Micromechanical investigation of the role of percolation on ductility enhancement in metallic glass composites
Source abstract
Abstract
Abstract In contrast to the catastrophic failure arising from the unconstrained shear band propagation in monolithic bulk metallic glasses (BMGs), the introduction of second phases in BMG composites (BMGCs) provides an extrinsic way of reducing the magnitude of strain localization, and thus may significantly improve the ductility. For this mechanism to be effective, a multitude of experiments have found that the volume fraction should reach a rather high threshold of about 30–40%, corresponding to the percolation limit with variations depending on the second phase morphology. However, we demonstrate here that an enhanced ductility can be realized in a BMGC made from crystalline Ni foam (completely percolated even with a volume fraction of about 11%), suggesting the resistance in the second phase to the impinging shear-force dipole from neighboring shear bands be the dominant factor for such a ductility improvement. The shortcomings of percolation approach, as well as the synergistic effects of microstructure and mismatches in mechanical properties, are investigated here in a thermo-mechanical finite element method based on the free volume model and plasticity-induced heating. The effectiveness of ductility improvement will be demonstrated by calculating the probability distributions of the shear-band effective strain.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metallic Glasses and Amorphous Alloys · Electromagnetic wave absorption materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (17)
Show source-provided references
1. A microscopic mechanism for steady state inhomogeneous flow in metallic glasses10.1016/0001-6160(77)90232-2 ↗
2. Insights from the lattice-strain evolution on deformation mechanisms in metallic-glass-matrix composites10.1007/s11661-015-2764-0 ↗
3. Designing metallic glass matrix composites with high toughness and tensile ductility10.1038/nature06598 ↗
4. Suppression of the shear band instability during plastic flow of nanometer-scale confined metallic glasses10.1063/1.2821227 ↗
5. Development of tough, low-density titanium-based bulk metallic glass matrix composites with tensile ductility10.1073/pnas.0809000106 ↗
6. Ta-particulate reinforced Zr-based bulk metallic glass matrix composite with tensile plasticity10.1016/j.scriptamat.2009.11.018 ↗
7. Effect of a controlled volume fraction of dendritic phases on tensile and compressive ductility in La-based metallic glass matrix composites10.1016/j.actamat.2004.05.025 ↗
8. An atomistic investigation of structural evolution in metallic glass matrix composites10.1016/j.ijplas.2013.01.002 ↗
9. Numerical simulation on the deformation behaviors of bulk metallic glass composites under uniaxial tension and compression10.1016/j.compstruct.2017.12.070 ↗
10. Microstructural percolation assisted breakthrough of trade-off between strength and ductility in CuZr-based metallic glass composites10.1038/srep04167 ↗
11. Microstructural tailoring and improvement of mechanical properties in CuZr-based bulk metallic glass composites10.1016/j.actamat.2012.02.017 ↗
12. Microstructural heterogeneities governing the deformation of Cu47. 5Zr47. 5Al5 bulk metallic glass composites10.1016/j.actamat.2009.07.042 ↗
13. An implicit finite element method for simulating inhomogeneous deformation and shear bands of amorphous alloys based on the free-volume model10.1088/0965-0393/14/8/004 ↗
14. On the origin of shear banding instability in metallic glasses10.1016/j.jmps.2009.04.008 ↗
15. Nature of crack-tip plastic zone in metallic glasses10.1016/j.ijplas.2015.10.004 ↗
16. Sadd · 2009
17. An improved relation for the effective elastic compliance of a film/substrate system during indentation by a flat cylindrical punch10.1016/j.scriptamat.2006.04.037 ↗