journal article·2014-04

Experimental determination and prediction of the mechanical properties of steel 1.7225

J. Brnic, G. Turkalj, M. Canadija, J. Niu

Publisher page

Abstract

This paper presents experimental results and the analysis of the behavior of steel 1.7225 at different temperatures. First, experimental results related to the mechanical properties of the material and its resistance to creep are shown using stress-strain diagrams and creep curves. Then, the analysis of the sensitivity of the ultimate tensile strength with respect to strain rate is given. Modeling of some creep curves using an analytic formula is also presented. An assessment of the fracture toughness based on Charpy impact energy is made. The obtained results show that both ultimate tensile strength and yield strength achieve their maximum at room temperature, but these values are reduced with an increase in temperature up to 650K. At this temperature, they achieve approximately 20% of initial values. Notably, this steel may be treated as creep resistant only when it is subjected to a low level of stress at considered temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Temperature Alloys and Creep · Fire effects on concrete materials · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (25)

Show source-provided references
1. Gross · 2011
2. Barsom · 1999
3. Raghavan · 2004
4. Terres · Mater. Des. · 2012 · 35 · 74110.1016/j.matdes.2011.09.055 ↗
5. Pfennig · Corros. Sci. · 2012 · 65 · 44110.1016/j.corsci.2012.08.041 ↗
6. Schulze · Proc. Eng. · 2011 · 19 · 33110.1016/j.proeng.2011.11.121 ↗
7. Schulze · Proc. CIRP · 2013 · 8 · 3310.1016/j.procir.2013.06.061 ↗
8. Ahmadi · Int. J. Fatigue · 2005 · 27 · 85310.1016/j.ijfatigue.2005.02.005 ↗
9. Bayrak · J. Mater. Eng. Perform. · 2007 · 16 · 59710.1007/s11665-007-9043-1 ↗
10. Huang · Mater. Des. · 2014 · 53 · 34910.1016/j.matdes.2013.06.070 ↗
11. Kang · Int. J. Plast. · 2009 · 25 · 83810.1016/j.ijplas.2008.06.004 ↗
12. Kang · Mater. Sci. Eng. A · 2008 · 472 · 25810.1016/j.msea.2007.03.029 ↗
13. Hor · Int. J. Mech. Sci. · 2013 · 67 · 10810.1016/j.ijmecsci.2013.01.003 ↗
14. Cai · Adv. Mater. Res. · 2012 · 538–541 · 43110.4028/www.scientific.net/AMR.538-541.431 ↗
15. Chen · Acta Metall. Sin. · 2012 · 48 · 118610.3724/SP.J.1037.2012.00340 ↗
16. Brnic · Mater. Des. · 2013 · 47 · 49710.1016/j.matdes.2012.12.037 ↗
17. Herakovič · Mater. Technol. · 2010 · 44 · 37
18. Brnic · Mech. Time-Depend. Mater. · 2011 · 15 · 34110.1007/s11043-011-9137-x ↗
19. Brnic · Mater. Manuf. Process. · 2009 · 24 · 75810.1080/10426910902809800 ↗
20. Brnic · J Constr. Steel Res. · 2011 · 67 · 194810.1016/j.jcsr.2011.06.011 ↗
21. Annual Book of ASTM Standards, Metal Test Methods and Analytical Procedures, vol. 03.01, ASTM International, Baltimore, 2012.
22. Dowling · 2013
23. M.P. Blinn, R.A.Williams, Design for fracture toughness, in: ASTM Handbook, vol. 20, Materials Selection and Design, Dieter, G.E., Volume Chair, ASM International, USA, 1997, pp. 533–544.10.31399/asm.hb.v20.a0002470 ↗
24. B.I. Bramfitt, Effects of composition, processing and structure on properties of irons and steels, in: ASTM Handbook, vol. 20, Materials Selection and Design, Dieter, G.E., Volume Chair, ASM International, USA, 1997, pp. 357–382.10.31399/asm.hb.v20.a0002461 ↗
25. Chao · Mater. Des. · 2007 · 28 · 55110.1016/j.matdes.2005.08.009 ↗