The influence of the indentation size in relation to the size of the microstructure of three polycrystalline materials indented with a Berkovich indenter
Source abstract
Abstract
Three different polycrystalline materials, a fine-grained martensitic steel (CrMoV), a coarse-grained high-purity copper (C110), and a two-phase microstructure titanium alloy (Ti-6Al-4V), have been selected to investigate the heterogeneity of deformation following indentation using a depth-sensing indentation instrument fitted with a Berkovich indenter. The geometry of the pile-up profiles, measured with an atomic force microscope, were observed to be very sensitive to the indentation size with respect to the size of the microstructure and the material properties and crystallographic plane of the indented grain. In contrast, neither the recovery of the area of indentation nor the degree of piling-up were affected by the presence of indentation size effects (ISE). Furthermore, based on the results of a full-3D finite element simulation, it was concluded that the misalignment of the indenter alone does not explain the significantly asymmetric piling-up in highly anisotropic materials, e.g. C110 copper, but that this is due to the crystallographic orientation of the single grain tested. In addition, the experimental results revealed that, although a thicker mechanically hardened layer formed during polishing is more prone to recovery during unloading, leading to a smaller residual indented area, the degree of piling-up is unaffected provided that the ratio of maximum depth (hmax) to the thickness of the strain-hardened layer is above unity. Moreover, on the same premise, the surface roughness and the thickness of the strain-hardened layer can be discarded as length parameters affecting hardness measurements.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced Surface Polishing Techniques · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Hardness measurement at penetration depths as small as 20 nm10.1080/01418618308234914 ↗
2. Vickers indentation curves of magnesium oxide (MgO)10.1115/1.3260865 ↗
3. A method for interpreting the data from depth-sensing indentation instruments10.1557/JMR.1986.0601 ↗
4. ISO-14577-1:2015 Metallic Materials - Instrumented Indentation Test for Hardness and Materials Parameters - Part 1: Test Method, 1 rue de Varembé, 1211 Geneva 20 Switzerland, 2015.
5. Size dependent hardness of silver single crystals10.1557/JMR.1995.0853 ↗
6. Determination of indenter tip geometry and indentation contact area for depth-sensing indentation experiments10.1557/JMR.1998.0185 ↗
7. Depth dependence of hardness in copper single crystals measured by nanoindentation10.1016/S1359-6462(00)00598-4 ↗
8. Strain gradient plasticity: theory and experiment10.1016/0956-7151(94)90502-9 ↗
9. The frictional component of the indentation size effect in low load microhardness testing10.1557/JMR.1993.1028 ↗
10. Indenter tip radius effect on the Nix–Gao relation in micro- and nanoindentation hardness experiments10.1557/JMR.2004.0441 ↗
11. Use of the indentation size effect on microhardness for materials characterization
12. The influence of grain size on the indentation hardness of high-purity copper and aluminium10.1080/01418610208235717 ↗
13. Microindentations on Q and Mo oriented single crystals: an STM study10.1016/0956-7151(93)90100-7 ↗
14. Orientation dependence of nanoindentation pile-up patterns and of nanoindentation microtextures in copper single crystals10.1016/j.actamat.2004.01.016 ↗
15. Depth dependence of nanoindentation pile-up patterns in copper single crystals10.1007/s11661-014-2437-4 ↗
16. Fischer-Cripps · 2004
17. Kuhn · 2000
18. ISO 4287:1997 Geometrical Product Specifications (GPS), Surface Texture: Profile Method. Terms, Definitions and Surface Texture Parameters, 1 rue de Varembé, 1211 Geneva 20 Switzerland, 1997.
19. Analysis of berkovich indentation10.1016/0020-7683(95)00033-7 ↗
20. Bhadeshia · 2006
21. D. Tabor, A Simple Theory of Static and Dynamic Hardness. Proc. R. Soc. Lond. A, 192, pp. 247–274.10.1098/rspa.1948.0008 ↗
22. N.A. Stillwell, D. Tabor, Elastic Recovery of Conical Indentations. Proc. Phys. Soc., 78(2), pp. 169–179.10.1088/0370-1328/78/2/302 ↗
23. Callister · 1940
24. Elastic modulus of Ti–6Al–4V–xB alloys with B up to 0.55wt%10.1016/j.scriptamat.2009.09.022 ↗
25. Experiments and crystal plasticity finite element simulations of nanoindentation on Ti-6Al-4V alloy10.1016/j.msea.2014.11.090 ↗
26. Meyers · 2009