its relationship with small fatigue crack growth in an aluminum alloy10.1016/j.ijfatigue.2010.05.005 ↗
28. Three-dimensional fatigue crack growth behavior in an aluminum alloy investigated with in situ high-resolution synchrotron X-ray microtomography10.1016/j.actamat.2009.03.036 ↗
29. Crack closure effect and crack growth behavior in GH2036 superalloy plates under combined high and low cycle fatigue10.1016/j.ijfatigue.2016.10.011 ↗
30. Effect of microstructural features on fatigue behavior in A319-T6 aluminum alloy10.1016/j.msea.2010.02.055 ↗
31. In situ characterization of fatigue damage evolution in a cast Al alloy via nonlinear ultrasonic measurements10.1016/j.actamat.2009.11.055 ↗
32. Experimental investigation for fatigue strength of a cast aluminium alloy10.1016/j.ijfatigue.2010.09.002 ↗
33. High cycle fatigue strength of permanent mold and rheocast aluminum 357 alloy10.1016/j.ijfatigue.2010.01.001 ↗
34. Micromechanisms of fatigue crack growth in cast aluminium piston alloys10.1016/j.ijfatigue.2011.10.015 ↗
35. Microtomographic study and finite element analysis of the porosity harmfulness in a cast aluminium alloy10.1016/j.ijfatigue.2011.06.010 ↗
36. Influence of porosity on the fatigue limit of die cast magnesium and aluminium alloys10.1016/S0142-1123(02)00054-3 ↗
37. Fatigue crack propagation: In situ visualization using X-ray microtomography and 3D simulation using the extended finite element method10.1016/j.actamat.2005.10.053 ↗
38. Three-dimensional characterisation and modelling of small fatigue corner cracks in high strength Al-alloys10.1016/j.crhy.2011.12.005 ↗
39. Broek · 1988
40. A 3D measurement procedure for internal local crack driving forces via synchrotron X-ray microtomography10.1016/j.actamat.2003.11.014 ↗
41. Role of eutectic silicon particles in fatigue crack initiation and propagation and fatigue strength characteristics of cast aluminum alloy A35610.1016/j.engfracmech.2013.11.016 ↗
42. Low cycle fatigue behavior of casting A319 alloy under two different aging conditions10.1016/j.msea.2015.12.023 ↗
43. Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting10.1038/s41598-017-15223-w ↗
44. Tensile and fatigue properties of gravity casting aluminum alloys for engine cylinder heads10.1016/j.msea.2013.08.016 ↗
45. Fracture behaviors of A390 aluminum cylinder liner alloys under static loading10.1016/j.jallcom.2012.10.116 ↗
46. Effect of grain size on fatigue-crack growth in 2524 aluminium alloy10.1016/j.ijfatigue.2015.11.011 ↗