Effect of temperature on low cycle fatigue behavior of annealed Cu-Cr-Zr-Ti alloy in argon atmosphere
Source abstract
Abstract
Abstract Isothermal low cycle fatigue (LCF) properties of Cu-Cr-Zr-Ti alloy were evaluated at different temperatures (300 °C, 450 °C and 600 °C) in high purity argon atmosphere. The cyclic stress response (CSR) was highly dependent on the test temperature. CSR at 300 °C showed primary hardening and secondary hardening at lower strain amplitudes from 0.25% to 0.8% and primary hardening followed by continuous softening at 1.2% strain amplitude. At 450 °C, the alloy exhibited a higher degree of primary hardening followed by saturation of stress. Transmission electron microscopic observations made on the samples tested upto different number of cycles indicate that precipitation of fine Cr precipitates was the main reason for the secondary hardening at 300 °C and extensive primary hardening at 450 °C. Even though precipitation was assisted by mechanical working during cycling, it is observed that the secondary hardening occurred almost at the same time irrespective of the strain amplitude used in the tests. At 450 °C and higher strain amplitudes, precipitates nucleated at the dislocations within a few initial cycles causing pinning of the dislocations thereby increasing the stress response. CSR at 600 °C showed continuous softening without any hardening. It is found that the precipitates nucleated during heating and soaking at the test temperature itself before the start of the strain cycling and coarsening of precipitates as well as loss of coherency with the matrix caused continuous softening at 600 °C. With an increase in test temperature, a reduction in fatigue life is observed and the life reduction is significant at higher strain amplitudes. Microstructural observations and fractographic studies indicated that cracks initiated predominantly at surface and propagated inward. Intergranular cracking was observed at higher strain amplitudes at all temperatures.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Microstructure and mechanical properties · High Temperature Alloys and Creep · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. Comparative analysis of copper alloys for the heat sink of plasma facing components in ITER10.1016/S0022-3115(98)00271-2 ↗
2. L. David Ellis, Observations of a Cast Cu-Cr-Zr Alloy, NASA/TM—2006-213968, National Aeronautics and Space Administration, John H. Glenn Research Center at Lewis Field, Cleveland, Ohio 44135–3191, 2006.
3. Fatigue behavior of copper and selected copper alloys for high heat flux applications10.1016/S0022-3115(96)00243-7 ↗
4. Room temperature creep-fatigue response of selected copper alloys for high heat flux applications10.1016/j.jnucmat.2004.04.278 ↗
5. Singh · 2005
6. Material parameters of copper and CuCrZr alloy for cyclic plasticity at elevated temperatures10.1016/j.jnucmat.2007.06.005 ↗
7. Dynamic embrittlement in an age-hardenable copper-chromium alloy10.1016/1359-6462(96)00098-X ↗
8. On the dynamic embrittlement of copper-chromium alloys by sulphur10.1023/A:1004839825660 ↗
9. New high-temperature copper alloys10.1007/BF02646904 ↗
10. Effect of simulated brazing cycle on the microstructure and properties of Cu-Cr-Zr-Ti alloy10.4028/www.scientific.net/MSF.710.626 ↗
11. Microstructural analysis of a failed Cu-Cr-Ti-Zr thrust chamber liner of a cryogenic engine
12. Analysis of phases and their role in strengthening of Cu-Cr-Zr-Ti alloy10.1007/s11665-015-1516-z ↗
13. Dynamic embrittlement in Cu-Cr-Zr-Ti alloy: Evidence of intergranular segregation of sulphur10.1007/s11665-013-0510-6 ↗
14. Low cycle fatigue behaviour of a Cu-Cr-Zr-Ti alloy10.1016/j.proeng.2013.03.238 ↗
15. Effects of temperature and strain rate on tensile properties of Cu-Cr-Zr-Ti alloy10.1016/j.msea.2016.05.035 ↗
16. Influence of plastic deformation on the precipitation of Cr in copper10.1007/s10853-014-8348-3 ↗
17. Research on aging precipitation in a Cu-Cr-Zr-Mg alloy10.1016/j.msea.2004.09.041 ↗
18. Activation energy for precipitation in undeformed and deformed Cu-Cr alloys10.1002/pssa.2211080153 ↗
19. Interaction of cold work, recovery, recrystallization, and precipitation in heat-treatable copper alloys10.1179/030716979803276039 ↗
20. Microstructural investigations into the low cycle fatigue deformation of a Cu–Cr–Zr–Ti alloy10.1016/j.msea.2013.06.034 ↗
21. Singh · 2004
22. Investigation on the microstructure and mechanical properties of CuCrZr after manufacturing thermal cycle for plasma facing component10.1016/j.jnucmat.2010.12.157 ↗
23. Microstructure and properties of aging Cu–Cr–Zr alloy10.1007/s12598-014-0244-0 ↗
24. Analysis of precipitation in a Cu – Cr – Zr alloy
25. Low energy dislocation structures produced by cyclic softening10.1016/0921-5093(89)90313-4 ↗
26. Cyclic softening in annealed polycrystalline copper10.1016/0921-5093(92)90353-3 ↗
27. Fatigue softening in precipitation hardened copper-cobalt10.1016/0036-9748(82)90161-2 ↗
28. Intermediate temperature embrittlement of copper alloys10.1179/174328009X392967 ↗