journal article·2018-05

A novel approach to extracting hardness of copper/niobium (Cu/Nb) multilayer films by removing the substrate effect

Y.H. Qiu, Q. Bai, E.G. Fu, P.P. Wang, J.L. Du, X.F. Chen, J.M. Xue, Y.G. Wang, X.J. Wang

Publisher page

Abstract

Abstract This article presents a novel method to eliminate the substrate effect in soft thin film on hard substrate by correcting the projected contact area in nanoindentation test. The hardness of sputtered Cu/Nb multilayer films on silicon substrate with different individual layer thickness was measured by nanoindentation in continuous stiffness mode (CSM) and was shown to be influenced by both indentation size effect (ISE) and substrate effect. Finite element modeling (FEM) and atomic force microscope (AFM) were used to investigate the influence of substrate to the hardness measurement, and the results showed that the hardness deviation induced by the substrate effect resulted from the pile-up can be reasonably removed. Silicon substrate was found to be crucial for the pile-up formation, as the vertical plastic flow of soft Cu/Nb film was restrained by hard silicon substrate with the increase of indentation depth. After applying our pile-up correction and revised Nix-Gao fitting, the hardness curves show a depth independent relation, which fulfills the requirement for accurate hardness measurement. We showed that the hardness deviation due to pile-up is about 14%. Meanwhile, some vague issues like the plateau region and “one-tenth rule” applied in many studies were discussed and clarified basing on our experimental and modeling results. The correcting methods and simulation results could be instructive and significant for nanoindentation hardness test of similar soft film on hard substrate system.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Copper Interconnects and Reliability · Adhesion, Friction, and Surface Interactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Relationship between damage and hardness profiles in ion irradiated SS316 using nanoindentation – experiments and modelling10.1016/j.ijplas.2016.08.006 ↗
2. Investigations on the mechanical properties of the elementary thin films composing a CuIn1−xGaxSe2 solar cell using the nanoindentation technique10.1016/j.tsf.2016.11.013 ↗
3. Evolution characteristics of residual stress in metastable Ni-B alloy coatings identified by nanoindentation10.1016/j.surfcoat.2016.08.042 ↗
4. The indentation size effect: a critical examination of experimental observations and mechanistic interpretations10.1146/annurev-matsci-070909-104456 ↗
5. The indentation size effect in the spherical indentation of iridium: a study via the conventional theory of mechanism-based strain gradient plasticity10.1016/j.ijplas.2005.07.008 ↗
6. Substrate effects and evaluation of elastic moduli of components of inhomogeneous films by nanoindentation10.1016/j.tsf.2016.11.018 ↗
7. On the intrinsic hardness of a metallic film/substrate system: indentation size and substrate effects10.1016/j.ijplas.2012.01.001 ↗
8. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
9. Effects of the substrate on the determination of thin film mechanical properties by nanoindentation10.1016/S1359-6454(01)00328-7 ↗
10. Nanoindentation in materials research: past, present, and future10.1557/mrs2010.717 ↗
11. A comparison of nanoindentation pile-up in bulk materials and thin films10.1016/j.tsf.2014.06.060 ↗
12. Investigation of pile-up during a rigid ball sliding on coated surface based on elastic–plastic analysis10.1016/j.surfcoat.2014.04.040 ↗
13. Substrate effects on nanoindentation mechanical property measurement of soft films on hard substrates10.1557/JMR.1999.0042 ↗
14. Determination of indenter tip geometry and indentation contact area for depth-sensing indentation experiments10.1557/JMR.1998.0185 ↗
15. Combinatorial studies of mechanical properties of Ti–Al thin films using nanoindentation10.1016/j.actamat.2005.01.017 ↗
16. Semi-ellipse method for accounting for the pile-up contact area during nanoindentation with the Berkovich indenter10.1016/j.scriptamat.2006.06.030 ↗
17. An improved method to estimate Young's modulus of Zr-based BMGs accounting for pile-up during nanoindentation10.1016/j.jnoncrysol.2015.07.031 ↗
18. Correcting for contact area changes in nanoindentation using surface acoustic waves10.1016/j.scriptamat.2016.09.037 ↗
19. An improved technique for determining hardness and elastic-modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
20. A nanoindentation study of copper films on oxidised silicon substrates10.1016/S0257-8972(03)00774-6 ↗
21. Critical review of analysis and interpretation of nanoindentation test data10.1016/j.surfcoat.2005.03.018 ↗
22. Finite element analysis on nanoindentation with friction contact at the film/substrate interface10.1016/j.compscitech.2006.10.005 ↗
23. Indentation behavior of metal–ceramic multilayers at the nanoscale: numerical analysis and experimental verification10.1016/j.actamat.2009.11.046 ↗
24. Investigation of material properties of thin copper films through finite element modelling of microindentation test10.1016/j.apsusc.2008.02.101 ↗
25. Some features of the energy dissipation in the course of plastic deformation of iron and niobium10.1134/1.1432372 ↗
26. A numerical study of factors affecting the characterization of nanoindentation on silicon
27. Length-scale-dependent deformation mechanisms in incoherent metallic multilayered composites10.1016/j.actamat.2005.06.025 ↗
28. Indentation size effects in crystalline materials: a law for strain gradient plasticity10.1016/S0022-5096(97)00086-0 ↗
29. Indentation size effect in metallic materials: correcting for the size of the plastic zone10.1016/j.scriptamat.2005.02.009 ↗
30. Defect structures and hardening mechanisms in high dose helium ion implanted Cu and Cu/Nb multilayer thin films10.1016/j.ijplas.2011.12.007 ↗